Incubator escapee wiki

Chevrolet Turbo-Air 6 engine

Article Discussion

Template:Infobox automobile engine

The Chevrolet Turbo-Air 6 is a flat-six air-cooled automobile engine developed by General Motors (GM) in the late 1950s for use in the rear-engined Chevrolet Corvair of the 1960s. It was used in the entire Corvair line, as well as a wide variety of other applications.

The engine's use of air cooling made it appealing to aircraft amateur builders, and small-volume engine builders established a cottage industry modifying Corvair engines for aircraft.<ref name="WDLA11"/>

HistoryEdit

Ed Cole, Chief Engineer for Chevrolet from 1952 to 1956 and Chevrolet General Manager from 1956 to 1961, was the person primarily responsible for getting the Corvair and its engine into production. Cole's experience with rear-engined vehicles began during his time as chief design engineer of light tanks and combat vehicles for Cadillac during World War II. He designed powertrains for the M24 Chaffee light tank and M5 Stuart tank, the latter of which used two rear-mounted Cadillac V8 engines driving through Hydramatic transmissions.

After the war, Cole was promoted to Chief Engineer at Cadillac. In 1946, he began experimenting with rear-engined passenger car prototypes, nicknamed "Cadibacks".<ref name="reuters"/><ref name="knepperbook"/>Template:Rp

In 1950, Cole was asked to oversee production of the M41 Walker Bulldog tank at Cadillac's Cleveland facility. The M41 was powered by a Continental AOS-895-3 engine.<ref name="lvcc-jan2012"/> This was a six-cylinder, air-cooled, four-stroke supercharged boxer engine that displaced Template:Cvt.

Cole also logged over 300 hours piloting a Beechcraft Bonanza powered by a smaller Continental engine with the same basic layout.<ref name="excellencemag"/><ref name="muellerbook"/>Template:Rp

After moving to Chevrolet, Cole instructed engineer Maurice Olley to come up with "something different". Olley and his team assessed both front-engine/front-wheel-drive and rear-engine, rear-wheel-drive layouts and determined that the rear/rear layout would need an engine of aluminum, and that air-cooling would be preferred.<ref name="knepperbook"/>Template:Rp

Responsibility for development of the engine fell primarily to Senior Project Engineer Robert P. Benzinger and engine designer Adelbert “Al” Kolbe.<ref name="vv-benzinger"/> The first engine was fired up in the Chevrolet Engineering department in December 1957.<ref name="knepperbook"/>Template:Rp For the earliest road tests, a prototype was installed in a Porsche 356. Later development mules were either called LaSalle II or badged as Holdens.

A new casting foundry was built in Massena, New York, at Massena Castings Plant.<ref name="knepperbook"/>Template:Rp GM convinced Reynolds Aluminum to build an aluminum reduction plant nearby to supply it. Aluminum parts included the block, heads, flywheel housing, crankcase cover, clutch housing and pistons. Template:Cvt of aluminum was used in each engine. New casting and machining techniques had to be developed to produce the light-alloy parts. The aluminum parts were cast with a low-pressure casting technique using machines built and installed by Karl Schmidt GmbH of Neckarsulm, Germany.<ref name="dce-sep2006"/><ref name="auwm-corpage2"/> All of the engines were assembled at GM's Tonawanda Engine plant.<ref name="vv-jan2011"/><ref name="auwm-corpage2"/>

The car and engine were officially introduced on 29 September 1959 and debuted in showrooms on 2 October.<ref name="knepperbook"/>Template:Rp Advertising prepared by the Campbell-Ewald agency highlighted the fact that the air-cooled engine did not require anti-freeze, and that much of the engine was made of "aircraft-type" aluminum.<ref name="knepperbook"/>Template:Rp The same ad agency gave the engine its official name, the "Turbo-Air 6".<ref name="knepperbook"/>Template:Rp

The Turbo-Air 6 engine was used in all Corvair car models in all trim levels, including the 500, 700, 900 Monza, Corsa, and Spyder coupes sedans and convertibles, as well as the Corvair and Lakewood station-wagons. It also powered the Forward-Control 95 series vans, including the Corvan and the Chevrolet Greenbrier van, and both the Loadside and Rampside pickup trucks.

Tuned versions of the engine appeared in some modified Corvairs sold under the customizer's name, such as the Fitch Sprint, the Yenko Stinger, and the Solar Cavalier. Don Yenko claimed as much as Template:Cvt from his Stage IV and racing Stingers.<ref name="knepperbook"/>Template:Rp

Manufacturing of the Turbo-Air 6 ended with the cessation of Corvair production after 1969.

Technical featuresEdit

The Turbo-Air 6 is a flat-six engine that is primarily air-cooled. The engine's major components include an aluminum crankcase, two three-cylinder aluminum cylinder heads with integral intake manifolds, and six individual iron cylinder barrels. The #1 cylinder is at the right rear with cylinders 1, 3, and 5 on the right, while #2 is the left rear with cylinders 2, 4, and 6 on the left.<ref name="fiorebook"/>Template:Rp The firing order is: 1-4-5-2-3-6.

The crankcase is cast as two box-section halves. The assembled crankcase provides for four main bearings. There are four cylinder head studs per cylinder, for a total of twelve on each side.<ref name="knepperbook"/>Template:Rp The crankshaft, the earliest versions of which were forged alloy steel, had six throws but no counterweights, permitting a weight-saving of Template:Cvt.<ref name="knepperbook"/>Template:Rp

Each cylinder head has two overhead valves per cylinder activated through stamped-steel rocker arms and hydraulic tappets by pushrods that run through tubes below each cylinder barrel. The engine developed a reputation for leaking oil past the seals of the pushrod tubes. New seals of Viton solved the problem.<ref name="hemmings-feb2009"/><ref name="lvcc=may2017"/><ref name="startribune"/>

Viewed from the rear, the Corvair engine's crankshaft rotates counter-clockwise; opposite that of most other engines.<ref name="fiorebook"/>Template:Rp<ref name="tribune-25"/> This allows it to use regular transmission and pinion-gear arrangements when mounted in a rear-engine configuration.

