Editing Air-start system (section)

==Diesel engines==
===Direct starting===
Compared to a [[gasoline]] (petrol) engine, a [[diesel engine]] has a very high [[compression ratio]], an essential design feature, as it is the heat of compression that ignites the fuel. An electric starter with sufficient power to turn a large diesel engine would itself be so large as to be impractical so there is a need for an alternative system.

An air start system has three main components along with various safety components, namely the air start injector, the distributor and the air receivers. When the system is initiated, starting air from the receivers is distributed by the distributor unit to each respective air start valve according to the firing order of the engine’s cylinders. Safety components include flame traps, to prevent air line explosions, a turning gear interlock which ensures that air-start cannot be initiated when the turning gear is engaged, relief valves and isolation valves, as well as drain valves at certain points along the system. Control components include the control valves and remote air-start valves.<ref>{{cite web| url=http://machineryspaces.com/starting-air-system.html|title=Starting air system for Marine diesel engine|publisher=MachinerySpaces.com|access-date=6 March 2023|archive-date=15 December 2022|archive-url=https://web.archive.org/web/20221215161933/http://www.machineryspaces.com/starting-air-system.html}}</ref> A direct start system as used on a marine slow-speed diesel is required to have up to 12 starts on a non-reversing engine or 6 starts on a reversible, or geared, engine.

When starting the engine, [[compressed air]] is admitted to whichever cylinder has a [[piston]] just over [[four stroke cycle|top dead center]], forcing it downward.<ref>{{cite web |url=http://www.marinediesels.info/2_stroke_engine_parts/Other_info/air_start.htm |title=The air start system at marinediesels.co.uk How a marine diesel engine starts using compressed air |publisher=Marinediesels.info |access-date=2013-04-15 |archive-date=2013-04-28 |archive-url=https://web.archive.org/web/20130428153825/http://www.marinediesels.info/2_stroke_engine_parts/Other_info/air_start.htm |url-status=dead }}</ref> As the engine starts to turn, the air-start valve on the next cylinder in line opens to continue the rotation. After several rotations, fuel is injected into the cylinders, the engine starts running and the air is cut off.

To further complicate matters, a large engine is usually "blown over" first with zero fuel settings and the indicator cocks open, to prove that the engine is clear of any water build up and that everything is free to turn. After a successful blow ahead and a blow astern, the indicator cocks are closed on all the cylinders, and then the engine can be started on fuel. Significant complexity is added to the engine by using an air-start system, as the [[cylinder head]] must have an extra valve in each cylinder to admit the air in for starting, plus the required control systems. This added complexity and cost limits the use of air-starters to very large and expensive reciprocating engines.
[[File:VideoGaliAir.webm|thumb|Air starter on Caterpillar Diesel Engine]]

===Starter motor===
Another method of air-starting an internal combustion engine is by using compressed air or gas to drive a fluid motor in place of an electric motor.<ref>{{cite web |title=Air Starters |url=https://www.galigrup.com/en/producto/components-for-diesel-and-gas-engines/air-starter/ |access-date=2023-11-07 |website=GALI |publisher=galigrup.com}}</ref> They can be used to start engines from 5 to 320 liters in size and if more starting power is necessary two or more motors can be used. Starters of this type are used in place of electric motors because of their lighter weight and higher reliability. They can also outlast an electric starter by a factor of three and are easier to rebuild. Engines operating in underground mining activities tend to operate on this type of starter system to reduce the risk of an electrical system igniting flammable material.

All vane type air starters should have a lubricator installed to insure long-life and maximum performance.<ref>{{cite web|url=https://ascairstarter.com/bdKeJO22q0Jjw/?page_id=20|title=Frequently asked questions|website=Air Starter Components}}</ref> Lubricators give the moving parts a needed friction barrier, reduce metal corrosion and keep vanes sealed properly against the cylinder walls. Even the so-called lube-free air starters require lubrication to prolong trouble free life. Two basic lubricator devices are typically employed. One is an in-line or reservoir type that typically stores up to 2 quarts of lubricant, and is installed along the air supply line. The second style of lubricator is a small one shot device that dispenses a measured amount of lubricant every time the starter is engaged. Installed directly onto the air inlet of the starter, the in-line lubricators are self priming pneumatic pumps that require a 1/4″ lubrication line piped from as far away as 4 feet. Air Starter lubricators perform best using misting type, non-detergent oils such as diesel fuel or Marvel Mystery oil. If emissions are a concern, there are environmentally friendly type lubricants available on the market.

Not all air starters require lubrication.  Turbine type air starters do not require air motor lubrication, although some turbine air starters do use an oil filled transmission that may require periodic inspections and maintenance.