Standard molar entropy

Template:LaymanTemplate:Short description In chemistry, the standard molar entropy is the entropy content of one mole of pure substance at a standard state of pressure and any temperature of interest. These are often (but not necessarily) chosen to be the standard temperature and pressure.

The standard molar entropy at pressure = <math>P^0</math> is usually given the symbol Template:Mvar, and has units of joules per mole per kelvin (J⋅mol⁻¹⋅K⁻¹). Unlike standard enthalpies of formation, the value of Template:Mvar is absolute. That is, an element in its standard state has a definite, nonzero value of Template:Mvar at room temperature. The entropy of a pure crystalline structure can be 0Template:NbspJ⋅mol⁻¹⋅K⁻¹ only at 0Template:NbspK, according to the third law of thermodynamics. However, this assumes that the material forms a 'perfect crystal' without any residual entropy. This can be due to crystallographic defects, dislocations, and/or incomplete rotational quenching within the solid, as originally pointed out by Linus Pauling.<ref>Template:Cite book</ref> These contributions to the entropy are always present, because crystals always grow at a finite rate and at temperature. However, the residual entropy is often quite negligible and can be accounted for when it occurs using statistical mechanics.

Thermodynamics

If a mole of a solid substance is a perfectly ordered solid at 0Template:NbspK, then if the solid is warmed by its surroundings to 298.15Template:NbspK without melting, its absolute molar entropy would be the sum of a series of Template:Mvar stepwise and reversible entropy changes. The limit of this sum as <math>N \rightarrow \infty </math> becomes an integral:

<math>S^\circ = \sum_{k=1}^N \Delta S_k = \sum_{k=1}^N \frac{dQ_k}{T} \rightarrow \int _0 ^{T_2} \frac{dS}{dT} dT = \int _0 ^{T_2} \frac {C_{p_k}}{T} dT</math>

In this example, <math>T_2 =298.15 K </math> and <math>C_{p_k}</math> is the molar heat capacity at a constant pressure of the substance in the reversible process Template:Mvar. The molar heat capacity is not constant during the experiment because it changes depending on the (increasing) temperature of the substance. Therefore, a table of values for <math>\frac{C_{p_k}}{T}</math> is required to find the total molar entropy. The quantity <math>\frac{dQ_{k}}{T}</math> represents the ratio of a very small exchange of heat energy to the temperature Template:Mvar. The total molar entropy is the sum of many small changes in molar entropy, where each small change can be considered a reversible process.

Chemistry

The standard molar entropy of a gas at STP includes contributions from:<ref>Template:Cite book</ref>

• The heat capacity of one mole of the solid from 0Template:NbspK to the melting point (including heat absorbed in any changes between different crystal structures).
• The latent heat of fusion of the solid.
• The heat capacity of the liquid from the melting point to the boiling point.
• The latent heat of vaporization of the liquid.
• The heat capacity of the gas from the boiling point to room temperature.

Changes in entropy are associated with phase transitions and chemical reactions. Chemical equations make use of the standard molar entropy of reactants and products to find the standard entropy of reaction:<ref>Template:Cite book</ref>

<math>{\Delta S^\circ}_{rxn} = S^\circ_{products} - S^\circ_{reactants}</math>

The standard entropy of reaction helps determine whether the reaction will take place spontaneously. According to the second law of thermodynamics, a spontaneous reaction always results in an increase in total entropy of the system and its surroundings:

<math>(\Delta S_{total} = \Delta S_{system} + \Delta S_{surroundings})>0</math>

Molar entropy is not the same for all gases. Under identical conditions, it is greater for a heavier gas.

See also

• Entropy
• Heat
• Gibbs free energy
• Helmholtz free energy
• Standard state
• Third law of thermodynamics

External links

• Table of Standard Thermodynamic Properties for Selected Substances