Primary cooling is done by a shrouded cooling fan mounted horizontally on top of the engine. The fans were revised throughout the production run, with early fans made of steel and later ones of magnesium to reduce inertia. The fan is driven by a long V-belt from the back of the engine with an adjustable idler pulley. The belt makes two 90° turns to reach the fan resulting in four 90° twists. An early problem with the fan drive-belt jumping off the pulleys was solved by making the groove in the idler pulley deeper and adding belt guides. A metal bellows thermostat modulated either a ring valve on early engines or a set of damper doors on later ones to regulate the flow of cooling air.<ref name="knepperbook"/>Template:Rp

Engine oil is also used as a coolant. To remove heat from the oil the engine used a variety of types and sizes of oil coolers throughout its production run.<ref name="knepperbook"/>Template:Rp

Most Turbo-Air 6 engines use two one-barrel Rochester H carburetors; one per cylinder head. A later high-performance engine uses four carburetors; one Rochester HV primary and one Rochester H secondary per head. The secondary carb had no choke plate, idle circuit, accelerator pump, power circuit, or vapor vent.<ref name="carb-manual"/>Template:Rp

The arrangement of intake and exhaust valves in the Turbo-Air 6 is considered noteworthy, with the valves arranged as intake/exhaust, intake/exhaust, intake/exhaust down both sides.<ref name="knepperbook"/>Template:Rp The use of separate exhaust ports rather than twinned or siamesed ports helps avoid problems with distortion caused by a concentration of heat at these locations.<ref name="m-technic"/>

There is a single cast-iron camshaft located in the crankcase. The shaft has only nine cam lobes on it — the symmetrical arrangement of valves allows three double-width cam lobes to operate all six exhaust valves.<ref name="fiorebook"/>Template:Rp

TurbochargingEdit

File:Corvair turbo engine.jpg
Turbocharged Corvair engine

Chevrolet introduced a turbocharged version of the engine for the 1962 model year.<ref name="carbuzz"/> Development of this version was done by engineers James Brafford and Robert Thoreson, under the oversight of Bob Benzinger, who had become chief engine designer for the Corvair in 1959.<ref name="auwm-corvair"/> The turbocharged Corvair was released one month after the turbocharged Turbo-Rocket engine in the Oldsmobile F-85 Jetfire, making it just the second turbocharged car in volume production.<ref name="tc-23jan2015"/> This engine was not marketed under the Turbo-Air name, being listed initially as the Super Charged Spyder engine.<ref name="62-63-supplement"/>

Many of the internal components were strengthened or otherwise revised to deal with the stresses of forced induction. The engine received heavy-duty rod and main bearings, chromed upper piston rings, and nickel/chromium alloy exhaust valves. The crankshaft in the turbocharged engine was made of forged 5140 chrome-steel.<ref name="hemmings-nov2006"/> The compression ratio was reduced to the 8.0:1 of the original 1960 naturally aspirated engine.<ref name="knepperbook"/>Template:Rp The multiple-carburetor intake system was replaced with a single side-draft Carter YH carburetor.<ref name="hemmings-aug2004"/>

The turbocharger was made by the Thompson Valve Division of Thompson-Ramo-Wooldridge Inc., which became TRW in 1965.<ref name="howstuffworks"/> The model selected weighed Template:Cvt.<ref name="hemmings-nov2006"/> It had a Template:Cvt diameter impeller and was capable of spinning at up to 70,000 rpm.<ref name="hemmings-apr2015"/>

The turbocharged Corvair engine did not use a wastegate to limit boost pressure. Instead, boost was controlled by an exhaust system designed to create back-pressure sufficient to limit the maximum boost.<ref name="knepperbook"/>Template:Rp To prevent the engine from running too lean a metering rod and jet were selected that supplied an over-rich mixture when at full throttle.<ref name="macinnesbook"/> Static timing advance was set to 24° BTDC, with an additional 12° of centrifugal advance coming in above 4000 rpm. To prevent pre-ignition, a diaphragm on the distributor provided a pressure retard function rather than a vacuum advance, and could retard timing by up to 9° at manifold pressures above Template:Cvt.<ref name="autouniversum"/>

With maximum boost pressure limited to Template:Cvt, power output from this engine in 1962 was Template:Cvt, a 47% increase over the Template:Cvt output of the naturally aspirated engine. Torque was also increased by 58% to Template:Cvt.

Production run changesEdit

1960Edit

  • Engine debuts. Bore and stroke are Template:Cvt, for a total displacement of Template:Cvt. The compression ratio is 8.0:1, and power and torque outputs are Template:Cvt at 4400 rpm and Template:Cvt at 2400 rpm.
  • The 1960 engine has two carburetors, but a common air intake and filter with a single integrated automatic choke.<ref name="fiorebook"/>Template:Rp Air is fed to the carburetors through two large rubber hoses.
  • The cooling fan is Template:Cvt in diameter with 24 blades, and is made of steel.
  • Cooling airflow is controlled by a large-diameter bellows thermostat that drives a ring-shaped air valve in the eye of the blower.
  • The oil is cooled by a folded-fin cooler.
  • The engine does not have a harmonic balancer.
  • A high-output version of the engine called the "Special Camshaft package" is offered this year.<ref name="sci-may1960"/>Template:Rp This engine uses a different Rochester carburetor, a different camshaft profile with revised timing, and stiffer valve springs as well as a larger diameter exhaust system and a Delco-Remy ignition. Power output is up to Template:Cvt.<ref name="fiorebook"/>Template:Rp

1961Edit

  • Bore diameter in increased to Template:Cvt, raising engine displacement to Template:Cvt.<ref name="knepperbook"/>Template:Rp
  • A high performance Super Turbo-Air version is released. This engine includes a revised cylinder head and camshaft, with a compression ratio raised to 9.0:1.<ref name="fiorebook"/>Template:Rp Power is up to Template:Cvt at 4600 rpm and torque is up to Template:Cvt at 2800 rpm. Development was reportedly done by Zora Arkus-Duntov.
  • Engine cooling fan diameter is reduced to Template:Cvt with 16 vanes that extend right to the centre of the fan wheel.
  • The common intake with integrated choke is replaced by a shared air intake and manual chokes at each carburetor controlled by a pull-knob on the dashboard.<ref name="fiorebook"/>Template:Rp
  • Cooling is now controlled by a new set of damper doors at the lower part of each shroud actuated by small-diameter bellows thermostats.

1962Edit

1963Edit

  • Crankcase ventilation becomes standard.<ref name="fiorebook"/>Template:Rp
  • The folded-fin oil cooler is replaced with a 3-plate design on most cars and an 8-plate design on Spyders and cars equipped with air-conditioning.
  • Minor changes are made to the voltage regulator, distributor, cam profiles, and valves.

