Editing Diesel engine (section)

=== Thermodynamic cycle ===
{{technical|section|date=July 2022}}
[[File:Model Engine Luc Viatour.jpg|thumb|Diesel engine model, left side]]
[[File:Model Engine B Luc Viatour.jpg|thumb|Diesel engine model, right side]]
{{See also|Diesel cycle|Reciprocating internal combustion engine}}

The diesel internal combustion engine differs from the gasoline powered [[Otto cycle]] by using highly compressed hot air to ignite the fuel rather than using a spark plug (''compression ignition'' rather than ''spark ignition'').

In the diesel engine, only air is initially introduced into the combustion chamber. The air is then compressed with a compression ratio typically between 15:1 and 23:1. This high compression causes the temperature of the air to rise. At about the top of the compression stroke, fuel is injected directly into the compressed air in the combustion chamber. This may be into a (typically [[toroid]]al) void in the top of the piston or a ''pre-chamber'' depending upon the design of the engine. The fuel injector ensures that the fuel is broken down into small droplets, and that the fuel is distributed evenly. The heat of the compressed air vaporises fuel from the surface of the droplets. The vapour is then ignited by the heat from the compressed air in the combustion chamber, the droplets continue to vaporise from their surfaces and burn, getting smaller, until all the fuel in the droplets has been burnt. Combustion occurs at a substantially constant pressure during the initial part of the power stroke. The start of vaporisation causes a delay before ignition and the characteristic diesel knocking sound as the vapour reaches ignition temperature and causes an abrupt increase in pressure above the piston (not shown on the P-V indicator diagram). When combustion is complete the combustion gases expand as the piston descends further; the high pressure in the cylinder drives the piston downward, supplying power to the [[crankshaft]].

As well as the high level of compression allowing combustion to take place without a separate ignition system, a high [[compression ratio]] greatly increases the engine's efficiency. Increasing the compression ratio in a spark-ignition engine where fuel and air are mixed before entry to the cylinder is limited by the need to prevent [[pre-ignition#Pre-ignition|pre-ignition]]<!-- detonation from occurring after ignition and is more a fuel quality or combustion chamber design issue -->, which would cause engine damage. Since only air is compressed in a diesel engine, and fuel is not introduced into the cylinder until shortly before top dead centre ([[Top Dead Center|TDC]]), premature detonation is not a problem and compression ratios are much higher.

[[File:DieselCycle PV.svg|thumb|right|pV diagram for the ideal diesel cycle (which follows the numbers 1–4 in clockwise direction). The horizontal axis is the cylinder volume. In the diesel cycle the combustion occurs at almost constant pressure. On this diagram the work that is generated for each cycle corresponds to the area within the loop.]]
The [[pressure–volume diagram]] (pV) diagram is a simplified and idealised representation of the events involved in a diesel engine cycle, arranged to illustrate the similarity with a [[Carnot cycle]]. Starting at 1, the piston is at bottom dead centre and both valves are closed at the start of the compression stroke; the cylinder contains air at atmospheric pressure. Between 1 and 2 the air is compressed adiabatically&nbsp;– that is without heat transfer to or from the environment&nbsp;– by the rising piston. (This is only approximately true since there will be some heat exchange with the [[Cylinder (engine)|cylinder walls]].) During this compression, the volume is reduced, the pressure and temperature both rise. At or slightly before 2 (TDC) fuel is injected and burns in the compressed hot air. Chemical energy is released and this constitutes an injection of thermal energy (heat) into the compressed gas. Combustion and heating occur between 2 and 3. In this interval the pressure remains constant since the piston descends, and the volume increases; the temperature rises as a consequence of the energy of combustion. At 3 fuel injection and combustion are complete, and the cylinder contains gas at a higher temperature than at 2. Between 3 and 4 this hot gas expands, again approximately adiabatically. Work is done on the system to which the engine is connected. During this expansion phase the volume of the gas rises, and its temperature and pressure both fall. At 4 the exhaust valve opens, and the pressure falls abruptly to atmospheric (approximately). This is unresisted expansion and no useful work is done by it. Ideally the adiabatic expansion should continue, extending the line 3–4 to the right until the pressure falls to that of the surrounding air, but the loss of efficiency caused by this unresisted expansion is justified by the practical difficulties involved in recovering it (the engine would have to be much larger). After the opening of the exhaust valve, the exhaust stroke follows, but this (and the following induction stroke) are not shown on the diagram. If shown, they would be represented by a low-pressure loop at the bottom of the diagram. At 1 it is assumed that the exhaust and induction strokes have been completed, and the cylinder is again filled with air. The piston-cylinder system absorbs energy between 1 and 2&nbsp;– this is the work needed to compress the air in the cylinder, and is provided by mechanical kinetic energy stored in the flywheel of the engine. Work output is done by the piston-cylinder combination between 2 and 4. The difference between these two increments of work is the indicated work output per cycle, and is represented by the area enclosed by the pV loop. The adiabatic expansion is in a higher pressure range than that of the compression because the gas in the cylinder is hotter during expansion than during compression. It is for this reason that the loop has a finite area, and the net output of work during a cycle is positive.<ref name="Reif_2014_18" />