Editing Interrupt (section)

===Shared IRQs===
{{POV section|date=December 2021}}

Multiple devices may share an edge-triggered interrupt line if they are designed to. The interrupt line must have a pull-down or pull-up resistor so that when not actively driven it settles to its inactive state, which is the default state of it. Devices signal an interrupt by briefly driving the line to its non-default state, and let the line float (do not actively drive it) when not signaling an interrupt. This type of connection is also referred to as [[open collector]]. The line then carries all the pulses generated by all the devices. (This is analogous to the [[pull cord]] on some buses and trolleys that any passenger can pull to signal the driver that they are requesting a stop.) However, interrupt pulses from different devices may merge if they occur close in time. To avoid losing interrupts the CPU must trigger on the trailing edge of the pulse (e.g. the rising edge if the line is pulled up and driven low). After detecting an interrupt the CPU must check all the devices for service requirements.

Edge-triggered interrupts do not suffer the problems that level-triggered interrupts have with sharing. Service of a low-priority device can be postponed arbitrarily, while interrupts from high-priority devices continue to be received and get serviced. If there is a device that the CPU does not know how to service, which may raise spurious interrupts, it will not interfere with interrupt signaling of other devices. However, it is easy for an edge-triggered interrupt to be missed - for example, when interrupts are masked for a period - and unless there is some type of hardware latch that records the event it is impossible to recover. This problem caused many "lockups" in early computer hardware because the processor did not know it was expected to do something. More modern hardware often has one or more interrupt status registers that latch interrupts requests; well-written edge-driven interrupt handling code can check these registers to ensure no events are missed.

The [[Industry Standard Architecture]] (ISA) bus uses edge-triggered interrupts, without mandating that devices be able to share IRQ lines, but all mainstream ISA motherboards include pull-up resistors on their IRQ lines, so well-behaved ISA devices sharing IRQ lines should just work fine. The [[parallel port]] also uses edge-triggered interrupts. Many older devices assume that they have exclusive use of IRQ lines, making it electrically unsafe to share them.

There are three ways multiple devices "sharing the same line" can be raised. First is by exclusive conduction (switching) or exclusive connection (to pins). Next is by bus (all connected to the same line listening): cards on a bus must know when they are to talk and not talk (i.e., the ISA bus). Talking can be triggered in two ways: by accumulation latch or by logic gates. Logic gates expect a continual data flow that is monitored for key signals. Accumulators only trigger when the remote side excites the gate beyond a threshold, thus no negotiated speed is required. Each has its speed versus distance advantages. A trigger, generally, is the method in which excitation is detected: rising edge, falling edge, threshold ([[oscilloscope]] can trigger a wide variety of shapes and conditions).

Triggering for software interrupts must be built into the software (both in OS and app). A 'C' app has a trigger table (a table of functions) in its header, which both the app and OS know of and use appropriately that is not related to hardware. However do not confuse this with hardware interrupts which signal the CPU (the CPU enacts software from a table of functions, similarly to software interrupts).

====Difficulty with sharing interrupt lines====
Multiple devices sharing an interrupt line (of any triggering style) all act as spurious interrupt sources with respect to each other. With many devices on one line, the workload in servicing interrupts grows in proportion to the number of devices. It is therefore preferred to spread devices evenly across the available interrupt lines. Shortage of interrupt lines is a problem in older system designs where the interrupt lines are distinct physical conductors. Message-signaled interrupts, where the interrupt line is virtual, are favored in new system architectures (such as [[PCI Express]]) and relieve this problem to a considerable extent.

Some devices with a poorly designed programming interface provide no way to determine whether they have requested service. They may lock up or otherwise misbehave if serviced when they do not want it. Such devices cannot tolerate spurious interrupts, and so also cannot tolerate sharing an interrupt line. [[Industry Standard Architecture|ISA]] cards, due to often cheap design and construction, are notorious for this problem. Such devices are becoming much rarer, as [[hardware logic]] becomes cheaper and new system architectures mandate shareable interrupts.