1964Edit

  • Displacement of naturally aspirated and turbocharged engines grows to Template:Cvt by increasing the stroke to Template:Cvt.<ref name="knepperbook"/>Template:Rp
  • Compression ratios are raised to 8.25:1 for the base and turbocharged engines, and to 9.25:1 for the high-performance engines.
  • Power and torque outputs rise to Template:Cvt at 3600 rpm and Template:Cvt at 2400 rpm for the base engine, Template:Cvt at 4400 rpm and Template:Cvt at 2800 rpm for the Super Turbo-Air engine. Peak power from the turbocharged engine is unchanged due to the carryover of the same turbocharger from 1962 and 1963, but arrives at 4000 rpm, and torque is Template:Cvt at 3200 rpm.<ref name="fiorebook"/>Template:Rp
  • The engine cooling fan is changed to a unit with 11 vanes and a diameter of Template:Cvt that is made of magnesium.
  • Air-conditioned cars and higher performance models receive a 12-plate oil cooler.
  • A harmonic balancer is added to the engine on all models except the base 95 hp engine.

1965Edit

  • The Template:Cvt engines are carried over essentially unchanged, with the exception of having an alternator instead of a generator.
  • A new naturally-aspirated version of the engine appears that produces Template:Cvt at 5200 rpm and Template:Cvt at 3600 rpm.<ref name="knepperbook"/>Template:Rp This engine has revised cylinder heads with larger valves, larger intake manifolds and exhaust port tubes, and a dual exhaust system.<ref name="fiorebook"/>Template:Rp The Template:Cvt engine also has four carburetors; two Rochester HV primaries and two Rochester H secondaries controlled by a progressive throttle linkage. The Template:Cvt engine also comes with the 12-plate oil cooler used on air-conditioned and turbocharged cars, and has the same forged chromium-steel crankshaft used in the turbocharged engine.
  • The turbocharged engine is fitted with a redesigned turbocharger with increased impeller dimensions, which increases maximum boost capacity to a level commensurate with the increased engine displacement that was introduced in 1964. Power is up to Template:Cvt at 4,000 rpm and Template:Cvt of torque at 3,200 rpm.<ref name="hemmings-aug2004"/><ref name="knepperbook"/>Template:Rp

1966Edit

  • The Template:Cvt engine receives a revised secondary linkage and cross-shaft for its four-carb setup.
  • All engines in cars sold in California, with the exception of turbocharged or air-conditioned versions, come equipped with Air Injection Reactors (AIR).<ref name="fiorebook"/>Template:Rp The system includes an air-injection pump and tubes, two mixture control valves, two check valves, and the requisite hoses. The distributor and carburetors are also specific to AIR-equipped engines.

1967Edit

  • All models sold in California come equipped with the AIR system. The package is available as an option in other regions.<ref name="fiorebook"/>Template:Rp
  • The Template:Cvt engine is dropped in early 1967, but reinstated later that year.
  • The Template:Cvt turbocharged engine is dropped from the lineup.

1968Edit

  • All US cars come equipped with the AIR system. Cylinder heads, exhaust manifolds, the distributor, and carburetors are all slightly changed to adapt to the AIR system.
  • Template:Cvt engine reinstated as a regular production option.<ref name="fiorebook"/>Template:Rp
  • The fuel system receives a vapor return line previously exclusive to the turbocharged engine.

1969Edit

  • No significant changes to the engine.

Experimental versionsEdit

Modular constructionEdit

In January 1960 Frank Winchell, who had a hand in adapting the Powerglide transmission to the Corvair, was made head of Chevrolet Engineering's Research and Development group.<ref name="cc-apr1995"/> In summer 1961 this group was working on two projects: the development of a counterpart to Ford's proposed Cardinal small car design and development of a second generation engine to succeed the Turbo-Air 6.<ref name="hemmings-fi"/> Among the goals for the new engine were increased horsepower, and elimination of some of the problems encountered with the original design, such as head-gasket failures and oil leaks.<ref name="curbside-modular"/>

Winchell first built an engine with displacement increased to Template:Cvt, but this only made the existing head-gasket problems worse. Winchell then proposed casting individual cylinder barrels and cylinder heads as a single piece, eliminating the head-gasket completely. A team was assembled that was led by Al Kolbe, who was responsible for the design of the original Turbo-Air 6. Heading up design for the new engine was Joe Bertsch, who was joined by engineers Len Kutkus and Jerry Mrlik. The engine they designed and developed kept the Turbo-Air 6 engine's boxer configuration and use of air cooling, and became known as the modular engine.

As with Winchell's earlier engine, bore and stroke were increased to Template:Cvt and Template:Cvt respectively.<ref name="cc-apr1995"/> The combined barrel-head was to be die-cast in aluminum with cast-iron cylinder liners. Each of these castings also included a channel for the pushrod path, doing away with the previous design's pushrod tubes. Valve covers were held in place by quick-release clips. Rather than use four long bolts per cylinder, the bottom of each cylinder barrel had a heavy flange which was bolted to the crankcase. The single horizontal cooling fan was replaced by three vertical fans on a common shaft.

Problems with heat-distortion of the early alloy cylinder barrel/head units led to a subsequent redesign that included cooling fins angled at 45° to eliminate cutouts needed for access to the bolts holding the barrels to the crankcase, and the reintroduction of push-rod tubes.

The engine was "modular" in that the individual cylinder/head units allowed Chevrolet to design engines with 2, 4, 6, 8, 10, and 12 cylinders, of which versions with 2, 4, 6 and 10 cylinders were built. The 6 cylinder version produced about Template:Cvt and was tested in a Corvair, while 2 and 4 cylinder engines were installed in a Renault Caravelle and two Alfa Romeo Giuliettas. The 10 cylinder version was called P-10 and was installed in a 1962 Chevrolet Impala converted to front-wheel drive. This engine produced Template:Cvt. Design project XP-790 was originally meant to be the basis for a front-wheel drive replacement for GM's E-body cars, and incorporate flat-10 engines based on the P-10. Project XP-787 was split off from XP-790 to allow further development, while XP-790 was returned to the Research Studio, where it became the basis for the Firebird IV concept car. Project XP-787 was cancelled. Engines with 8 and 12 cylinders were designed but not built.

A private Corvair owner bought a collection of engines and parts and installed a running modular engine in his personal car.<ref name="lvcc-jul2016"/>

Overhead camshaftsEdit

Chevrolet developed a prototype of the Turbo-Air 6 with a single overhead camshaft (SOHC) in each cylinder head.<ref name="vegasvairs-sohc"/> This was during the time from 1964 to 1966, with the SOHC project lagging the modular engine by approximately a year.

The camshafts were driven off the crankshaft by a timing belt. The valves were operated through rocker arms. The engine used three cooling fans, each directing air to one pair of opposed cylinders. The air/fuel intake used one Chevrolet-designed three-barrel carburetor per side. The original Template:Cvt stroke was retained while the bore was increased to Template:Cvt, giving a total displacement of Template:Cvt. The pistons were a pent-roof type, and the combustion chamber shape approximated a hemisphere. The compression ratio was 10.5:1. While claimed output was as high as Template:Cvt at 7200 rpm, none of the three prototype engines developed more than Template:Cvt at 5700 rpm and Template:Cvt at 5200 rpm.

