Wankel engine

File:Wankel Cycle anim en.gif

Figure 1.
The Wankel KKM cycle: Template:Bulleted list

The Wankel engine ({{#invoke:IPA|main}}, Template:Respell) is a type of internal combustion engine using an eccentric rotary design to convert pressure into rotating motion. The concept was proven by German engineer Felix Wankel, followed by a commercially feasible engine designed by German engineer Hanns-Dieter Paschke.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The Wankel engine's rotor, which creates the turning motion, is similar in shape to a Reuleaux triangle, with the sides having less curvature. The rotor spins inside a figure-eight-like epitrochoidal housing around a fixed-toothed gearing. The midpoint of the rotor moves in a circle around the output shaft, rotating the shaft via a cam.

In its basic gasoline fuelled form, the Wankel engine has lower thermal efficiency and higher exhaust emissions relative to the four-stroke reciprocating piston engine. The thermal inefficiency has restricted the engine to limited use since its introduction in the 1960s. However, many disadvantages have mainly been overcome over the succeeding decades as the production of road-going vehicles progressed. The advantages of compact design, smoothness, lower weight, and fewer parts over the reciprocating piston internal combustion engines make the Wankel engine suited for applications such as chainsaws, auxiliary power units (APUs), loitering munitions, aircraft, jet skis, snowmobiles, and range extenders in cars. The Wankel engine was also used to power motorcycles and racing cars.

Concept

Template:Multiple image The Wankel engine is a type of rotary piston engine and exists in two primary forms, the Drehkolbenmotor (DKM, "rotary piston engine"), designed by Felix Wankel (see Figure 2.) and the Kreiskolbenmotor (KKM, "circuitous piston engine"), designed by Hanns-Dieter Paschke<ref name="Norbye 1971 p. 357">Template:Cite book</ref> (see Figure 3.), of which only the latter has left the prototype stage. Thus, all production Wankel engines are of the KKM type.

• In a DKM engine, there are two rotors: the inner, trochoid-shaped rotor, and the outer rotor, which has an outer circular shape, and an inner figure eight shape. The center shaft is stationary, and torque is taken off the outer rotor, which is geared to the inner rotor.<ref name="Hege 2015 p. 56">Template:Cite book</ref>
• In a KKM engine, the outer rotor is part of the stationary housing (thus not a moving part). The inner shaft is a moving part with an eccentric lobe for the inner rotor to spin around. The rotor spins around its center and around the axis of the eccentric shaft in a hula hoop fashion, resulting in the rotor making one complete revolution for every three revolutions of the eccentric shaft. In the KKM engine, torque is taken off the eccentric shaft,<ref name="Hege 2015 p. 53">Template:Cite book</ref> making it a much simpler design to be adopted to conventional powertrains.<ref name="Hege 2015 p. 54">Template:Cite book</ref>

Wankel engine development

Felix Wankel designed a rotary compressor in the 1920s, and received his first patent for a rotary type of engine in 1934.<ref name="Hege 2015 p. 31">Template:Cite book</ref> He realized that the triangular rotor of the rotary compressor could have intake and exhaust ports added producing an internal combustion engine. Eventually, in 1951, Wankel began working at German firm NSU Motorenwerke to design a rotary compressor as a supercharger for NSU's motorcycle engines. Wankel conceived the design of a triangular rotor in the compressor.<ref name="Hege 2015 p. 43">Template:Cite book</ref> With the assistance of Prof. Template:Ill from Stuttgart University of Applied Sciences, the concept was defined mathematically.<ref name="Hege 2015 p. 44">Template:Cite book</ref> The supercharger he designed was used for one of NSU's 50 cm³ one-cylinder two-stroke engines. The engine produced a power output of Template:Cvt at 12,000Template:Nbsprpm.<ref name="Dieter Korp 1975 p. 62-63">Template:Cite book</ref>

In 1954, NSU agreed to develop a rotary internal combustion engine with Felix Wankel, based upon Wankel's supercharger design for their motorcycle engines. Since Wankel was known as a "difficult colleague", the development work for the DKM was carried out at Wankel's private Lindau design bureau. According to John B. Hege, Wankel received help from his friend Ernst Höppner, who was a "brilliant engineer".<ref name="Hege 2015 p. 48">Template:Cite book</ref> The first working prototype, DKM 54 (see figure 2.), first ran on 1 February 1957, at the NSU research and development department Versuchsabteilung TX. It produced Template:Convert.<ref name="JhYt4Sa">Template:Cite magazine</ref><ref name="NdA81">Template:Cite news</ref> Soon after that, a second prototype of the DKM was built. It had a working chamber volume V_k of 125 cm³ and also produced Template:Cvt at 17,000Template:Nbsprpm.<ref name="Bensinger 1973 p. 56">Template:Cite book</ref> It could even reach speeds of up to 25,000Template:Nbsprpm. However, these engine speeds distorted the outer rotor's shape, thus proving impractical.<ref name="Hege 2015 p. 52">Template:Cite book</ref> According to Mazda Motors engineers and historians, four units of the DKM engine were built; the design is described to have a displacement V_h of 250 cm³ (equivalent to a working chamber volume V_k of 125 cm³). The fourth unit built is said to have received several design changes, and eventually produced Template:Cvt at 17,000 rpm; it could reach speeds up to 22,000 rpm. One of the four engines built has been on static display at the Deutsches Museum Bonn (see figure. 2).<ref name="Basshuysen Schäfer Springer Fachmedien Wiesbaden 2017 p. 484">Template:Cite book</ref>

Due to its complicated design with a stationary center shaft, the DKM engine was impractical.<ref name="Hege 2015 p. 53"/> Wolf-Dieter Bensinger explicitly mentions that proper engine cooling cannot be achieved in a DKM engine, and argues that this is the reason why the DKM design had to be abandoned.<ref name="Bensinger 1973 p. 54">Template:Cite book</ref> NSU development chief engineer Walter Froede solved this problem by using Hanns-Dieter Paschke's design and converting the DKM into what would later be known as the KKM (see figure 5.).<ref name="Hege 2015 p. 53"/> The KKM proved to be a much more practical engine, as it has easily accessible spark plugs, a simpler cooling design, and a conventional power take-off shaft.<ref name="Hege 2015 p. 54"/> Wankel disliked Froede's KKM engine because of its inner rotor's eccentric motion, which was not a pure circular motion, as Wankel had intended. He remarked that his "race horse" was turned into a "plough horse". Wankel also complained that more stresses would be placed on the KKM's apex seals due to the eccentric hula-hoop motion of the rotor. NSU could not afford to finance developing both the DKM and the KKM, and eventually decided to drop the DKM in favor of the KKM, because the latter seemed to be the more practical design.<ref name="Hege 2015 p. 57">Template:Cite book</ref>

Wankel obtained the US patent 2,988,065 on the KKM engine on 13 June 1961.<ref>Template:Cite book</ref> Throughout the design phase of the KKM, Froede's engineering team had to solve problems such as repeated bearing seizures, the oil flow inside the engine, and the engine cooling.<ref>Template:Cite book</ref> The first fully functioning KKM engine, the KKM 125, weighing in at only Template:Cvt displaced 125 cm³ and produced Template:Cvt at 11,000Template:Nbsprpm.<ref>Template:Cite book</ref> Its first run was on 1 July 1958.<ref name="Faith 1975 p. 45">Template:Cite book</ref>

In 1963, NSU produced the first series-production Wankel engine for a car, the KKM 502 (see Figure 6.). It was used in the NSU Spider sports car, of which about 2,000 were made. Despite its "teething troubles", the KKM 502 was a powerful engine with decent potential, smooth operation, and low noise emissions at high engine speeds. It was a single-rotor PP engine with a displacement of Template:Cvt, a rated power of Template:Cvt at 6,000Template:Nbsprpm and a BMEP of Template:Cvt.<ref name="Bensinger 1973 p. 127-131">Template:Cite book</ref>

Operation and design

File:Wankel engine diagram.svg

Figure 7.
Schematic of the Wankel: Template:Ordered list

File:Wankel Cycle (vector).svg

Figure 8.
The Rotary Cycle:Template:Ordered list

Figure 9. Video of a two rotor Wankel engine

File:Comparison between Wankel and reciprocating engines.svg

Figure 10.
Comparison between Wankel and reciprocating engines.<ref name="Yamamoto 1971 p. 109">Template:Cite book</ref>  Intake  Compression  Expansion  Exhaust 

File:Comparison between idealized Wankel and reciprocating engines.svg

Figure 11.
Each engine produces an average total power of 76.3 kW at p_mi = 11.1 bar and p_me = 8.88 bar. Chambers pressure, instantaneous unitary torque, instantaneous and average total torque plotted against shaft rotation angle. Instantaneous and average total power plotted against time.<ref name="Yamamoto 1971 p. 86">Template:Cite book</ref>

The Wankel engine has a spinning eccentric power take-off shaft, with a rotary piston riding on eccentrics on the shaft in a hula-hoop fashion, with the crown gear with one and a half times the number of teeth as on the eccentric shaft. Thus the Wankel is a 2:3 type of rotary engine, i.e., its housing's inner side resembles a two lobes oval-like epitrochoid (equivalent to a peritrochoid),.<ref name="Nash 1977">Template:Citation</ref> In contrast, its rotary piston has a three vertices trochoid shape (similar to a Reuleaux triangle). Thus, the Wankel engine's rotor constantly forms three moving working chambers.<ref name="Bensinger 1973 p. 55">Template:Cite book</ref> The Wankel engine's basic geometry is depicted in figure 7. Seals at the rotor's apices seal against the housing's periphery.<ref name="Columbia"/> The rotor moves in its rotating motion guided by gears and the eccentric output shaft, not being guided by the external chamber. The rotor does not make contact with the external engine housing. The force of expanded gas pressure on the rotor exerts pressure on the center of the eccentric part of the output shaft.

All practical Wankel engines are four-cycle (i.e., four-stroke) engines. In theory, two-cycle engines are possible, but they are impractical because the intake gas and the exhaust gas cannot be properly separated.<ref name="Bensinger 1973 p. 54"/> The operating principle is similar to the Otto operating principle; the Diesel operating principle with its compression ignition cannot be used in a practical Wankel engine.<ref name="Bensinger 1973 p. 86">Template:Cite book</ref> Therefore, Wankel engines typically have a high-voltage spark ignition system.<ref name="Bensinger 1973 p. 124">Template:Cite book</ref>

In a Wankel engine, one side of the triangular rotor completes the four-stage Otto cycle of intake, compression, expansion, and exhaust each revolution of the rotor (equivalent to three shaft revolutions, see Figure 8.).<ref name="oGY5n">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The shape of the rotor between the fixed apexes is to minimize the volume of the geometric combustion chamber and maximize the compression ratio, respectively.<ref name="Columbia">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="61ckr">For a detailed calculation of the curvature of a circular arc approximating the optimal Wankel rotor shape, see Template:Cite journal</ref> As the rotor has three sides, this gives three power pulses per revolution of the rotor.

