Editing Timer (section)

==Hardware==

===Mechanical===
Mechanical timers use [[clockwork]] to measure time.<ref name="Sobey">{{cite book 
 | last = [[Ed Sobey|Sobey]]
 | first = Ed 
 | title = The Way Kitchens Work: The Science Behind the Microwave, Teflon Pan, Garbage Disposal, and More 
 | publisher = Chicago Review Press
 | year = 2021
 | location = UK
 | pages = 161–164
 | url = https://books.google.com/books?id=RDfCMTQPMucC&q=%22timer%22+%22balance+wheel%22&pg=PA164
 | isbn = 978-1569762813}}</ref> Manual timers are typically set by turning a dial to the time interval desired, turning the dial stores energy in a [[mainspring]] to run the mechanism. They function similarly to a mechanical [[alarm clock]], the energy in the mainspring causes a [[balance wheel]] to rotate back and forth. Each swing of the wheel releases the gear train to move forward by a small fixed amount, causing the dial to move steadily backward until it reaches zero when a lever arm strikes a bell. The mechanical kitchen timer was invented in 1926.

The simplest and oldest type of mechanical timer is the hourglass - which is also known as "the glass of the hour" - in which a fixed amount of sand drains through a narrow opening from one chamber to another to measure a time interval.

===Electromechanical===
[[File:Electromechanicaltimer.JPG|thumb|An electromechanical timer]]
Short-period [[bimetallic strip|bimetallic]] [[Electromechanics|electromechanical]] timers use a thermal mechanism, with a metal finger made of strips of two metals with different rates of [[thermal expansion]] sandwiched together, steel and bronze are common. An [[electric current]] flowing through this finger causes heating of the metals, one side expands less than the other, and an electrical contact on the end of the finger moves away from or towards an electrical switch contact. The most common use of this type is in the "flasher" units that flash [[turn signal]]s in [[automobile]]s, and sometimes in [[Christmas lights (holiday decoration)|Christmas lights]]. This is a non-electronic type of [[multivibrator]].

An electromechanical [[cam timer]] uses a small [[Synchronous motor|synchronous]] [[Alternating current|AC]] [[electric motor|motor]] turning a cam against a comb of switch contacts. The AC motor is turned at an accurate rate by the alternating current, which power companies carefully regulate. [[Gear]]s drive a shaft at the desired rate, and turn the cam. The most common application of this timer now is in [[Washing machine|washer]]s, [[Clothes dryer|driers]] and [[dishwasher]]s. This type of timer often has a friction clutch between the gear train and the cam, so that the cam can be turned to reset the time.

Electromechanical timers survive in these applications because mechanical switch contacts may still be less expensive than the semiconductor devices needed to control powerful lights, motors and heaters.

In the past, these electromechanical timers were often combined with electrical [[relay]]s to create electro-mechanical controllers. Electromechanical timers reached a high state of development in the 1950s and 1960s because of their extensive use in aerospace and weapons systems. Programmable electromechanical timers controlled launch sequence events in early [[rocket]]s and ballistic [[missile]]s. As digital electronics has progressed and dropped in price, electronic timers have become more advantageous.

Electronic timers are essentially quartz clocks with special electronics, which can achieve higher precision than mechanical timers. They have digital electronics, but may have an analog or digital display. Integrated circuits have made digital logic so inexpensive that an electronic timer is now less expensive than many mechanical and electromechanical timers. Individual timers are implemented as a simple single-chip computer system, similar to a watch and usually utilizing the same, mass-produced technology.

Nowadays, many timers are implemented in software. Modern controllers use a programmable logic controller (PLC) instead of a box full of electromechanical parts. The logic is usually designed as if it were relays, utilizing a special computer language called ladder logic. In PLCs, timers are usually simulated by the software built into the controller. Each timer is just an entry in a table maintained by the software.

Computer systems typically have at least one hardware timer. These are typically digital counters that either increment or decrement at a fixed frequency, which is often configurable, and which interrupt the processor when reaching zero. An alternative design uses a counter with a sufficiently large word size that it will not reach its overflow limit before the end of life of the system.

More sophisticated timers may have comparison logic to compare the timer value against a specific value set by software, which triggers some action when the timer value matches the preset value. This might be used, for example, to measure events or generate pulse-width modulated waveforms to control the speed of motors (using a class D digital electronic amplifier).

One specialist use of hardware timers in computer systems is as watchdog timers, which are designed to perform a hardware reset of the system if the software fails.