In the Chevrolet Final Report on the engine written 22 February 1966, the need for improvements in cooling was highlighted. Power losses to the cooling fan was reported to be Template:Cvt at 6000 rpm and was expected to nearly double at the engine's redline, bringing useful power down to the vicinity of the naturally aspirated Template:Cvt engine.

One of the SOHC engines was displayed alongside the Astro I concept car, although it is reported that it was never installed in the car.<ref name="lvcc-aug2016"/> All three prototype engines are believed to have been destroyed.

Fuel injectionEdit

General Motors began investigating the use of fuel injection on the Turbo-Air engine on 11 August 1962.<ref name="vv-dec2008"/> A mechanical injection system made by the Marvel Schebler division of BorgWarner was installed on a pre-production Template:Cvt engine. The engine received Bill Thomas 4X1 cylinder heads with larger valves; Template:Cvt intake and Template:Cvt exhaust. A camshaft from Iskendarian provided high-lift and longer duration. After the initial feasibility study serious development started on 12 February 1963.

Extensive testing of intake systems was done. Eventually the team settled on Template:Cvt diameter ram tubes each Template:Cvt long and a central plenum. This configuration was tested against both a 1963 and 1964 turbo engine as well as engines with six individual carburetors and two three-barrel Webers. The injected engine's output of Template:Cvt was higher than both turbos but lower than either carbureted engine. Road testing of the injected engine began on 19 April 1963.

In May 1963 a new injection system designed by Rochester was installed that produced nearly the same output as the Marvel-Schebler system. Performance of the most recent development engine was compared with a 4X1 Template:Cvt engine on 5 November 1963; the injected engine produced approximately Template:Cvt more. Another extensive road-test evaluation began on 15 November 1963. During October and November 1964 four more injected engines were built, one of which underwent road testing. By 2 February 1965 the injected engine was producing Template:Cvt gross and Template:Cvt net. On 24 February 1965 a final lab comparison was run, that concluded the 30-month development program. The extra cost of fuel injection could not be justified based on the power gains achieved.

Some versions of the Yenko Stinger were available with fuel injection.<ref name="cc-v4n2"/> This system was based on GM's work.<ref name="org-fi"/>

Water-coolingEdit

While not a Chevrolet project, at least one water-cooled Turbo-Air 6 was built by independent engine designer Lloyd Taylor.<ref name="cc-nov1981"/>

Other applicationsEdit

Apart from the production Corvair models, the Turbo-Air 6 engine was used in a variety of other applications.

Prototypes and styling exercisesEdit

Both General Motors and some major carrozzeria have used the engine in several Corvair-based concept and show cars.

  • Corvair Monza — The first Corvair Monza was a Show car that pre-dated the production Monza.<ref name="knepperbook"/>Template:Rp This two-door coupe was first seen at the Chicago Auto Show.
  • Corvair Super Monza — Mechanically unmodified, the Super Monza was an exercise ordered by Bill Mitchell that saw a 900 coupe fitted with a luxurious interior and special exterior paint and trim, including a sunroof and wire wheels.<ref name="mt-aug1960"/> It debuted at the 1960 New York Auto Show.
  • XP-709 "Pinky" — The first Corvair convertible, this car was eventually given to Harley J. Earl's wife Sue.<ref name="automag1"/><ref name="psauto"/>
  • Pontiac Polaris — This version of the Corvair carried a Pontiac badge and modified bodywork. It reached prototype stage before being cancelled.<ref name="ca-feb1987"/>
  • Sebring Spyder Coupe — This concept was powered by a 145-horsepower engine with four carburetors.<ref name="knepperbook"/>Template:Rp
  • XP-737 Sebring Spyder roadster. The original engine in this short-wheelbase concept had a Paxton supercharger.<ref name="knepperbook"/>Template:Rp It was later converted to a turbocharged engine.
  • XP-785 Corvair Super Spyder — Another short-wheelbase special, this car also had revised front bodywork, and a turbocharged engine.<ref name="knepperbook"/>Template:Rp
  • XP-777 Chevrolet Corvair Monza GT — This project mounted the engine amidships.<ref name="knepperbook"/>Template:Rp Over time it received a variety of engines, including a Template:Cvt version and one with twin-turbochargers.
  • XP-797 Chevrolet Corvair Monza SS — The SS kept the engine behind the rear wheels, and added six Dell'Orto carburetors.
  • XP-842 Chevrolet Astro I — An extremely low show car designed by Larry Shinoda under the direction of Bill Mitchell, the Astro I was built to use a rear-mounted engine and was displayed alongside the SOHC prototype engine.<ref name="motor1-astro1"/><ref name="hemmings-dec2005"/>
  • XP-849 Corvair II — This GM styling exercise first appeared in May 1965. XP-849 was turned over to the Research Studio at the end of 1965. A revised car appeared in June 1966, but the project was cancelled by June 1967. No engine was specified but some body features suggested that a rear-engined configuration was still being considered.
  • Chevrolet Corvair Speciale by Pininfarina — Pininfarina first showed a Corvair-based coupe in 1960, and a 2+2 version later.<ref name="knepperbook"/>Template:Rp
  • Chevrolet Testudo — Built by Bertone. The Testudo was designed by Giorgetto Giugiaro, and used the factory power-train in a shortened chassis.

Specialist CorvairsEdit

Some companies modified stock Corvairs to create vehicles that offered improved performance or individualized appearance that were sold under the customizers' or parts suppliers' names.