Wankel engines have a much lower degree of irregularity relative to a reciprocating piston engine, making the Wankel engine run much smoother. This is because the Wankel engine has a lower moment of inertia and less excess torque area due to its more uniform torque delivery. For example, a two-rotor Wankel engine runs more than twice as smoothly as a four-cylinder piston engine.<ref name="Bensinger 1973 p. 72">Template:Cite book</ref> The eccentric output shaft of a Wankel engine also does not have the stress-related contours of a reciprocating piston engine's crankshaft. The maximum revolutions of a Wankel engine are thus mainly limited by tooth load on the synchronizing gears.<ref name="YLcmp">Kenichi Yamamoto: Rotary Engine, 1981, 3. 3. 2, Fig. 3.17 page -25-</ref> Hardened steel gears are used for extended operation above 7,000 or 8,000Template:Nbsprpm. In practice, automotive Wankel engines are not operated at much higher output shaft speeds than reciprocating piston engines of similar output power. Wankel engines in auto racing are operated at speeds up to 10,000Template:Nbsprpm, but so are four-stroke reciprocating piston engines with relatively small displacement per cylinder. In aircraft, they are used conservatively, up to 6500 or 7500Template:Nbsprpm.

Chamber volume

In a Wankel rotary engine, the chamber volume <math>V_k</math> is equivalent to the product of the rotor surface <math>A_k</math> and the rotor path <math>s</math>. The rotor surface <math>A_k</math> is given by the rotor tips' path across the rotor housing and determined by the generating radius <math>R</math>, the rotor width <math>B</math>, and the parallel transfers of the rotor and the inner housing <math>a</math>. Since the rotor has a trochoid ("triangular") shape, the sine of 60 degrees describes the interval at which the rotors get closest to the rotor housing. Therefore,

<math>A_k=2 \cdot B \cdot (R+a) \cdot \sin (60^\circ) = \sqrt 3 \cdot B \cdot (R+a)</math><ref name="Bensinger 1973 p. 64">Template:Cite book</ref>

The rotor path <math>s</math> may be integrated via the eccentricity <math>e</math> as follows:

<math>\sum \, ds= \int_{\alpha= 0^{\circ}}^{\alpha=270^{\circ}} e \cdot \sin \frac {2} 3 \alpha \, d \alpha = 3e</math>

Therefore,

<math>V_k= A_k \cdot s = \sqrt 3 \cdot B \cdot (R+a) \cdot 3e</math><ref name="Bensinger 1973 p. 65"/>

For convenience, <math>a</math> may be omitted because it is difficult to determine and small:<ref name="Yamamoto 1981 p. 15"/>

<math>V_k= \sqrt 3 \cdot B \cdot R \cdot 3e</math><ref name="Yamamoto 1981 p. 15"/><ref name="Corbat Pawlowski 1973 p. 8">Template:Cite book</ref><ref name="Bender Göhlich Springer-Verlag GmbH 2019 p. 126">Template:Cite book</ref><ref name="Ansdale Keller 1971 p. 79">Template:Cite book</ref><ref name="v Manteuffel 1971 pp. 74">Template:Cite book</ref>

A different approach to this is introducing <math>a'</math> as the farthest, and <math>a</math> as the shortest parallel transfer of the rotor and the inner housing and assuming that <math>R_1=R+a</math> and <math>R_2=R+a'</math>. Then,

<math>V_k= \sqrt 3 \cdot B \cdot (2 \cdot R_1+R_2) \cdot e</math>

Including the parallel transfers of the rotor and the inner housing provides sufficient accuracy for determining chamber volume.<ref name="Yamamoto 1981 p. 15">Template:Cite book</ref><ref name="Bensinger 1973 p. 65"/>

Equivalent displacement and power output

Different approaches have been used over time to evaluate the total displacement of a Wankel engine in relation to a reciprocating engine: considering only one, two, or all three chambers.<ref name="SAE J1220">Template:Citation</ref> Part of this dispute was because of Europe vehicle taxation being dependent on engine displacement, as reported by Karl Ludvigsen.<ref name="Ludvigsen 2003">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

If <math>y</math> is the number of chambers considered for each rotor and <math>i</math> the number of rotors, then the total displacement is:

<math>V_h=y \cdot V_k \cdot i.</math>

If <math>p_{me}</math> is the mean effective pressure, <math>N</math> the shaft rotational speed and <math>n_c</math> the number of shaft revolutions needed to complete a cycle (<math>N/n_c</math> is the frequency of the thermodynamic cycle), then the total power output is:

<math>P = p_{me} \cdot V_h \cdot {N \over n_c} = p_{me} \cdot y \cdot V_k \cdot i \cdot {N \over n_c}.</math>

Considering one chamber

Kenichi Yamamoto and Walter G. Froede placed <math>y = 1</math> and <math>n_c = 1</math>:<ref name="Yamamoto 1981 p. 37">Template:Cite book</ref><ref name="Froede 1961">Template:Cite journal</ref>

<math>P = p_{me} \cdot 1 \cdot V_k \cdot i \cdot {N \over 1}.</math>

With these values, a single-rotor Wankel engine produces the same average power as a <math>V_h</math> single-cylinder two-stroke engine, with the same average torque, with the shaft running at the same speed, operating the Otto cycles at twice the frequency.

Considering two chambers

Richard Franz Ansdale, Wolf-Dieter Bensinger and Felix Wankel based their analogy on the number of cumulative expansion strokes per shaft revolution. In a Wankel rotary engine, the eccentric shaft must make three full rotations (1080°) per combustion chamber to complete all four phases of a four-stroke engine. Since a Wankel rotary engine has three combustion chambers, all four phases of a four-stroke engine are completed within one full rotation of the eccentric shaft (360°), and one power pulse is produced at each revolution of the shaft.<ref name="Bensinger 1973 p. 65">Template:Cite book</ref><ref name="Okimoto 2002 pp. 810">Template:Cite journal
   Template:Cite journal</ref> This is different from a four-stroke piston engine, which needs to make two full rotations per combustion chamber to complete all four phases of a four-stroke engine. Thus, in a Wankel rotary engine, according to Bensinger, displacement (<math>V_h</math>) is:<ref name="Bensinger 1973 p. 66">Template:Cite book</ref><ref name="Ansdale Keller 1971 p. 82–83">Template:Cite book</ref><ref name="Wankel 1964">Template:Cite journal</ref>

<math>V_h = 2 V_k \cdot i</math>

If power is to be derived from BMEP, the four-stroke engine formula applies:

<math>P = {p_\text{me} \cdot V_\text{h} \cdot {N \over 2}}</math>

Considering three chambers

Eugen Wilhelm Huber, and Karl-Heinz Küttner counted all the chambers, since each one operates its own thermodynamic cycle. So <math>y = 3</math> and <math>n_c = 3</math>:<ref name="Wankel 1958 p. 16">Template:Cite patent, p. 16</ref><ref name="Huber 1960">Template:Cite journal</ref><ref name="Küttner 1993 p. 391">Template:Cite book</ref>

<math>P = p_{me} \cdot 3 \cdot V_k \cdot i \cdot {N \over 3}.</math>

With these values, a single-rotor Wankel engine produces the same average power as a <math>V_h</math> three-cylinder four-stroke engine, with 3/2 of the average torque, with the shaft running at 2/3 the speed, operating the Otto cycles at the same frequency:

<math>P = p_{me} \cdot 3 \cdot V_k \cdot {{2 \over 3} N \over 2}.</math>

Applying a 2/3 gear set to the output shaft of the three-cylinder (or a 3/2 one to the Wankel), the two are analogous from the thermodynamic and mechanical output point of view, as pointed out by Huber.<ref name="Huber 1960"/>

Examples (counting two chambers)

KKM 612 (NSU Ro80)

• e=14 mm
• R=100 mm
• a=2 mm
• B=67 mm
• i=2

<math>V_k = \sqrt 3 \cdot 67 \, mm \cdot (100 + 2 \, mm) \cdot 3 \cdot \, 14 \, mm \approx 498,000 \, mm^3 = 498 \, cm^3</math>

<math>V_h = 2 \cdot 498 \, cm^3 \cdot 2 = 1,992 \ cm^3</math><ref name="Bensinger 1973 p. 133">Template:Cite book</ref><ref name="Dobler 2000 pp. 440–442"/>

Mazda 13B-REW (Mazda RX-7)

• e=15 mm
• R=103 mm
• a=2 mm
• B=80 mm
• i=2

<math>V_k = \sqrt 3 \cdot 80 \, mm \cdot (103+2 \, mm) \cdot 3 \cdot \, 15 \, mm \approx 654,000 \, mm^3 = 654 \, cm^3</math>

<math>V_h = 2 \cdot 654 \, cm^3 \cdot 2 = 2,616 \ cm^3</math><ref name="Dobler 2000 pp. 440–442">Template:Cite journal</ref>

Licenses issued

NSU licensed the Wankel engine design to companies worldwide, in various forms, with many companies implementing continual improvements. In his 1973 book Rotationskolben-Verbrennungsmotoren, German engineer Wolf-Dieter Bensinger describes the following licensees, in chronological order, which is confirmed by John B. Hege:<ref name="Bensinger 1973 p. 58">Template:Cite book</ref><ref name="Hege 2006 p. 118">Template:Cite book</ref> <ref>Dieter Korp Protokoll einer Erfindung: Der Wankelmotor Lizenznehmer Page 220-221</ref>

