Editing Table saw (section)

==Accessories==
* ''Outfeed tables:'' Table saws are often used to rip long boards or sheets of plywood or other sheet materials. The use of an out feed (or outfeed) table makes this process safer and easier. Many of these are shop built, while others are commercially available.
* ''Infeed tables:'' Used to assist feeding long boards or sheets of plywood. In the past roller stands were pretty much the only option, but there are now commercially available infeed units that are more efficient and easier to use.
* ''[[Downdraft table]]s:'' Used to draw harmful dust particles away from the user without obstructing the user's movement or productivity.
* ''{{visible anchor|Rip fence}}'': Table saws commonly have a fence (guide) running from the front of the table (the side nearest the operator) to the back, parallel to the cutting plane of the blade. The distance of the fence from the blade can be adjusted, which determines where on the workpiece the cut is made. The fence is commonly called a "rip fence" referring to its use in guiding the workpiece during the process of making a [[rip cut]]. Most table saws come standard with a rip fence, but some high end saws are available without a fence so a fence of the user's choice can be purchased separately.
* ''[[Featherboard]]:'' Featherboards are used to keep wood against the rip fence. They can be a single spring, or many springs, as made from wood in many shops. They are held in place by high strength magnets, clamps, or expansion bars in the miter slot.
* ''Hold down:'' The circular sawblade of a tablesaw will pick up a piece of wood if not held down. Hold downs can be a vertical version of featherboards, attached to a fence with magnets or clamps. Another type of hold down uses wheels on a spring-loaded mechanism to push down on a workpiece as it is guided past the blade.
* ''Sub fence:'' A piece of wood clamped to the rip fence allows a dado set to cut into the rip fence, allowing rabbet cuts with a dado blade.
* ''Miter gauge:'' The table has one or two slots (grooves) running from front to back, also parallel to the cutting plane of the blade. These miter slots (or miter grooves) are used to position and guide either a [[miter gauge]] (also known as a crosscut fence) or crosscut sled. The miter gauge is usually set to be at 90 degrees to the plane of the blade's cut, to cause the cut made in the workpiece to be made at a right angle. The miter gauge can also be adjusted to cause the cut to be made at a precisely controlled angle (a so-called miter cut).
* ''Crosscut sled:'' A crosscut sled is generally used to hold the workpiece at a fixed 90-degree angle to the blade, allowing precise repeatable cuts at the most commonly used angle. The sled is normally guided by a runner fastened under it that slides in a miter slot. This device is normally shop made, but can be purchased.
* ''Tenon jig:'' A tenon jig is a device that holds the workpiece vertically so cuts can be made across the end. This allows tenons to be formed. Often this is a purchased item, but it can be shop made. The tenon jig is guided by a miter slot or a fence.
* ''Stacked dado:'' Saws made for the US market are generally capable of using a [[dado set|stacked dado]] blade set. This is a kit with two outer blades and a number of inner [[chip breaker]]s that can be used to cut dados (grooves in the workpiece) of any width up to the maximum (generally {{cvt|13/16|in|disp=sqbr}}). Stacked dado sets are available in diameters of {{convert|6|,|8|and|10|in}}. 8- and 10-inch stacked dado sets are not recommended for saws with {{convert|1+1/2|hp}} or less. Although 10-inch stacked dado sets are available with a {{convert|5/8|in|adj=on}} bore, these are recommended with a {{convert|1|in|adj=on}} bore.
* ''Inserts:'' Table saws have a changeable insert in the table through which the blade projects. Purchasable inserts are usually made out of metal. Zero-clearance inserts can be made of a sawable material such as plastic or wood. When a zero-clearance insert is initially inserted, the blade is raised through the insert creating the slot. This creates a slot with no gaps around the blade. The zero clearance insert helps prevent tearout by providing support for wood fibers right next to the blade thus helping to make a very clean cut. Other inserts can be bought or created in the same manner, such as a dado insert.
* ''Splitter:'' A splitter or [[riving knife]] is a vertical projection located behind the saw blade. This can be a pin or a fin. It is slightly narrower in width than the blade and located directly in line with the blade. The splitter prevents the material being cut from being rotated thereby helping to prevent kickback. Splitters may incorporate pawls, a mechanism with teeth designed to bite into wood and preventing kickback. Splitters can take many forms, including being part of the blade guard that comes standard with the saw. Another type of splitter is simply a vertical pin or fin attached to an insert. Splitters are available commercially or can be made from wood, metal or plastic.
* ''Anti-kickback pawls:'' Most modern US table saws are fitted with kickback pawls, a set of small spring-loaded metal teeth on a free-swinging pawl (usually attached to the guard) which help to put a strong downward force on a board. This can help to immobilize the board in the event of a kickback. However, these have sometimes been found to be somewhat ineffective when compared to a splitter.
*''[[Push stick]]:'' A handheld safety device used to safely maneuver a workpiece, keeping it flat against the machine table and fence while it is being cut.