  • Yenko Stinger — Don Yenko built 100 modified Corvairs with the rear seats removed to qualify it as a sports car for SCCA racing in 1966.<ref name="c-and-d-jun1966"/> The SCCA put the car in Class D. Stingers were available in several stages of tune, including Stage I (Template:Cvt), Stage II (Template:Cvt), Stage III (Template:Cvt), and Stage IV (Template:Cvt).<ref name="hemmings-yenko"/> Production ran from 1966 through 1969.<ref name="ys-archives"/>
  • Fitch Sprint — A Fitch Sprint could be bought directly from John Fitch's works in Connecticut, or the parts to complete one ordered as a dealer-installed option.<ref name="hemmings-sprint"/> Engines in early cars received a Fitch-developed four-carburetor intake, while later cars used the factory four-carb setup but with other modifications. Power was raised to a peak of Template:Cvt.<ref name="fitch-bio"/>
  • Solar Sprint and Solar Cavalier — Built by Solar Automotive. In the 1970s John Fitch sold his remaining Fitch Sprint parts inventory and that part of his business to Art Hershberger of Princeton, Wisconsin.<ref name="hemmings-sprint"/> Herschberger resumed production of the Sprint and launched the Cavalier model. Solar models continued to use Fitch's carburetor modifications as well as offering a Weber conversion.<ref name="tca-nov1999"/><ref name="corsa-concours"/>
  • IECO Corvair — IECO was a major aftermarket parts supplier. Among other items, IECO offered a four-barrel "Ram induction" carburetor conversion intake manifold for the Corvair engine.<ref name="cl-sep1965"/>
  • EMPI Corvair- EMPI was a major aftermarket parts supplier that offered a camber-compensator for the Corvair, as well as performance equipment including intake and exhaust systems.<ref name="cl-sep1963"/>
  • Eshelman Golden Eagle — Built by Cheston Lee Eshelman's company, this car was a standard Corvair with some superficial cosmetic customization.<ref name="hemmings-ege"/> The engine was unmodified.
  • Lost Cause — Commissioned by Charles Peaslee Farnsley, with bodywork and trim by the Derham Body Company, the Lost Cause was a Corvair converted into a luxurious personal limousine.<ref name="fcg-sep1963"/>Template:Rp It debuted at the 1963 New York Auto Show.<ref name="sfba1"/> The engine was reported to have received a Fitch four-carb conversion.<ref name="chitrib"/>

Hot rods and custom carsEdit

Private hot rodders and a few small companies built one-off cars, some intended for series production that never materialized, that used the Turbo-Air 6 engine.

  • Can Am 1 — Produced by the Bolide Motor Company, this Corvair-powered prototype is believed to be a development of the AMT Piranha.<ref name="beaulieu-canam1"/>Template:Rp A project of Jack Griffith and Borg-Warner, the car was shown at the 1969 New York Auto Show. A later version was to have been powered by a Ford V8. The car did not go into production.
  • Claymobile — A custom-bodied Corvair that was reported to have been either a tribute to or commission from boxer Muhammud Ali. Its name referred to Ali's birth name of Cassius Clay.<ref name="autopasion"/><ref name="junkyard1"/>
  • Corphibian — GM engineers Richard E. Hulten and Roger D. Holm developed an amphibious Forward Control truck.<ref name="r&t-corphibian"/> They formed Hulten-Holm and Company, and tried to get GM to put it into production.<ref name="hemmings-corph"/> A fiberglass undertray was fitted to seal the undercarriage of the one prototype built, and the rear of the truck was extended by Template:Convert to make room for the hydraulic reservoir and motors needed to drive the propellers, powered by a hydraulic pump driven off the Turbo-Air 6 engine. The Corphibian did not go into production.
  • Corsetta — A BMW Isetta microcar powered by a Corvair Turbo-Air 6 engine.<ref name="hr-corsetta"/>
  • Corvair Futura — This custom forward-control station wagon with center-steering was built by Henry Larson of New Brighton, Minnesota.<ref name="lseel-dec2012"/> It was inspired by a sketch of a car called the Waimea done by Rhys Miller, which was one of several designs Miller did for the Kaiser Aluminum company to promote the use of aluminum in automobiles.<ref name="jacg-futura"/> While the Waimea was intended to be front-wheel drive, the Futura retains the rear-engine, rear-wheel drive location of the Turbo-Air 6 engine from the Corvair Greenbriar van that it was based on. The car was purchased by Wayne Carini.
  • Devin GT — Developed by Devin Enterprises, the company founded by Bill Devin, this Corvair-powered coupe was meant to go into production after the Devin C, but only appeared in prototype form.
  • Fitch Phoenix — Built by John Fitch. This custom-bodied car was built on a Corvair chassis whose wheelbase had been shortened to Template:Cvt.<ref name="knepperbook"/>Template:Rp Weight was reduced to Template:Cvt. The car started out as a 1965 Monza coupe. The engine code listed for the car when at auction in 2014 indicates that the unit installed was a Template:Cvt engine originally making Template:Cvt.<ref name="bonhams-phoenix"/> Power was boosted to Template:Cvt.<ref name="hemmings-phoenix"/> The bodywork was done in steel by Intermeccanica.
  • Forcasta — A bubble-car built by Darryl Starbird in 1961, this car was based on a 1960 Corvair and engine with a heavily customized steel body. The engine was stock, but steel parts were chrome-plated and alloy parts were polished.<ref name="knepperbook"/>Template:Rp<ref name="hrm-forcasta"/>
  • Forton Track T — A mid-engined, Turbo-Air 6 powered track-style T roadster built by Bill Forton.<ref name="corvairs-forton"/>
File:Reactor by Gene Winfield.jpg
Reactor by Gene Winfield
  • Hannibal Twin-8 — Five copies were built for the movie The Great Race. Two were driveable, and of these one was powered by a Corvair flat-six engine. All four rear wheels are driven via chain drive.<ref name="hemmings-hannibal"/><ref name="jacg-hannibal"/>
  • Molzon Concept Corsa GT 38 — Designed and built by GM designer Bill Molzon, this car had a four-carb Turbo-Air 6 engine mounted amidships driving through a Porsche transaxle. The car weighed just Template:Cvt. It was sold at auction on 18 January 2018.<ref name="lvcc-dec2017"/>
  • Reactor — Built by Gene Winfield.<ref name="lvcc-apr2016"/> Winfield partnered with Ben Delphia on the design. Bodywork was done in aluminum.<ref name="automag-jun2017"/> The car used a turbocharged Corvair engine mounted in the front and driving the front wheels, using a modified Citroën DS chassis, including the Hydropneumatic suspension. This car appeared on the television programs Bewitched, Star Trek: The Original Series, and Batman (TV series).<ref name="automag-jun2017"/>
  • Road Agent — A mid-engined bubble-car built by Ed "Big Daddy" Roth.<ref name="thackerbook"/>Template:Rp<ref name="lvcc-sep2011"/>Template:Rp Roth installed the Turbo-Air 6 engine ahead of the rear wheels in a custom chassis of 4130 tubing with the 2-speed automatic transaxle mounted upside-down to provide the proper rotation.
  • Silhouette II Space Coupe — A Corvair-powered bubble-car built by Bill Cushenbery.<ref name="hemmings-oct2017"/> An early Corvair engine was installed in a custom chassis with an aluminum superleggera body. The original engine was later replaced by a 1965 Template:Cvt model.
  • Stiletto — A Corvair-powered bubble-car commissioned by Bob Larivee, designed by Gene Baker, and built by Ron Gerstner.<ref name="vetteworld"/> Stiletto debuted at the 1966 Detroit Autorama show and was featured in the July 1966 issue of Car Craft magazine.<ref name="ahrf1"/>
  • T-bucket — A front-engined Corvair-powered hot rod built by Don Kendall.<ref name="ahrf2"/> This car was featured on the cover of Rod Action magazine in November 1973. It also won "Best Engineered Rod" at the 1973 NSRA NATS in Tulsa, Oklahoma.