• Curtiss-Wright: All types of engines, both air- and water-cooled, Template:Cvt, from 1958;<ref name="C9Nvu">Template:Cite magazine</ref> license sold to Deere & Company in 1984<ref name="Hege 2006 p. 208">Template:Cite book</ref>
• Fichtel & Sachs: Industrial and marine engines, Template:Cvt, from 1960
• Yanmar Diesel: Marine engines up to Template:Cvt, and engines running on diesel fuel up to Template:Cvt, from 1961
• Toyo Kogyo (Mazda): Motor vehicle engines up to Template:Cvt, from 1961
• Perkins Engines: All types of engines, up to Template:Cvt, from 1961 until <1972
• Klöckner-Humboldt-Deutz: Engines running on diesel fuel; development ended by 1972
• Daimler Benz: All types of engines from Template:Cvt up to Template:Cvt, from 1961 until 1976.
• MAN: Engines running on diesel fuel; development ended by 1972
• Krupp: Engines running on diesel fuel; development ended by 1972
• Rheinstahl-Hanomag: Petrol engines, Template:Cvt, from 1963; by 1972 merged into Daimler-Benz
• Alfa Romeo: Motor vehicle engines, Template:Cvt, from 1964
• Rolls-Royce: Engines for diesel fuel or multifuel operation, Template:Cvt, from 1965
• VEB Automobilbau: Automotive engines from Template:Cvt and Template:Cvt, from 1965; license abandoned by 1972
• Porsche: Sportscar engines from Template:Cvt, from 1965
• Outboard Marine: Marine engines from Template:Cvt, from 1966
• Comotor (NSU Motorenwerke and Citroën): Petrol engines from Template:Cvt, from 1967
• Graupner: Model engines from Template:Cvt, from 1967
• Savkel: Industrial petrol engines from Template:Cvt, from 1969
• Nissan: Car engines from Template:Cvt, from 1970
• General Motors: All types of engines, excluding aircraft engines, up to four-rotor engines, from 1970
• Suzuki: Motorcycle engines from Template:Cvt, from 1970
• Toyota: Car engines from Template:Cvt, from 1971
• Ford Germany: (including Ford Motor Company): Car engines from Template:Cvt, from 1971
• BSA Company : Petrol engines from Template:Cvt, from 1972<ref>BSA's David Garside used a F&F single-rotor engine to develop twin-rotor Wankel motorcycles that reached production: first the air-cooled Norton Classic, followed by the liquid-cooled Norton Commander & Norton F1. MidWest, an engineering firm at Staverton Airport, went on to develop the BSA/Norton engine into the MidWest AE series light aviation engines.</ref>
• Yamaha Motor Company: Petrol engines from Template:Cvt, from 1972
• Kawasaki Heavy Industries: Petrol engines from Template:Cvt, from 1972
• Brunswick Corporation Engines from Template:Cvt, from 1972
• Ingersoll Rand: Engines from Template:Cvt, from 1972
• American Motors Company: Petrol engines from Template:Cvt, from 1973

In 1961, the Soviet research organizations of NATI, NAMI, and VNIImotoprom began developing a Wankel engine. Eventually, in 1974, development was transferred to a special design bureau at the AvtoVAZ plant.<ref name="cu0Uy">Template:Cite journal</ref> John B. Hege argues that no license was issued to any Soviet car manufacturer.<ref name="Hege 2006 p. 117">Template:Cite book</ref>

Engineering

Felix Wankel managed to overcome most of the problems that made prior attempts to perfect the rotary engines fail, by developing a configuration with vane seals having a tip radius equal to the amount of "oversize" of the rotor housing form, relative to the theoretical epitrochoid, to minimize radial apex seal motion plus introducing a cylindrical gas-loaded apex pin which abutted all sealing elements to seal around the three planes at each rotor apex.<ref name="fAvRr">Template:Citation</ref>

In the early days, unique, dedicated production machines had to be built for different housing dimensional arrangements. However, patented designs such as {{#if:3824746 |[{{#ifeq:|uspto|http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=%7Chttps://patents.google.com/patent/US}}{{#iferror:{{#expr:3824746 }}|3824746}} U.S. patent {{#ifeq:Template:Replace|Template:Digits|Template:Replace|3824746}}] |{{US patent|123456|link text}}}}, G. J. Watt, 1974, for a "Wankel Engine Cylinder Generating Machine", {{#if:3916738 |[{{#ifeq:|uspto|http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=%7Chttps://patents.google.com/patent/US}}{{#iferror:{{#expr:3916738 }}|3916738}} U.S. patent {{#ifeq:Template:Replace|Template:Digits|Template:Replace|3916738}}] |{{US patent|123456|link text}}}}, "Apparatus for machining and/or treatment of trochoidal surfaces" and {{#if:3964367 |[{{#ifeq:|uspto|http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=%7Chttps://patents.google.com/patent/US}}{{#iferror:{{#expr:3964367 }}|3964367}} U.S. patent {{#ifeq:Template:Replace|Template:Digits|Template:Replace|3964367}}] |{{US patent|123456|link text}}}}, "Device for machining trochoidal inner walls", and others, solved the problem.

Wankel engines have a problem not found in reciprocating piston four-stroke engines in that the block housing has intake, compression, combustion, and exhaust occurring at fixed locations around the housing. This causes a very uneven thermal load on the rotor housing.<ref name="Bensinger 1973 p. 110">Template:Cite book</ref> In contrast, four-stroke reciprocating engines perform these four strokes in one chamber, so that extremes of "freezing" intake and "flaming" exhaust are averaged and shielded by a boundary layer from overheating working parts. The University of Florida proposed the use of heat pipes in an air-cooled Wankel to overcome this uneven heating of the block housing.<ref name="SAE paper 2014-01-2160">SAE paper 2014-01-2160</ref> Pre-heating of certain housing sections with exhaust gas improved performance and fuel economy, also reducing wear and emissions.<ref name="fpsQZ">Template:Citation</ref>

The boundary layer shields and the oil film act as thermal insulation, leading to a low temperature of the lubricating film (approximate maximum Template:Convert on a water-cooled Wankel engine). This gives a more constant surface temperature. The temperature around the spark plug is about the same as in the combustion chamber of a reciprocating engine. With circumferential or axial flow cooling, the temperature difference remains tolerable.<ref name="8AMI9">Template:Citation</ref><ref name="rTZvi">Template:Citation</ref><ref name="3mp3k">Template:Citation</ref>

Problems arose during research in the 1950s and 1960s. For a while, engineers were faced with what they called "chatter marks" and "devil's scratch" in the inner epitrochoid surface, resulting in chipping of the chrome coating of the trochoidal surfaces. They discovered that the cause was the apex seals reaching a resonating vibration, and the problem was solved by reducing the thickness and weight of the apex seals as well as using more suitable materials. Scratches disappeared after introducing more compatible materials for seals and housing coatings. Yamamoto experimentally lightened apex seals with holes. Now, weight was identified as the main cause. Mazda then used aluminum-impregnated carbon apex seals in their early production engines. NSU used carbon antimony-impregnated apex seals against chrome. NSU developed ELNISIL coating to production maturity and returned to a metal sealing strip for the RO80. Mazda continued to use chrome, but provided the aluminum housing with a steel jacket, which was then coated with a thin dimensional galvanized chrome layer. This allowed Mazda to return to the 3mm and later even 2mm thick metal apex seals.<ref>Yamamoto, Kenichi (1971). Rotary Engine. Toyo Kogyo. Page 60-61</ref> Another early problem was the build-up of cracks in the stator surface near the plug hole, which was eliminated by installing the spark plugs in a separate metal insert/ copper sleeve in the housing instead of a plug being screwed directly into the block housing.<ref name="zZeTy">Template:Citation</ref>

Toyota found that substituting a glow-plug for the leading site spark plug improved low rpm, part load, specific fuel consumption by 7%, and emissions and idle.<ref name="SAE paper 790435">SAE paper 790435</ref> A later alternative solution to spark plug boss cooling was provided with a variable coolant velocity scheme for water-cooled rotaries, which has had widespread use, being patented by Curtiss-Wright,<ref name="kM022">Template:Patent, M. Bentele, C. Jones, F. P. Sollinger, 11/7/61 and Template:Patent, C. Jones, R. E. Mount, 4/29/63 and Template:Patent, C. Jones, 7/27/65</ref> with the last-listed for better air-cooled engine spark plug boss cooling. These approaches did not require a high-conductivity copper insert, but did not preclude its use. Ford tested a Wankel engine with the plugs placed in the side plates, instead of the usual placement in the housing working surface (Template:Patent, 1978).

Torque delivery

Wankel engines are capable of high-speed operation, meaning they do not necessarily need to produce high torque to produce high power. The positioning of the intake port and intake port closing greatly affect the engine's torque production. Early closing of the intake port increases low-end torque, but reduces high-end torque (and thus power). In contrast, late closing of the intake port reduces low-end torque while increasing torque at high engine speeds, thus resulting in more power at higher engine speeds.<ref name="Bensinger 1973 p. 75">Template:Cite book</ref>

A peripheral intake port gives the highest mean effective pressure; however, side intake porting produces a more steady idle,<ref name="J6imC">Yamamoto, Kenichi. Rotary engine, fig 4.26 & 4.27, Mazda, 1981, p. 46.</ref> because it helps to prevent blow-back of burned gases into the intake ducts, which cause "misfirings" caused by alternating cycles where the mixture ignites and fails to ignite. Peripheral porting (PP) gives the best mean effective pressure throughout the rpm range, but PP was also linked to worse idle stability and part-load performance. Early work by Toyota<ref name="SAE790435">Template:Citation</ref> led to the addition of a fresh air supply to the exhaust port. It also proved that a Reed-valve in the intake port or ducts<ref name="pKO20">SAE paper 720466, Ford 1979 patent Template:Patent</ref> improved the low rpm and partial load performance of Wankel engines, by preventing blow-back of exhaust gas into the intake port and ducts, and reducing the misfire-inducing high EGR, at the cost of a slight loss of power at top rpm. Elasticity is improved with a greater rotor eccentricity, analogous to a longer stroke in a reciprocating engine.

Wankel engines operate better with a low-pressure exhaust system. Higher exhaust back pressure reduces mean effective pressure, more severely in peripheral intake port engines. The Mazda RX-8 Renesis engine improved performance by doubling the exhaust port area relative to earlier designs, and there have been studies of the effect of intake and exhaust piping configuration on the performance of Wankel engines.<ref name="Z8UtD">Ming-June Hsieh et al. SAE papers</ref> Side intake ports (as used in Mazda's Renesis engine) were first proposed by Hanns-Dieter Paschke in the late 1950s. Paschke predicted that precisely calculated intake ports and intake manifolds could make a side port engine as powerful as a PP engine.<ref name="van Basshuysen Schäfer 2017 p. 487">Template:Cite book</ref>

Materials

As formerly described, the Wankel engine is affected by unequal thermal expansion due to the four cycles taking place in fixed places of the engine. While this puts great demands on the materials used, the simplicity of the Wankel makes it easier to use alternative materials, such as exotic alloys and ceramics. A commonplace method is, for engine housings made of aluminum, to use a spurted molybdenum layer on the engine housing for the combustion chamber area, and a spurted steel layer elsewhere. Engine housings cast from iron can be induction-brazed to make the material suited for withstanding combustion heat stress.<ref name="Bensinger 1973 p. 137–138">Template:Cite book</ref>

Among the alloys cited for Wankel housing use are A-132, Inconel 625, and 356 treated to T6 hardness. Several materials have been used for plating the housing working surface, Nikasil being one. Citroën, Daimler-Benz, Ford, A P Grazen, and others applied for patents in this field. For the apex seals, the choice of materials has evolved along with the experience gained, from carbon alloys, to steel, ferritic stainless, Ferro-TiC, and other materials.<ref name="Bensinger 1973 p. 93">Template:Cite book</ref> The combination of housing plating and the apex and side seal materials was determined experimentally, to obtain the best duration of both seals and housing cover. For the shaft, steel alloys with little deformation on load are preferred, the use of Maraging steel has been proposed for this.