Limited-production automobilesEdit

Some smaller manufacturers used the engine in limited-production cars, some with heavily modified Corvair chassis and some with fully custom frames.

  • AMT Piranha & Centaur Engineering CRV-II through CRV-V sports racer — Initially commissioned by Marbon Chemicals and designed by Dann Deaver of Centaur Engineering as the CRV. These cars were meant to showcase ABS plastic-bodied cars. With the exception of the first CRV prototype and the Piranha dragster, all were powered by the Chevrolet flat-six engine,<ref name="lvcc-mar2011"/><ref name="cdn-piranha"/><ref name="Whitlow"/> Aluminum Model Toys, commonly abbreviated as AMT, re-engineered the CRV, called it the Piranha, fitted it to a modified Corvair chassis, and offered it for sale as a kit. The work was done at AMT's Speed and Custom Division headed by Gene Winfield. AMT offered the car with the option of either a Template:Cvt engine.<ref name="hr-jan2005"/> In 1967, the AMT Piranha appeared on the Man from U.N.C.L.E. television series.<ref name="Whitlow"/>
  • Cord 8/10 Sportsman — Built by the Cord Automobile Company, established by Glen Pray. A 4/5 scale replica of a Cord 810 powered by either a Template:Cvt Corvair engine in a front-wheel-drive layout. 6 prototypes and 91 production cars were built until the company was shuttered. Production was restarted by SAMCO, who built an additional 14 cars, 12 of which continued with Corvair power.<ref name="corvairgold"/><ref name="lvcc-dec2016"/>
  • Devin C — Built by Devin Enterprises. The car was based on the earlier, VW or Porsche-powered Devin D.
  • Fiberfab Azteca — A further development of Fiberfab's earlier Aztec model, the 1965–66 Azteca included a custom chassis that allowed it to install the Corvair pancake engine ahead of the rear wheels.<ref name="dt-aug2020"/> Three are reported to have been built.<ref name="osr-azteca"/> A restored, customized Azteca appeared at the 2013 SEMA show with a supercharged Corvair engine said to develop in the range of Template:Cvt.<ref name="cd-nov2013"/>
  • Fiberfab Avenger GT-15 — A kit-car with a GT40-influenced body built specifically to use the Corvair drive-train including its rear-mounted Turbo-Air 6 engine.<ref name="lvcc-sep2015"/><ref name="fiberclassics-gt15"/>

On-road race carsEdit

The Turbo-Air 6 powered several cars of different types that were purpose-built to be raced on pavement.

  • Bobsey SR-3 — Chassis SR3-004, originally built by Gerald Mong for driver Chuck Dietrich, was fitted with a Corvair engine in a special wide chassis.<ref name="bobsey1"/>
  • Huffaker Genie MkV — Chassis H-005 was built to accept a Corvair engine.<ref name="genie1"/>
  • LaBoa — A custom-built car commissioned by attorney Herbert W. Cox. Construction was done by Fitzgerald Machine Shop in Greenville, Ohio. The Corvair-powered car was raced throughout the 1960s before being garaged in 1967. The LaBoa was eventually sold and restored.<ref name="lvcc-feb2016"/><ref name="sportsracernet"/>
  • Levair Velociraptor — Built by Warren LeVeque, owner of LeVair Performance Products.<ref name="indyscca1"/><ref name="autoxer-solo1"/> The car was built from parts from a Formula Saab. The engine was enlarged to Template:Cvt, and developed Template:Cvt. LeVeque sold the car and bought it back at a later date. Several members of the LeVeque family have raced the Velociraptor.
  • Lola T320 — Built by Seth Emerson, the car started as pre-1976 Formula Vee chassis #19 and was lengthened by Template:Cvt to make room for the longer Corvair engine.<ref name="formulacar1"/> A Crown Manufacturing adapter plate mated the engine to the Lola's Hewland transaxle. The engine was turbocharged.
  • E-Econo class dragster — The owner and engine builder was Ray Clayton. The chassis was built by Kenny Bowers at Advanced Chassis.<ref name="tca-dragster1"/>
  • Silver Fox — An autocross car that was originally built by Brian Harding, the car was first sold to Gary Bailey and eventually to Dan Cole.<ref name="lvcc-may2016"/> As part of restoring the car Cole had the engine bored and rebuilt by Bill Bamford.

MotorcyclesEdit

Several Corvair-powered motorcycles have been built by individual fabricators and bike shops. Some of the most well-known are listed below.

  • Corvair Trike — Built by Tom McMullen of AEE Choppers.<ref name="scw1"/>
  • Grasshopper — Built by "Wild" Bill Gelbke.<ref name="grasshopper"/>
  • Six-Pack — Built by Norm Grabowski.<ref name="sixpack"/>

Off-road vehiclesEdit

  • Manx-Vair and the Queen Manx — Actor Steve McQueen contracted off-road expert Pete Condos and his company Con-Ferr engineering to build a special car for the 1968 "The Thomas Crown Affair" movie.<ref name="zimmbook"/>Template:Rp Starting with a standard Meyers Manx, Condos and his staff modified the body and installed a 140-horsepower four-carburetor Corvair engine in the car to create the "Queen Manx". Con-Ferr and Meyers went on to build over 50 copies, called the "Manx-Vair".<ref name="sema1"/> The car was later revived as the Hunter Buggy by Universal Fiberglass.<ref name="bangshift1"/>
  • Deserter GS — Sold by Dearborn Automobile Company Inc., much of the engineering was done by a company called Autodynamics, which shared shop space with Dearborn Automobile. Autodynamics background building successful Formula Vee cars (based on the 1963 Volkswagen Beetle) was reflected in the custom tubular chassis and VW-based suspension of the car. The Deserter GS was a mid-engined car, with a long-wheelbase that allowed the Turbo-Air 6 engine to be mounted ahead of the rear wheels.<ref name="lvcc-apr2014"/>Template:Rp<ref name="lvcc-oct2015"/><ref name="dearbornauto"/>
  • Bugetta — A rear-engined Buggy built by veteran Indianapolis and Group 7 car builder Jerry Eisert and his company, Eisert Racing Enterprises. The Corvair engine was mounted in a unique monocoque chassis.<ref name="halehandbook"/>Template:Rp
  • Trail Blazer — A four-wheel drive car designed by Vic Hickey of the Hickey Manufacturing Company, it is powered by a Corvair engine. The engine is mounted behind the front wheels in a front-mid-engine arrangement. Engine power goes back through a Borg-Warner three-speed transmission to a transfer case that corrects for engine rotation and sends power to the front and rear differentials.<ref name="mt-jul1961"/><ref name="fw-jan1964"/> General Motors bought the rights to the car, and hired Hickey. The Trail Blazer is considered by some to be the forerunner to the Chevrolet Blazer.<ref name="bj-lot256"/>

Volkswagen conversionsEdit

Several options existed for adapting the Turbo-Air 6 engine to the transaxle in Volkswagen-based cars, or to fit a complete Corvair power-train into a modified VW chassis.

  • Crown Manufacturing — Sold adapters that allowed the Corvair engine to bolt directly up to a Volkswagen transaxle. This conversion required either flipping the pinion over to the other side of the transaxle case (on swing-axle VWs) or installing a Crown-supplied reverse-rotation camshaft (for IRS VWs) to compensate for the rotation of the Corvair engine.<ref name="fisherbook"/>
  • Hadley Engineering — Developed a kit sold under the name "Trans-Vair". This product included a full sub-frame that allowed a complete Corvair powertrain to be installed in a modified Volkswagen chassis.<ref name="transvair"/>
  • Lukes and Shorman — One of the first companies to offer a kit to adapt the Turbo-Air 6 to a Volkswagen transaxle.<ref name="lvcc-sep2018"/> Lukes and Shorman produced an adapter plate of cast aluminum to mate the engine to the transaxle. The need to machine the flywheel end of the crankshaft was avoided by the use of a Porsche flywheel with a steel plate drilled to the Corvair bolt pattern welded into its centre. The clutch used was a VW commercial disc mated to the diaphragm pressure plate from a Porsche Carrera. Engine rotation was compensated for by flipping the ring gear to the other side of the transaxle. A revised starter was needed, and the early engines were converted to 6 volt operation to make them compatible with the electrical systems on early Volkswagens.

MotorhomesEdit

  • Travalon and UltraVan — Aircraft designer David Peterson created this monocoque-framed motorhome, built using aircraft methods.<ref name="ultravan1"/> The early Travalon models built by the Prescolite Corporation were used as mobile showrooms. The UltraVan models were built by Ultra Inc. The vehicles were powered by either the Template:Cvt or, later, an optional Template:Cvt version of the Corvair flat-six engine. Weighing about Template:Cvt, the Ultravan could cruise at Template:Cvt and return fuel economy in the range of Template:Cvt.<ref name="cc-ultravan"/>

MilitaryEdit

  • Canadair CL-91 / DynaTrac XM-571 — A two-body amphibious track vehicle, the CL-91/XM-571 was powered by an industrial version of the Turbo-Air 6.<ref name="casr1"/><ref name="bf-xm571"/>
  • AGL-4 — The Articulated General Purpose Logistical Truck was a prototype vehicle produced by GM Defense Research Laboratories.<ref name="autoweek-agl4"/> Powered by a Corvair flat-six engine, the AGL-4 had an articulated joint between the cab and bed that allowed the two to rotate with respect to each other. It did not reach production.
  • Gama Goat XM561 — Designed by Roger Gamaunt and built by the Chance-Vought Aircraft company, the Gama Goat was a six-wheel drive military vehicle with four-wheel steering and an articulated body.<ref name="sgamaa"/> A Turbo-Air 6 engine powered two of the earliest prototypes, but was replaced by a Detroit Diesel 53 engine in the production version, which had the designation M561.
  • XM-808 Twister — Built by Lockheed Ground Vehicles, the first prototype of this eight-wheeled dual-body military off-roader used two Template:Cvt Corvair engines — one in front and one in back — to propel the vehicle.<ref name="hemmings-twist"/><ref name="ps-aug1968"/>

MarineEdit

  • Wayne 100 inboard marine engine — This was a version of the Corvair pancake six engine adapted to marine use by Wayne F. Horning and his company, Inboard Marine.<ref name="marinepatent"/> The engine was installed vertically, flywheel end up, and drove a lower unit that went through the bottom of the hull. The engines were first put in 16 foot Glasspar Avalons, and later in Tahiti hulls.

Scientific prototypesEdit

  • MGL/MOLAB — The Mobile Geological Laboratory was a test platform for lunar exploration powered by a modified Corvair engine. The vehicle was designed and built by Vic Hickey while at General Motors.<ref name="hemmings-nov2012"/><ref name="vox-lunar"/>

AircraftEdit

File:PantherLSA.jpg
A Sport Performance Aviation Panther airframe under construction, fitted with a Corvair engine

The air-cooled Corvair engine has been widely used in homebuilt aircraft. Some aircraft, such as the Pro-Composites Personal Cruiser have been specifically designed for them.<ref name="WDLA11"/> The defunct American company Hegy Propellers, which was based in Marfa, Texas, produced propellers specifically for Corvair engines.<ref name="Aerocrafter"/>

A variation on the six-cylinder engine is an opposed-twin version based on the Corvair pancake six.<ref name="tca"/><ref name="ultraligero"/> Some individuals have also experimented with inline-triple configurations based on half of a Turbo-Air six.<ref name="fly-news"/>

Aircraft applicationsEdit

Engine Serial Number CodesEdit

The following codes (last two characters of engine serial number) identify the year, size, power, and transmission of the engine<ref name="tca-codes"/>