Leaded petrol fuel was the predominant type available in the first years of the Wankel engine's development. Lead is a solid lubricant, and leaded petrol is designed to reduce the wearing of seals and housings. The first engines had the oil supply calculated with consideration of petrol's lubricating qualities. As leaded petrol was being phased out, Wankel engines needed an increased mix of oil in the petrol to provide lubrication to critical engine parts. An SAE paper by David Garside extensively described Norton's choices of materials and cooling fins.Template:Citation needed

Sealing

Early engine designs had a high incidence of sealing loss, both between the rotor and the housing and also between the various pieces making up the housing. Also, in earlier model Wankel engines, carbon particles could become trapped between the seal and the casing, jamming the engine and requiring a partial rebuild. It was common for very early Mazda engines to require rebuilding after Template:Convert. Further sealing problems arose from the uneven thermal distribution within the housings causing distortion and loss of sealing and compression. This thermal distortion also caused uneven wear between the apex seal and the rotor housing, evident on higher mileage engines.Template:Citation needed The problem was exacerbated when the engine was stressed before reaching operating temperature. However, Mazda Wankel engines solved these initial problems. Current engines have nearly 100 seal-related parts.<ref name="JhYt4Sa"/>

The problem of clearance for hot rotor apexes passing between the axially closer side housings in the cooler intake lobe areas was dealt with by using an axial rotor pilot radially inboard of the oils seals, plus improved inertia oil cooling of the rotor interior (C-W Template:Patent, C. Jones, 5/8/63, Template:Patent, M. Bentele, C. Jones. A.H. Raye. 7/2/62), and slightly "crowned" apex seals (different height in the center and in the extremes of seal).<ref>Kenichi Yamamoto, Rotary Engine 1981, Page 50</ref>

Fuel economy and emissions

As is described in the thermodynamic disadvantages section, the early Wankel engines had poor fuel economy. This is caused by the Wankel engine's design of combustion chamber shape and huge surface area. The Wankel engine's design is, on the other hand, much less prone to engine knocking,<ref name="Bensinger 1973 p. 86"/> which allows using low-octane fuels without reducing compression. NSU tested low octane gasoline at the suggestion of Felix Wankel.

On a trial basis 40-octane gasoline was produced by BV Aral, which was used in the Wankel DKM54 test engine with a compression ratio of 8:1; it ran without complaint. This upset the petrochemical industry in Europe, which had invested considerable sums of money in new plants for the production of higher quality gasoline.<ref>Dieter Korp, Protokoll einer Erfindung - Der Wankelmotor, Motorbuch Verlag Stuttgart 1975 Template:ISBN p. 77-78</ref><ref name="Ansdale Keller 1971 p. 161">Template:Cite book</ref><ref name="Yamamoto_1971_104">'Rotary Engine', Kenichi Yamamoto; Toyo Kogyo, 1971, p. 104</ref><ref name="K. Yamamoto, T. Muroki 1972">K. Yamamoto, T. Muroki, T. KobayakawaSAE Transactions, Vol. 81, SECTION 2: Papers 720197–720445 (1972), pp. 1296-1302 (7 pages) page 1297 test run down to 56 Oktan</ref><ref>Rotary Engine and Fuel Kenichi Yamamoto 8th World Petroleum Congress Moskow 1971, Paper Number: WPC-14403</ref>

Direct injection stratified charge engines can be operated with fuels with particularly low octane numbers. Such as diesel fuel, which only has an octane number of ~25.<ref>SAE Paper 2001-01-1844/4263 Direct injection stratified charge wankel engines</ref><ref>Direct Injection Stratified Charge Rotary Engine Zachary Steven Votaw .A., Wright State University, 2011 p. 6</ref> As a result of the poor efficiency, a Wankel engine with peripheral exhaust porting has a larger amount of unburnt hydrocarbons (HC) released into the exhaust.<ref name="Bensinger 1973 p. 87">Template:Cite book</ref><ref name="36xrO">Template:Citation</ref> The exhaust is, however, relatively low in nitrogen oxide (NOx) emissions, because the combustion is slow, and temperatures are lower than in other engines, and also because of the Wankel engine's good exhaust gas recirculation (EGR) behavior. Carbon monoxide (CO) emissions of Wankel and Otto engines are about the same.<ref name="Bensinger 1973 p. 86"/>

The Wankel engine has a significantly higher (Δt_K>100 K) exhaust gas temperature than an Otto engine, especially under low and medium load conditions. This is because of the higher combustion frequency and slower combustion. Exhaust gas temperatures can exceed 1300 K under high load at engine speeds of 6000 rpm⁻¹. To improve the exhaust gas behavior of the Wankel engine, a thermal reactor or catalyst converter may be used to reduce hydrocarbon and carbon monoxide from the exhaust.<ref name="Bensinger 1973 p. 87"/>

Mazda uses a dual ignition system with two spark plugs per chamber. This increases the power output and at the same time reduces HC emissions. At the same time, HC emissions can be lowered by reducing the pre-ignition of the T leading plug relative to the L trailing plug. This leads to internal afterburning and reduces HC emissions. On the other hand, the same ignition timing of L and T leads to a higher energy conversion. Hydrocarbons adhering to the combustion chamber wall are expelled into the exhaust at the peripheral outlet.<ref>Rotary Engine', Kenichi Yamamoto; Toyo Kogyo, 1971 lower HC emisions with dual ignition with leading and trailing spark plug, p. 104</ref><ref>Rotary Engine', Kenichi Yamamoto; Toyo Kogyo, 1971 lower HC emisions with dual ignition with leading and trailing spark plug, Fig.13.9 p. 141-</ref>

Mazda used 3 spark plugs in their R26B engine per chamber. The third spark plug ignites the mixture in the trailing side before the squish is generated, causing the mixture to burn completely and, also speeding up flame propagation, which improves fuel consumption.<ref>Mazda Motor Corp.: Ritsuharu Shimizu, Tomoo Tadokoro, Toru Nakanishi, and Junichi Funamoto Mazda 4-Rotor Rotary Engine for the Le Mans 24-Hour Endurance Race SAE Paper 920309 Page 7</ref> According to Curtiss-Wright research, the factor that controls the amount of unburnt hydrocarbons in the exhaust is the rotor surface temperature, with higher temperatures resulting in fewer hydrocarbons in the exhaust.<ref name="LyHft">Template:Citation</ref> Curtiss-Wright widened the rotor, keeping the rest of engine's architecture unchanged, thus reducing friction losses and increasing displacement and power output. The limiting factor for this widening was mechanical, especially shaft deflection at high rotative speeds.<ref name="NIGaB">SAE paper 710582</ref> Quenching is the dominant source of hydrocarbon at high speeds and leakage at low speeds.<ref name="Wum7B">Template:Citation</ref> Using side-porting which enables closing the exhaust port around the top-dead center and reducing intake and exhaust overlap helps improving fuel consumption.<ref name="36xrO"/>

Mazda's RX-8 car with the Renesis engine (that was first presented in 1999), met in 2004 the United States' low emissions vehicle (LEV-II) standard.<ref name="Dobler 2000 pp. 440–442"/> This was mainly achieved by using side porting: The exhaust ports, which in earlier Mazda rotary engines were located in the rotor housings, were moved to the side of the combustion chamber. This approach allowed Mazda to eliminate overlap between intake and exhaust port openings, while simultaneously increasing the exhaust port area. This design improved the combustion stability in the low-speed and light load range. The HC emissions from the side exhaust port rotary engine are 35–50% less than those from the peripheral exhaust port Wankel engine. Peripheral ported rotary engines have a better mean effective pressure, especially at high rpm and with a rectangular-shaped intake port.<ref name="y5HHx">Template:Citation</ref><ref>SAE Paper 950454 Page 7</ref> However, the RX-8 was not improved to meet Euro 5 emission regulations, and it was discontinued in 2012.<ref name="EjVRK">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The new Mazda 8C of the Mazda MX-30 R-EV meets the Euro 6d-ISC-FCM emissions standard.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Laser ignition

Laser ignition was first proposed in 2011,<ref name="autocar.co.uk">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> but first studies of laser ignition were only conducted in 2021. It is assumed that laser ignition of lean fuel mixtures in Wankel engines could improve fuel consumption and exhaust gas behavior. In a 2021 study, a Wankel model engine was tested with laser ignition and various gaseous and liquid fuels. Laser ignition leads to a faster center of combustion development, thus improving combustion speed, leading to a reduction in NO_x emissions. The laser pulse energy required for proper ignition is "reasonable", in the low single-digit mJ-range. A significant modification of the Wankel engine is not required for laser ignition.<ref name="Loktionov Pasechnikov 2021 p=012031">Template:Cite journal</ref>

Compression-ignition Wankel

File:Two Stage Rotary RR R1C.jpg

Figure 16.
Rolls-Royce R1C compression ignition prototype

Research has occurred into rotary compression ignition engines. The basic design parameters of the Wankel engine preclude obtaining a compression ratio sufficient for Diesel operation in a practical engine.<ref name="Eichlseder Klüting Piock 2008 p. 222">Template:Cite book</ref> The Rolls-Royce<ref name="zqxX7">Autocar magazine, week ending Dec 17, 1970</ref> and Yanmar compression-ignition<ref name="tqVfR">SAE paper 870449</ref> approach was to use a two-stage unit (see figure 16.), with one rotor acting as compressor, while combustion takes place in the other.<ref name="LfWIG">Wolf-Dieter Bensinger: Rotationskolben-Verbrennungsmotoren, Springer, Berlin/Heidelberg/New York 1973, Template:ISBN. p. 141</ref> Both engines were not functional.<ref name="Eichlseder Klüting Piock 2008 p. 222"/>

Multifuel Wankel engine

A different approach from a compression ignition (Diesel) Wankel engine is a non-CI, multifuel Wankel engine that is capable of operating on a huge variety of fuels: diesel, petrol, kerosene, methanol, natural gas, and hydrogen.<ref name="auto">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref>Wankel Journal, No. 74, January 2015, p. 23</ref> German engineer Dankwart Eiermann designed this engine at Wankel SuperTec (WST) in the early 2000s. It has a chamber volume of 500 cm³ (cc) and an indicated power output of Template:Convert per rotor. Versions with one up to four rotors are possible.<ref name="Wankel Journal p. 22">Template:Cite journal</ref>