Template:Columns-list

Terms
  • A/C — Air Conditioning
  • AIR — Air Injection Reactor
  • A/T — Automatic Transmission
  • HPE — High Performance Engine
  • P/G: Power-Glide automatic transmission.
  • SHPE — Special High Performance Engine
  • T/C — Turbo-Charged
Engine & Options<ref name="fiorebook"/>Template:Rp Model Series 1960 1961 1962 1963 1964 1965 1966(9) 1967(9) 1968(10) 1969(10)
80 hp, 3-speed 500/700/900 Y - - - - - - - - -
80 hp, MT 3 or 4-spd 500/700/900 except SW - Y(1), YC(2) YC YC - - - - - -
80 hp, AT 500/700 except SW Z Z Z Z - - - - - -
80 hp, MT, AC 500/700/900 except SW - YL(4) YL YL - - - - - -
80 hp, AT, AC 500/700 except SW - ZD(4) ZD ZD - - - - - -
80 hp, MT 3 or 4-spd., SW 535/735 - YF(1),YH(2) YH YH - - - - - -
80 hp, AT, SW 535/735 - ZB ZB - - - - - - -
80 hp, MT, FC FC - V V V - - - - - -
80 hp, AT, FC FC - W W W - - - - - -
80 hp, MT, FC, Export version FC - - VA VA - - - - - -
80 hp, AT, FC, Export version FC - - WA WA - - - - - -
80 hp, AT, Monza only 900 except SW Z Z(1)ZH(7) - - - - - - - -
84 hp, AT, Monza only 900 except SW - - ZH ZH - - - - - -
80 hp, AT, AC, Monza only 900 except SW - ZJ(4)(7) - - - - - - - -
84 hp, AT, AC, Monza only 900 except SW - - ZJ ZJ - - - - - -
84 hp, AT, SW, Monza only 935 - - ZL - - - - - - -
95 hp, 140 CID, 3-spd 500/700/900 YA(1)YB(2) - - - - - - - - -
95 hp, 140 CID, 4-spd 500/700/900 YD - - - - - - - - -
95 hp, 164 CID, MT 500/700/900 - - - - YC - - - - -
95 hp, 164 CID, AT 500/700/900 - - - - Z - - - - -
95 hp, 164 CID, MT, AC 500/700/900 - - - - YL - - - - -
95 hp, 164 CID, AT, AC 500/700/900 - - - - ZD - - - - -
95 hp, 164 CID, MT, FC FC - - - - V - - - - -
95 hp, 164 CID, AT, FC FC - - - - W - - - - -
95 hp, 164 CID, MT, FC, Export version FC - - - - VA - - - - -
95 hp, 164 CID, AT, FC, Export version FC - - - - WA - - - - -
98 hp, MT, 8.0:1 CR 500/700/900 except SW - YD(5) - - - - - - - -
98 hp, MT, 9.0:1 CR 500/700/900 except SW - YN(5) - - - - - - - -
98 hp, AT, 8.0:1 CR 500/700/900 except SW - ZD(3)(8) - - - - - - - -
98 hp, AT, 9.0:1 CR 500/700/900 except SW - ZF(3) - - - - - - - -
98 hp, MT, 8.0:1 CR, SW 535/735 - YJ(5) - - - - - - - -
98 hp, MT, 9.0:1 CR, SW 535/735 - YQ(5) - - - - - - - -
98 hp, AT, 8.0:1 CR, SW 535/735 - ZE(3) - - - - - - - -
98 hp, 9.0:1 CR, SW 535/735 - ZK(3) - - - - - - - -
98 hp, MT, 9.0:1 CR, AC 500/700/900 except SW - YM(4) - - - - - - - -
98 hp, AT, 9.0:1 CR, AC 500/700/900 except SW - ZG(4) - - - - - - - -
102 hp, MT 500/700/900 except SW - - YN YN - - - - - -
102 hp, AT 500/700/900 except SW - - ZF ZF - - - - - -
102 hp, MT, AC 500/700/900 except SW - - YM YM - - - - - -
102 hp, AT, AC 500/700/900 except SW - - ZG ZG - - - - - -
102 hp, MT, SW 535/735 - - YQ - - - - - - -
102 hp, AT, SW 535/735 - - ZK - - - - - - -
110 hp, MT 500/700/900 - - - - YN - - - - -
110 hp, AT 500/700/900 - - - - ZF - - - - -
110 hp, MT, AC 500/700/900 - - - - YM - - - - -
110 hp, AT, AC 500/700/900 - - - - ZG - - - - -
110 hp, MT, FC FC - - - - VB - - - - -
110 hp, AT, FC FC - - - - WB - - - - -
150 hp, MT, TC, Spyder 927-967 - - YR YR - - - - - -
150 hp, MT, TC, Spyder 627-667 - - - - YR - - - - -
95 hp, MT - - - - - - RA RA RA - -
95 hp, AT - - - - - - RG RG RG - -
95 hp, MT, AC - - - - - - RE RE RE - -
95 hp, AT, AC - - - - - - RJ RJ RJ - -
95 hp, MT, AIR - - - - - - - RS RS RS AC
95 hp, AT, AIR - - - - - - - RV RV RV AE
95 hp, MT, AIR, AC - - - - - - - - QM - -
95 hp, AT, AIR, AC - - - - - - - - QO - -
95 hp, MT, RC - - - - - - RS - - - -
95 hp, AT, FC - - - - - - RV - - - -
110 hp, MT - - - - - - RD RD RD - -
110 hp, AT - - - - - - RH RH RH - -
110 hp, MT, AC - - - - - - RF RF RF - -
110 hp, AT, AC - - - - - - RK RK RK - -
110 hp, MT, AIR - - - - - - - RU RU RU AD
110 hp, AT, AIR - - - - - - - RW RW RW AF
110 hp, MT, AIR, AC - - - - - - - - QS - -
110 hp, AT, AIR, AC - - - - - - - - QP - -
110 hp, MT, FC - - - - - - RU - - - -
110 hp, AT, FC - - - - - - RX - - - -
140 hp, MT, except Corsa - - - - - - RM RM (6) - -
140 hp, AT, except Corsa - - - - - - RN RN (6) - -
140 hp, MT, AC, except Corsa - - - - - - - RZ - - -
140 hp, AT, AC, except Corsa - - - - - - - RY - - -
140 hp, MT, AIR, except Corsa - - - - - - - RQ (6) RY AG
140 hp, AT, AIR, except Corsa - - - - - - - RX (6) RZ AH
140 hp, MT, Corsa only - - - - - - RB RB - - -
140 hp, MT, AC, Corsa only - - - - - - - RR - - -
140 hp, MT, AIR, Corsa only - - - - - - - RT - - -
180 hp, MT, TC, Corsa only - - - - - - RL RL - - -
Notes:
(1) — Early year code
(2) — Late year code
(3) — CR change from 8.0:1 to 9.0:1 with engine #T0207. ZD suffix changes to ZF, ZE to ZK.
(4) — AC introduced mid-1961 model year.
(5) — CR change from 8.0:1 to 9.0:1 with engine #T0109. YD suffix changes to YN, YJ to YQ.
(6) — Likely the same as previous year.
(7) — CR change from 8.0:1 to 9.0:1 mid-1961. Z suffix changes to ZH.
(8) — ZD used again with introduction of AC
(9) — AIR mandatory in California for 1966 and 1967, except on 180 hp and AC cars in 1966.
(10) — AIR standard on all 1968 and 1969 cars.
Abbreviations:
AC — Air Conditioning
AIR — Air Injection Reactor
AT — Automatic Transmission (Powerglide)
CID — Cubic Inches Displacement
CR — Compression Ratio
FC — Forward Control (Greenbrier, Corvan, Loadside, Rampside)
MT — Manual Transmission (3-speed or 4-speed)
SW — Station Wagon (Corvair or Lakewood)
TC — Turbo-Charged

See alsoEdit

ReferencesEdit

Template:Sister project Template:Reflist

Retrieved from "https://zalansite.site/mediawiki/index.php?title=Chevrolet_Turbo-Air_6_engine&oldid=789137"