The WST engine has a common-rail direct injection system operating on a stratified charge principle. Similar to a Diesel engine and unlike a conventional Wankel engine, the WST engine compresses air rather than an air–fuel mixture as in the four-cycle engine compression phase. Fuel is only injected into the compressed air shortly before top-dead centre, which results in stratified charge (i.e., no homogeneous mixture). A spark plug is used to initiate combustion.<ref>Wankel Journal, No. 74, January 2015, p. 24</ref> The pressure at the end of the compression phase and during combustion is lower than in a conventional Diesel engine,<ref name="Wankel Journal p. 22"/> and the fuel consumption is equivalent to that of a small indirect injection compression ignition engine (i.e., >250 g/(kW·h)).<ref>Wankel Journal, No. 74, January 2015, p. 27</ref>

Diesel-fuel-powered variants of the WST Wankel engine are being used as APUs in 60 Deutsche Bahn diesel locomotives. The WST diesel fuel engines can produce up to Template:Convert.<ref name="lr-online.de 2020">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="auto"/>

Hydrogen fuel

File:Mazda RX8 hydrogen rotary car 1.jpg

Figure 15.
Mazda RX-8 Hydrogen RE hydrogen-fuelled rotary-engined car

As a hydrogen/air fuel mixture is quicker to ignite with a faster burning rate than gasoline, an important issue of hydrogen internal combustion engines is to prevent pre-ignition and backfire. In a rotary engine, each cycle of the Otto cycle occurs in different chambers. Importantly, the intake chamber is separated from the combustion chamber, keeping the air/fuel mixture away from localized hot spots. Wankel engines also do not have hot exhaust valves, which eases adapting them to hydrogen operation.<ref>Template:Cite journal</ref> Another problem concerns the hydrogenate attack on the lubricating film in reciprocating engines. In a Wankel engine, the problem of a hydrogenate attack is circumvented by using ceramic apex seals.<ref name="WQkIw">1980 BMF report hydrogen Audi EA871 comparison to a hydrogen reciprocating piston engine page 11. Page 8 higher lubricating oil consumption caused by hydrogen</ref><ref name="V4ltk">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

In a prototype Wankel engine fitted to a Mazda RX-8 to research hydrogen operation, Wakayama et al. found that hydrogen operation improved thermal efficiency by 23% over petrol fuel operation. Although the lean operation emits little NOx, total amount of engine-out NOx exceeds Japanese SULEV standard. The supplementary stoichiometic operation combined with a catalyst provides additional NOx reduction. Accordingly, the vehicle satisfies the SULEV standard.<ref name="cder.dz">Template:Cite conference</ref>

Advantages

Prime advantages of the Wankel engine are:<ref name="PS-April-1966">Template:Cite magazine</ref>

• A far higher power-to-weight ratio than a piston engine<ref name="Ansdale Keller 1971 p. 205">Template:Cite book</ref>
• Easier to package in small engine spaces than an equivalent piston engine<ref name="Ansdale Keller 1971 p. 205"/>
• Able to reach higher engine speeds than a comparable piston engine
• Operating with almost no vibration<ref name="Ansdale Keller 1971 p. 203"/>
• Not prone to engine-knock<ref name="Bensinger 1973 p. 86"/><ref name="Yamamoto_1971_104"/><ref name="K. Yamamoto, T. Muroki 1972"/>
• Cheaper to mass-produce, because the engine contains fewer parts<ref name="Ansdale Keller 1971 p. 205"/>
• Supplying torque for about two-thirds of the combustion cycle rather than one-quarter for a piston engine<ref name="Ansdale Keller 1971 p. 203">Template:Cite book</ref>
• Easily adapted and highly suitable to use hydrogen fuel.

Wankel engines are considerably lighter and simpler, containing far fewer moving parts than piston engines of equivalent power output. Valves or complex valve trains are eliminated by using simple ports cut into the walls of the rotor housing. Since the rotor rides directly on a large bearing on the output shaft, there are no connecting rods and no crankshaft. The elimination of reciprocating mass gives Wankel engines a low non-uniformity coefficient, meaning that they operate much smoother than comparable reciprocating piston engines. For example, a two-rotor Wankel engine is more than twice as smooth in its operation as a four-cylinder reciprocating piston engine.<ref name="Bensinger 1973 p. 72"/>

A four-stroke cylinder produces a power stroke only every other rotation of the crankshaft, with three strokes being pumping losses. The Wankel engine also has higher volumetric efficiency than a reciprocating piston engine.<ref name="s4PSp">Template:Cite book</ref> Because of the quasi-overlap of the power strokes, the Wankel engine is very quick to react to power increases, delivering power quickly when demanded, especially at higher engine speeds. This difference is more pronounced relative to four-cylinder reciprocating engines and less pronounced relative to higher cylinder counts.

Due to the absence of hot exhaust valves, the fuel octane requirements of Wankel engines are lower than in reciprocating piston engines.<ref name="Bensinger 1973 p. 85"/> As a rule of thumb, it may be assumed that a Wankel engine with a working chamber volume V_k of 500 cm³ and a compression of ε=9 runs well on mediocre-quality petrol with an octane rating of just 91 RON.<ref name="Bensinger 1973 p. 86"/> If in a reciprocating piston engine, the compression must be reduced by one unit of compression to avoid knock, then, in a comparable Wankel engine, a reduction in compression may not be required.<ref name="Bensinger 1973 p. 88">Template:Cite book</ref>

Because of the lower injector count, fuel injection systems in Wankel engines are cheaper than in reciprocating piston engines. An injection system that allows stratified charge operation may help reduce rich mixture areas in undesirable parts of the engine, which improves fuel efficiency.<ref name="Bensinger 1973 p. 82–83">Template:Cite book</ref>

Disadvantages

Thermodynamic disadvantages

Wankel rotary engines mainly suffer from poor thermodynamics caused by the Wankel engine's design with its huge surface area and poor combustion chamber shape. As an effect of this, the Wankel engine has slow and incomplete combustion, which results in high fuel consumption and bad exhaust gas behavior.<ref name="Bensinger 1973 p. 85">Template:Cite book</ref> Wankel engines can reach a typical maximum efficiency of about 30 percent.<ref name="Automotive Handbook 2022 page 642">Template:Cite book</ref>

In a Wankel rotary engine, fuel combustion is slow, because the combustion chamber is long, thin, and moving. Flame travel occurs almost exclusively in the direction of rotor movement, adding to the poor quenching of the fuel and air mixture, being the main source of unburnt hydrocarbons at high engine speeds: The trailing side of the combustion chamber naturally produces a "squeeze stream" that prevents the flame from reaching the chamber's trailing edge, which worsens the consequences of the fuel and air mixture quenching poorly. Direct fuel injection, in which fuel is injected towards the leading edge of the combustion chamber, can minimize the amount of unburnt fuel in the exhaust.<ref name="telegraph.co.uk">Template:Cite newsTemplate:Cbignore</ref><ref name=Pj5Jo>Template:Cite newsTemplate:Cbignore</ref>

Mechanical disadvantages

Although many of the disadvantages are the subject of ongoing research, the current disadvantages of the Wankel engine in production are the following:<ref name="M9jv4">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Rotor sealing

The engine housing has vastly different temperatures in each separate chamber section. The different expansion coefficients of the materials lead to imperfect sealing. Additionally, both sides of the apex seals are exposed to fuel, and the design does not allow for controlling the lubrication of the rotors accurately and precisely. Rotary engines tend to be overlubricated at all engine speeds and loads, and have relatively high oil consumption and other problems resulting from excess oil in the combustion areas of the engine, such as carbon formation and excessive emissions from burning oil. By comparison, a piston engine has all functions of a cycle in the same chamber giving a more stable temperature for piston rings to act against. Additionally, only one side of the piston in a (four-stroke) piston engine is exposed to fuel, allowing oil to lubricate the cylinders from the other side. Piston engine components can also be designed to increase ring sealing and oil control as cylinder pressures and power levels increase. To overcome the problems in a Wankel engine of differences in temperatures between different regions of housing and side and intermediary plates, and the associated thermal dilatation inequities, a heat pipe has been used to transport heat from the hot to the cold parts of the engine. The "heat pipes" effectively direct hot exhaust gas to the cooler parts of the engine, resulting in decreases in efficiency and performance. In small-displacement, charge-cooled rotor, air-cooled housing Wankel engines, that has been shown to reduce the maximum engine temperature from Template:Convert, and the maximum difference between hotter and colder regions of the engine from Template:Convert.<ref name="XFvJn">Template:Citation</ref>

Apex seal lifting

Centrifugal force pushes the apex seal onto the housing surface forming a firm seal. Gaps can develop between the apex seal and trochoid housing in light-load operation when imbalances in centrifugal force and gas pressure occur. At low engine-rpm ranges, or under low-load conditions, the gas pressure in the combustion chamber can cause the seal to lift off the surface, resulting in combustion gas leaking into the next chamber. Mazda developed a solution, changing the shape of the trochoid housing, which meant that the seals remained flush with the housing. Using the Wankel engine at sustained higher revolutions helps eliminate apex seal lift-off, making it viable in applications such as electricity generation. In motor vehicles, the engine is suited to series-hybrid applications.<ref name="VPlGg">{{#invoke:citation/CS1|citation

|CitationClass=web }}</ref> NSU circumvented this problem by adding slots on one side of the apex seals, thus directing the gas pressure into the base of the apex. This effectively prevented the apex seals from lifting off.<ref>Norbye, Jan P., The Wankel engine Design Development Applications, p.134</ref>

Although in two dimensions the seal system of a Wankel looks to be even simpler than that of a corresponding multi-cylinder piston engine, in three dimensions the opposite is true. As well as the rotor apex seals evident in the conceptual diagram, the rotor must also seal against the chamber ends.

Piston rings in reciprocating engines are not perfect seals; each has a gap to allow for expansion. The sealing at the apexes of the Wankel rotor is less critical because leakage is between adjacent chambers on adjacent strokes of the cycle, rather than to the mainshaft case. Although sealing has improved over the years, the less-than-effective sealing of the Wankel, which is mostly due to lack of lubrication, remains a factor reducing its efficiency.<ref name="Eberle Klomp 1973 p. 454">Template:Cite conference</ref>

The trailing side of the rotary engine's combustion chamber develops a squeeze stream that pushes back the flame front. With the conventional one or two-spark-plug system and homogenous mixture, this squeeze stream prevents the flame from propagating to the combustion chamber's trailing side in the mid and high-engine speed ranges.<ref name="SAE720357">Template:Citation</ref> Kawasaki dealt with that problem in its US patent Template:Patent; Toyota obtained a 7% economy improvement by placing a glow-plug in the leading side, and using Reed-Valves in intake ducts. In two-stroke engines, metal reeds last about Template:Convert while carbon fiber, around Template:Convert.<ref name="SAE790435"/> This poor combustion in the trailing side of the chamber is one of the reasons why there is more carbon monoxide and unburned hydrocarbons in a Wankel's exhaust stream. A side-port exhaust, as is used in the Mazda Renesis, avoids port overlap, one of the causes of this, because the unburned mixture cannot escape. The Mazda 26B avoided this problem through the use of a three spark-plug ignition system and obtained a complete conversion of the aspirated mixture. In the 26B, the upper late trailing spark plug ignites before the onset of the squeeze flow.<ref name="SAE 930677">Template:Citation</ref>

Regulations and taxation

National agencies that tax automobiles according to displacement and regulatory bodies in automobile racing use a variety of equivalency factors to compare Wankel engines to four-stroke piston engines. Greece, for example, taxed cars based on the working chamber volume (the face of one rotor), multiplied by the number of rotors, lowering the cost of ownership.Template:Citation needed Japan did the same, but applied an equivalency factor of 1.5, making Mazda's 13B engine fit just under the 2-liter tax limit. FIA used an equivalency factor of 1.8 but later increased it to 2.0, using the displacement formula described by Bensinger. However, the DMSB applies an equivalency factor of 1.5 in motorsport.<ref>TECHNISCHE DMSB-BESTIMMUNGEN 2023 [1], 1 January 2023</ref>

Car applications

Template:Multiple image The first rotary-engined car for sale was the 1964 NSU Rotary Spider. Rotary engines were continuously fitted in cars until 2012 when Mazda discontinued the RX-8. Mazda introduced a rotary-engined hybrid electric car, the MX-30 R-EV in 2023.<ref name="capomazda.com">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

NSU and Mazda

Mazda and NSU signed a study contract to develop the Wankel engine in 1961 and competed to bring the first Wankel-powered automobile to the market. Although Mazda produced an experimental rotary that year, NSU was the first with a rotary automobile for sale, the sporty NSU Spider in 1964; Mazda countered with a display of two- and four-rotor rotary engines at that year's Tokyo Motor Show.<ref name="JhYt4Sa"/> In 1967, NSU began production of a rotary-engined luxury car, the Ro 80.<ref name="ndjUi">Template:Cite magazine</ref> NSU had not produced reliable apex seals on the rotor, though, unlike Mazda and Curtiss-Wright. NSU had problems with apex seals' wear, poor shaft lubrication, and poor fuel economy, leading to frequent engine failures, not solved until 1972, which led to large warranty costs curtailing further NSU rotary engine development. This premature release of the new rotary engine gave a poor reputation for all makes, and even when these issues were solved in the last engines produced by NSU in the second half of the '70s, sales did not recover.<ref name="JhYt4Sa"/>

By early 1978, Audi engineers Richard van Basshuysen and Gottlieb Wilmers had designed a new generation of the Audi NSU Wankel engine, the KKM 871. It was a two-rotor unit with a chamber volume V_k of 746.6 cm³, derived from an eccentricity of 17 mm, a generating radius of 118.5 mm, and equidistance of 4 mm and a housing width of 69 mm. It had double side intake ports, and a peripheral exhaust port; it was fitted with a continuously injecting Bosch K-Jetronic multipoint manifold injection system. According to the DIN 70020 standard, it produced 121 kW at 6500 rpm, and could provide a max. torque of 210 N·m at 3500 rpm.<ref name="Van Basshuysen Wilmers 1978 p. 3"/> Van Basshuysen and Wilmers designed the engine with either a thermal reactor, or a catalytic converter for emissions control.<ref name="Van Basshuysen Wilmers 1978 p. 3">Template:Cite conference</ref> The engine had a mass of 142 kg,<ref name="Van Basshuysen Wilmers 1978 p. 3"/> and a BSFC of approximately 315 g/(kW·h) at 3000 rpm and a BMEP of 900 kPa.<ref name="Van Basshuysen Wilmers 1978 p. 11">Template:Cite conference</ref> For testing, two KKM 871 engines were installed in Audi 100 Type 43 test cars, one with a five-speed manual gearbox, and one with a three-speed automatic gearbox.<ref name="Van Basshuysen Wilmers 1978 p. 16">Template:Cite conference</ref>

Mazda

Mazda claimed to have solved the apex seal problem, operating test engines at high speed for 300 hours without failure.<ref name="JhYt4Sa"/> After years of development, Mazda's first rotary engine car was the 1967 Cosmo 110S. The company followed with several Wankel ("rotary" in the company's terminology) vehicles, including a bus and a pickup truck. Customers often cited the cars' smoothness of operation. However, Mazda chose a method to comply with hydrocarbon emission standards which, while less expensive to produce, increased fuel consumption.

Mazda later abandoned the rotary in most of their automotive designs, continuing to use the engine in their sports car range only. The company normally used two-rotor designs. A more advanced twin-turbo three-rotor engine was fitted in the 1990 Eunos Cosmo sports car. In 2003, Mazda introduced the Renesis engine fitted in the RX-8. The Renesis engine relocated the ports for exhaust from the periphery of the rotary housing to the sides, allowing for larger overall ports, and better airflow.<ref name="Qbqnp">Masaki Ohkubo et al., SAE paper 2004-01-1790</ref> The Renesis is capable of Template:Cvt with improved fuel economy, reliability, and lower emissions than prior Mazda rotary engines,<ref name="cBaLx">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> all from a nominal 2.6 L displacement, but this was not enough to meet more stringent emissions standards. Mazda ended production of their rotary engine in 2012 after the engine failed to meet the more stringent Euro 5 emission standards, leaving no automotive company selling a rotary-powered road vehicle until 2023.<ref name="CGHhL">Template:Cite news</ref>

Mazda launched the MX-30 R-EV hybrid fitted with a Wankel engine range extender in March 2023.<ref name="capomazda.com"/> The Wankel engine has no direct connection to the wheels serving only to charge the battery. It is a single-rotor unit with a Template:Cvt engine with a rated power output of Template:Cvt. The engine has petrol direct injection, exhaust gas recirculation, and an exhaust-gas treatment system with a Three-way catalyst and a particulate filter. The engine is Euro 6d-ISC-FCM-compliant.<ref name="auto motor und sport 2023">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="auto1">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Citroën

Citroën did much research, producing the M35 and GS Birotor cars, and the Template:Interlanguage link helicopter, using engines produced by Comotor, a joint venture by Citroën and NSU.

Daimler-Benz

Daimler-Benz fitted a Wankel engine in their C111 concept car. The C 111-II's engine was naturally aspirated, fitted with petrol direct injection, and had four rotors. The total displacement was Template:Convert, and the compression ration was 9.3:1 It provided a maximum torque of Template:Cvt at 5,000Template:Nbsprpm and a power output of Template:Cvt at 6,000Template:Nbsprpm.<ref name="Dobler 2000 pp. 440–442"/>

American Motors

American Motors Corporation (AMC) was so convinced "... that the rotary engine will play an important role as a powerplant for cars and trucks of the future ...", that the chairman, Roy D. Chapin Jr., signed an agreement in February 1973 after a year's negotiations, to build rotary engines for both passenger cars and military vehicles, and the right to sell any rotary engines it produced to other companies.<ref name="D1JXj">Template:Cite magazine</ref><ref name="4aVPu">Template:Cite book</ref> AMC's president, William Luneburg, did not expect dramatic development through to 1980, but Gerald C. Meyers, AMC's vice president of the engineering product group, suggested that AMC should buy the engines from Curtiss-Wright before developing its own rotary engines, and predicted a total transition to rotary power by 1984.<ref name="EylYW">Template:Cite book</ref>

Plans called for the engine to be used in the AMC Pacer, but development was pushed back.<ref name="N9680">Template:Cite magazine</ref><ref name="AyqBG">Template:Cite magazine</ref> American Motors designed the unique Pacer around the engine. By 1974, AMC had decided to purchase the General Motors (GM) rotary instead of building an engine in-house.<ref name="pkgwv">Template:Cite magazine</ref> Both GM and AMC confirmed the relationship would be beneficial in marketing the new engine, with AMC claiming that the GM rotary achieved good fuel economy.<ref name="1OYME">Template:Cite magazine</ref> GM's engines had not reached production when the Pacer was launched onto the market. The 1973 oil crisis played a part in frustrating the use of the rotary engine. Rising fuel prices and speculation about proposed US emission standards legislation also increased concerns.

General Motors

At its annual meeting in May 1973, General Motors unveiled the Wankel engine it planned to use in the Chevrolet Vega.<ref name=regupunv>Template:Cite news</ref> By 1974, GM R&D had not succeeded in producing a Wankel engine meeting both the emission requirements and good fuel economy, leading to a decision by the company to cancel the project. Because of that decision, the R&D team only partly released the results of its most recent research, which claimed to have solved the fuel-economy problem and built reliable engines with a lifespan above Template:Convert. Those findings were not taken into account when the cancellation order was issued. The ending of GM's rotary project required AMC, who was to purchase the engine, to reconfigure the Pacer to house its AMC straight-6 engine driving the rear wheels.<ref name="RTINh">Template:Cite book</ref>

AvtoVAZ

In 1974, the Soviet Union created a special engine-design bureau, which, in 1978, designed an engine designated as VAZ-311 fitted into a VAZ-2101 car.<ref name="BLpRB">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> In 1980, the company began delivering the VAZ-411 twin-rotor Wankel engine in VAZ-2106 cars, with about 200 being manufactured. Most of the production went to the security services.<ref name="1paIa">"LADA – part II" Autosoviet, undated, retrieved on September 27, 2008.</ref><ref name="7IBoX">"ЛИНИЯ ЖИЗНИ – ЭПИТРОХОИДА" 01.07.2001 Template:Webarchive, retrieved on September 27, 2008. Template:In lang</ref>

Ford

Ford conducted research in rotary engines, resulting in patents granted: Template:Patent, 1974, a method for fabricating housings; Template:Patent 1974, side plates coating; Template:Patent, 1975, housing coating; Template:Patent, 1978: Housings alignment; Template:Patent, 1979, reed-valve assembly. In 1972, Henry Ford II stated that the rotary probably would not replace the piston in "my lifetime".<ref name="Y40Pb">Template:Cite book</ref>

Car racing

File:Mazda-787B.JPG

Figure 23.
Mazda 787B

The Sigma MC74 powered by a Mazda 12A engine was the first engine and only team from outside Western Europe or the United States to finish the entire 24Template:Nbsphours of the 24 Hours of Le Mans race, in 1974. Yojiro Terada was the driver of the MC74. Mazda was the first team from outside Western Europe or the United States to win Le Mans outright. It was also the only non-piston engined car to win Le Mans, which the company accomplished in 1991 with their four-rotor 787B (Template:Convert displacement), rated by FIA formula at Template:Convert). In the C2 class, all participants had the same amount of fuel. The only exception was the unregulated C1 Category 1. This category only allowed naturally aspirated engines. The Mazdas were classified as naturally aspirated to start with 830 kg weight, 170 kg less than the supercharged competitors.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The cars under the Group C1 Category 1 regulations for 1991 were allowed to be another 80 kg lighter than the 787B.<ref>Tare weight Peugeot 905 750kg</ref> In addition, Group C1 Category 1 had only permitted 3.5-liter naturally aspirated engines and had no fuel quantity limits.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

As a vehicle range extender

File:Hybridpeak.svg

Figure 24.
Structure of a series-hybrid vehicle. The grey square represents a differential gear. An alternative arrangement (not shown) is to have electric motors at two or four wheels.

Due to the compact size and the high power-to-weight ratio of a Wankel engine, it has been proposed for electric vehicles as range extenders to provide supplementary power when electric battery levels are low. A Wankel engine used as a generator has packaging, noise, vibration, and harshness advantages when used in a passenger car, maximizing interior passenger and luggage space, as well as providing a good noise and vibration emissions profile. However, it is questionable whether or not the inherent disadvantages of the Wankel engine allow the usage of the Wankel engine as a range extender for passenger cars.<ref name="Merker Teichmann Springer Fachmedien Wiesbaden 2019 p. 484">Template:Cite book</ref>

In 2010, Audi unveiled a prototype series-hybrid electric car, the A1 e-tron. It incorporated a Wankel engine with a chamber volume V_k of 254 cm³, capable of producing 18 kW at 5000 rpm. It was mated to an electric generator, which recharged the car's batteries as needed and provided electricity directly to the electric driving motor. The package had a mass of 70 kg and could produce 15 kW of electric power.<ref name="Ribau Silva Brito Martins 2012 pp. 120–133">Template:Cite journal</ref>

File:DEMIO EV 20130126-1.JPG

Figure 25.
Mazda2 EV prototype

In November 2013, Mazda announced to the motoring press a series-hybrid prototype car, the Mazda2 EV, using a Wankel engine as a range extender. The generator engine, located under the rear luggage floor, is a tiny, almost inaudible, single-rotor 330-cc unit, generating Template:Cvt at 4,500Template:Nbsprpm and maintaining a continuous electric output of 20 kW.<ref>Template:Cite magazine</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="Xr2Bg">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Mazda introduced the MX-30 R-EV fitted with a Wankel engine range extender in March 2023.<ref name="capomazda.com"/> The car's Wankel engine is a naturally aspirated single-rotor unit with a chamber volume V_k of Template:Cvt, a compression of 11.9, and a rated power output of Template:Cvt. It has petrol direct injection, exhaust gas recirculation, and an exhaust-gas treatment system with a TWC and a particulate filter. According to auto motor und sport, the engine is Euro 6d-ISC-FCM-compliant.<ref name="auto motor und sport 2023"/><ref name="auto1"/>

Motorcycle applications

The first Wankel-engined motorcycle was an MZ-built MZ ES 250, fitted with a water-cooled KKM 175 W Wankel engine. An air-cooled version followed this in 1965, called the KKM 175 L. The engine produced Template:Cvt at 6,750Template:Nbsprpm, but the motorcycle never went into series production.<ref name="Walker 2004 p. 27-28">Template:Cite book</ref>

Norton

In Britain, Norton Motorcycles developed a Wankel rotary engine for motorcycles, based on the Sachs air-cooled rotor Wankel that powered the DKW/Hercules W-2000 motorcycle. This two-rotor engine was included in the Commander and F1. Norton improved on Sachs's air cooling, introducing a plenum chamber. Suzuki also made a production motorcycle powered by a Wankel engine, the RE-5, using ferroTiC alloy apex seals and an NSU rotor in a successful attempt to prolong the engine's life.

In the early 1980s, using earlier work at BSA, Norton produced the air-cooled twin-rotor Classic, followed by the liquid-cooled Commander and the Interpol2 (a police version).<ref name="p1htL">Template:Citation (translation).</ref> Subsequent Norton Wankel bikes included the Norton F1, F1 Sports, RC588, Norton RCW588, and NRS588. Norton proposed a new 588-cc twin-rotor model called the "NRV588" and a 700-cc version called the "NRV700".<ref name="8j5sm">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> A former mechanic at Norton, Brian Crighton, started developing his own rotary engined motorcycles line named "Roton", which won several Australian races.

Despite successes in racing,<ref name="oMPvj">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> no motorcycles powered by Wankel engines have been produced for sale to the general public for road use since 1992.

Yamaha

In 1972, Yamaha introduced the RZ201 at the Tokyo Motor Show, a prototype with a Wankel engine, weighing 220 kg and producing Template:Convert from a twin-rotor 660-cc engine (US patent N3964448). In 1972, Kawasaki presented its two-rotor Kawasaki X99 rotary engine prototype (US patents N 3848574 &3991722). Both Yamaha and Kawasaki claimed to have solved the problems of poor fuel economy, high exhaust emissions, and poor engine longevity in early Wankels, but neither prototype reached production.

Hercules

In 1974, Hercules produced W-2000 Wankel motorcycles, but low production numbers meant the project was unprofitable, and production ceased in 1977.<ref name="J2L1g">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Suzuki

From 1975 to 1976, Suzuki produced its RE5 single-rotor Wankel motorcycle. It was a complex design, with both liquid cooling and oil cooling, and multiple lubrication and carburetor systems. It worked well and was smooth, but it did not sell well because it was heavy and had a modest power output of Template:Convert.<ref name="ncNHg">Template:Citation</ref> Suzuki opted for a complicated oil-cooling and water-cooling system. The exhaust pipes become very hot, with Suzuki opting for a finned exhaust manifold, twin-skinned exhausted pipes with cooling grilles, heatproof pipe wrappings, and silencers with heat shields. Suzuki had three lube systems, while Garside had a single total-loss oil injection system that fed both the main bearings and the intake manifolds. Suzuki chose a single rotor that was fairly smooth, but with rough patches at 4,000 rpm. Suzuki mounted the massive rotor high in the frame.<ref name="D1mEV">"Cycle World" Magazine March 1971</ref> Although it was described to handle well, the result was that the Suzuki was heavy, overcomplicated, expensive to manufacture, and, at 62 bhp, short on power.

Van Veen

Dutch motorcycle importer and manufacturer Van Veen produced small quantities of a dual-rotor Wankel-engined OCR-1000 motorcycle between 1978 and 1980, using surplus Comotor engines. The OCR 1000 engine used a modified KKM 624 engine initially intended for the Citroën GS Birotor car.<ref name="sw66B">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Whereby an electronic map ignition from Hartig replaced the ignition distributor.<ref name="Der Spiegel (2)">Der Spiegel Magazin, Ausgabe Nr. 38 von 1978, S. 256 ff.</ref>

Non-road vehicle applications

Aircraft

Rotary engines are well suited for light aircraft, being light, compact, almost vibrationless, and with a high power-to-weight ratio. Further aviation benefits include:

1. The engine is not susceptible to shock-cooling during descent;
2. The engine does not require an enriched mixture for cooling at high power;
3. Having no reciprocating parts, less vulnerability to damage occurs when the engine revolves at a higher rate than the designed maximum.

Unlike cars and motorcycles, a rotary aero-engine can be sufficiently warm before full power is applied because of the time taken for pre-flight checks. Also, the journey to the runway has minimum cooling, which further permits the engine to reach the operating temperature for full power on take-off.<ref name="H8TbB">MidWest Engines Ltd AE1100R Rotary Engine Manual</ref> A Wankel aero-engine spends most of its operational time at high power outputs, with little idling.

Since rotary engines operate at a relatively high rotational speed, at 6,000Template:Nbsprpm of the output shaft, the rotor spins only at about one-third of that speed. With relatively low torque, propeller-driven aircraft must use a propeller speed reduction unit to maintain propellers within the designed speed range. Experimental aircraft with Wankel engines use propeller speed reduction units; for example, the MidWest twin-rotor engine has a 2.95:1 reduction gearbox.

The first rotary engine aircraft was in the late-1960s in the experimental Lockheed Q-Star civilian version of the United States Army's reconnaissance QT-2, essentially a powered Schweizer sailplane.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The plane was powered by a Template:Convert Curtiss-Wright RC2-60 Wankel rotary engine.<ref name="airandspace.si.edu">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The same engine model was also used in a Cessna Cardinal and a helicopter, as well as other airplanes.<ref name="PS-April-1966"/><ref name="kza2k">Template:Citation</ref><ref name="PTyY3">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The French company Citroën developed a rotary-powered Template:Interlanguage link helicopter in the 1970s.<ref name="PBoulay">Template:Cite book</ref> In Germany in the mid-1970s, a pusher ducted fan airplane powered by a modified NSU multi-rotor rotary engine was developed in both civilian and military versions, Fanliner and Fantrainer.<ref name="Popular Science p. 88">Template:Cite magazine</ref>

At roughly the same time as the first experiments with full-scale aircraft powered with rotary engines, model aircraft-sized versions were pioneered by a combination of the well-known Japanese O.S. Engines firm and the then-extant German Graupner aeromodelling products firm, under license from NSU. The Graupner model Wankel engine has a chamber volume V_k of 4.9 cm³, and produces 460 W at 16,000 rpm⁻¹; its mass is 370 g. It was produced by O.S. engines of Japan.<ref name="Bensinger 1973 p. 142">Template:Cite book</ref>

Rotary engines have been fitted in homebuilt experimental aircraft, such as the ARV Super2, a couple of which were powered by the British MidWest aero-engine. Most are Mazda 12A and 13B automobile engines, converted for aviation use. This is a very cost-effective alternative to certified aircraft engines, providing engines ranging from 100 to Template:Convert at a fraction of the cost of traditional piston engines. These conversions were initially in the early 1970s. Peter Garrison, a contributing editor for Flying magazine, wrote "in my opinion … the most promising engine for aviation use is the Mazda rotary."<ref name="kqNVP">"Revisiting Rotaries", Peter Garrison, Flying, 130, #6 (June 2003), pp. 90 ff.</ref>

The sailplane manufacturer Schleicher uses an Austro Engine AE50R engine<ref name="Austro Engines AR50">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="Austro Engines AR50 and IAE50R-AA">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> in its self-launching models ASK-21 Mi, ASH-26E,<ref name="ASH26">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> ASH-25 M/Mi, ASH-30 Mi, ASH-31 Mi, ASW-22 BLE, and ASG-32 Mi.

In 2013, e-Go airplanes, based in Cambridge, United Kingdom, announced that a rotary engine from Rotron Power will power its new single-seater canard aircraft.<ref name="q17tm">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

The DA36 E-Star, an aircraft designed by Siemens, Diamond Aircraft and EADS, employs a series hybrid powertrain with the propeller being turned by a Siemens Template:Convert electric motor. The aim is to reduce fuel consumption and emissions by up to 25%. An onboard Template:Convert Austro Engine engine and generator provide the electricity. A propeller speed reduction unit is eliminated. The electric motor uses electricity stored in batteries, with the generator engine off, to take off and climb reducing sound emissions. The series-hybrid powertrain using the Wankel engine reduces the plane's weight by 100 kg relative to its predecessor. The DA36 E-Star first flew in June 2013, making this the first-ever flight of a series-hybrid powertrain. Diamond Aircraft claims that rotary engine technology is scalable to a 100-seat aircraft.<ref name="RcilK">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="SmURs">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Trains

Since 2015, a total of 60 trains in Germany have been equipped with Wankel-engined auxiliary power systems that burn diesel fuel. The locomotives use the WST KKM 351 Wankel diesel fuel engine.<ref name="auto"/>

Other uses

File:UAV-741-F.jpg

Figure 33.
UEL UAV-741 Wankel engine for AAI RQ-7 Shadow UAV

The Wankel engine is well-suited for devices in which a human operator is close to the engine, e.g., hand-held devices such as chainsaws.<ref name="Ansdale Keller 1971 p. 214">Template:Cite book</ref> The excellent starting behavior and low mass make the Wankel engine also a good powerplant for portable fire pumps and portable power generators.<ref name="Ansdale Keller 1971 p. 215">Template:Cite book</ref>

Small Wankel engines are being found in applications such as go-karts, personal watercraft, and auxiliary power units for aircraft.<ref name="o4ITr">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Kawasaki patented mixture-cooled rotary engine (US patent 3991722). Japanese diesel engine manufacturer Yanmar and Dolmar-Sachs of Germany had a rotary-engined chain saw (SAE paper 760642) and outboard boat engines, and the French Outils Wolf, made a lawnmower (Rotondor) powered by a Wankel rotary engine. The rotor was in a horizontal position to save on production costs, and there were no seals on the downside.

The simplicity of the rotary engine makes it well-suited for mini, micro, and micro-mini engine designs. The Microelectromechanical systems (MEMS) Rotary Engine Lab at the University of California, Berkeley, formerly researched developing rotary engines down to 1 mm in diameter, with displacements less than 0.1 cc. Materials include silicon, and motive power includes compressed air. The goal of such research was to eventually develop an internal combustion engine with the ability to deliver 100 milliwatts of electrical power, with the engine serving as the rotor of the electric generator, with magnets built into the engine rotor.<ref name="zRdO7">Template:Cite journal</ref><ref name="ZZSJW">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Development of the miniature rotary engine stopped at UC Berkeley at the end of the DARPA contract.

In 1976, Road & Track reported that Ingersoll-Rand would develop a Wankel engine with a chamber volume V_k of Template:Cvt with a rated power of Template:Cvt per rotor.<ref name="Road & Track 1976 p. 89">Template:Cite book</ref> Eventually, 13 units of the proposed engine were built, albeit with a larger displacement, and covered over 90,000 operating hours combined. The engine was made with a chamber volume V_k of Template:Cvt, and a power output of Template:Cvt per rotor. Both single, and twin-rotor engines were made (producing Template:Cvt or Template:Cvt respectively). The engines ran on natural gas and had a relatively low engine speed due to its application.<ref name="The Rotary Combustion Engine: A Candidate for General Aviation 1978 p. 127">Template:Cite book</ref>

Deere & Company acquired the Curtiss-Wright rotary division in February 1984, making large multi-fuel prototypes, some with an 11-liter rotor for large vehicles.<ref name=silvestri/><ref name="DgihD">Template:Citation</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The developers attempted to use a stratified charge concept.<ref name=silvestri>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The technology was transferred to RPI in 1991.<ref>Template:Cite news</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Yanmar of Japan produced small, charge-cooled rotary engines for chainsaws and outboard engines.<ref name="JhAV3">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> One of its products is the LDR (rotor recess in the leading edge of the combustion chamber) engine, which has better exhaust emissions profiles, and reed-valve controlled intake ports, which improve part-load and low rpm performance.<ref name="HMj5q">Template:Citation</ref>

In 1971 and 1972, Arctic Cat produced snowmobiles powered by Sachs KM 914 303-cc and KC-24 294-cc Wankel engines made in Germany.

In the early 1970s, Outboard Marine Corporation sold snowmobiles under the Johnson and other brands, which were powered by Template:Convert OMC engines.

Aixro of Germany produces and sells a go-kart engine with a 294-cc-chamber charge-cooled rotor and liquid-cooled housings. Other makers include Wankel AG, Cubewano, Rotron, and Precision Technology.

Non-internal combustion

File:Wankel-Airco.jpg

Figure 34.
Ogura Wankel Air conditioning system compressor

In addition to applications as an internal combustion engine, the basic Wankel design has also been used for gas compressors, and superchargers for internal combustion engines, but in these cases, although the design still offers advantages in reliability, the primary advantages of the Wankel in size and weight over the four-stroke internal combustion engine are irrelevant. In a design using a Wankel supercharger on a Wankel engine, the supercharger is twice the size of the engine.

The Wankel design is used in the seat belt pre-tensioner system<ref name="DT41N">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> in some Mercedes-Benz<ref name="HcEdw">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> and Volkswagen<ref name="nVs9X">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> cars. When the deceleration sensors detect a potential crash, small explosive cartridges are triggered electrically, and the resulting pressurized gas feeds into tiny Wankel engines, which rotate to take up the slack in the seat belt systems, anchoring the driver and passengers firmly in the seat before a collision.<ref name="5FrID">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

See also

• General Motors Rotary Combustion Engine
• Gunderson Do-All Machine
• Mazda RX-8 Hydrogen RE
• Mazda Wankel engine
• Mercedes-Benz M 950
• Mercedes-Benz C111
• O.S. Engines, the only licensed maker of Wankel model engines
• Pistonless rotary engine
• RKM engine
• Liquidpiston

References

• Template:Cite book
• Template:Cite book
• Template:Cite journal
• Template:Cite book
• Template:Cite book
• F Feller and M I Mech: "The 2-Stage Rotary Engine—A New Concept in Diesel Power" by Rolls-Royce, The Institution of Mechanical Engineers, Proceedings 1970–71, Vol. 185, pp. 139–158, D55-D66. London
• Template:Cite book
• P V Lamarque, "The Design of Cooling Fins for Motor-Cycle Engines", The Institution of Automobile Engineers Magazine, London, March 1943 issue, and also in "The Institution of Automobile Engineers Proceedings", XXXVII, Session 1942–1943, pp. 99–134 and 309–312.
• Walter G. Froede (1961): 'The NSU-Wankel Rotating Combustion Engine', SAE Technical paper 610017
• M. R. Hayes & D. P. Bottrill: 'N.S.U. Spider -Vehicle Analysis', Mira (Motor Industry Research Association, UK), 1965.
• C Jones (Curtiss-Wright), "Rotary Combustion Engine is as Neat and Trim as the Aircraft Turbine", SAE Journal, May 1968, Vol 76, nº 5: 67–69. Also in SAE paper 670194.
• Jan P Norbye: "Rivals to the Wankel", Popular Science, Jan 1967; 'The Wankel Engine. Design, development, applications'; Chilton, 1972. Template:ISBN
• Template:Cite book
• T W Rogers et al. (Mobil), "Lubricating Rotary Engines", Automotive Engineering (SAE) May 1972, Vol 80, nº 5: 23–35.
• K Yamamoto et al. (Mazda): "Combustion and Emission Properties of Rotary Engines", Automotive Engineering (SAE), July 1972: 26–29. Also in SAE paper 720357.
• L W Manley (Mobil): "Low-Octane Fuel is OK for Rotary Engines", Automotive Engineering (SAE), Aug 1972, Vol 80, nº 8: 28–29.
• Template:Cite book
• Reiner Nikulski: "The Norton rotor turns in my Hercules W-2000", "Sachs KC-27 engine with a catalyst converter", and other articles in: "Wankel News" (In German, from Hercules Wankel IG)
• "A WorldWide Rotary Update", Automotive Engineering (SAE), Feb 1978, Vol 86, nº 2: 31–42.
• B Lawton: 'The Turbocharged Diesel Wankel Engine', C68/78, of: 'Institution of Mechanical Engineers Conference Publications. 1978–2, Turbocharging and Turbochargers, Template:ISBN, pp 151–160.
• T Kohno et al. (Toyota): "Rotary Engine's Light-Load Combustion Improved", Automotive Engineering (SAE), Aug 1979: 33–38. Also in SAE paper 790435.
• Kris Perkins: Norton Rotaries, 1991 Osprey Automotive, London. Template:ISBN
• Karl Ludvigsen: Wankel Engines A to Z, New York 1973. Template:ISBN
• Len Louthan (AAI corp.): 'Development of a Lightweight Heavy Fuel Rotary Engine', SAE paper 930682
• Template:Citation
• Patents: Template:Patent, 1958 -Wankel; Template:Patent, 1974 -Kawasaki; Template:Patent, 1974 -Ford; Template:Patent, 1974; Template:Patent, 1976 -Ford; Template:Patent, 1978; Template:Patent, 1979 -Ford.
• Dun-Zen Jeng et al.: 'The Numerical Investigation on the Performance of Rotary Engine with Leakage, Different Fuels and Recess Sizes', SAE paper 2013-32-9160, and same author: 'The intake and Exhaust Pipe Effect on Rotary Engine Performance', SAE paper 2013-32-9161
• Wei Wu et al.: 'A Heat Pipe Assisted Air-Cooled Rotary Wankel Engine for Improved Durability, Power and Efficiency', SAE paper 2014-01-2160
• Alberto Boretti: 'CAD/CFD/CAE Modelling of Wankel Engines for UAV', SAE Technical Paper 2015-01-2466
• Template:Cite book

External links

• {{#if:2988008

|[{{#ifeq:|uspto|http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=%7Chttps://patents.google.com/patent/US}}{{#iferror:{{#expr:2988008 }}|2988008}} U.S. patent {{#ifeq:Template:Replace|Template:Digits|Template:Replace|2988008}}] |{{US patent|123456|link text}}}}

• {{#invoke:citation/CS1|citation

|CitationClass=web }}

• Template:Cite magazine
• Template:Cite magazine
• {{#invoke:citation/CS1|citation

|CitationClass=web }}