Editing Fish hook (section)

== Hook types ==
[[File:Vishaakje met loden visje - NAVIGO Nationaal Visserijmuseum - 2494.jpg|thumb|Iron fish hook, decorated with a small fish in lead, used for the cod fishery around Iceland, NAVIGO National Fisheries Museum, [[Belgium]]]]
{{Unreferenced section|date=August 2022}}
There are a large number of different types of fish hooks. At the macro level, there are bait hooks, fly hooks and lure hooks. Within these broad categories there are wide varieties of hook types designed for different applications. Hook types differ in shape, materials, points and barbs, and eye type, and ultimately in their intended application. When individual hook types are designed the specific characteristics of each of these hook components are optimized relative to the hook's intended purpose. For example, a delicate dry fly hook is made of thin wire with a tapered eye because weight is the overriding factor. Whereas Carlisle or Aberdeen light wire bait hooks make use of thin wire to reduce injury to live bait but the eyes are not tapered because weight is not an issue. Many factors contribute to hook design, including corrosion resistance, weight, strength, hooking efficiency, and whether the hook is being used for specific types of bait, on different types of lures or for different styles of flies. For each hook type, there are ranges of acceptable sizes. For all types of hooks, sizes range from 32 (the smallest) to 20/0 (the largest).

=== Shapes and names ===
{{Unreferenced section|date=August 2022}}
[[Image:Angeln zubehoer wobbler 01.jpg|thumb|right|Treble hooks attached to [[fishing lure|artificial lures]]]]
[[Image:Green Highlander salmon fly.jpg|thumb|right|A Salmon Fly hook as the foundation for a ''Green Highlander'', a classic salmon [[artificial fly|fly]]]]
Hook shapes and names are as varied as fish themselves. In some cases, hooks are identified by a traditional or historic name, e.g. Aberdeen, Limerick or O'Shaughnessy. In other cases, hooks are merely identified by their general purpose or have included in their name, one or more of their physical characteristics. Some manufacturers just give their hooks model numbers and describe their general purpose and characteristics. For example:
* ''Eagle Claw'': 139 is a Snelled Baitholder, Offset, Down Eye, Two Slices, Medium Wire
* ''Lazer Sharp'': L2004EL is a [[Circle hook|Circle]] Sea, Wide Gap, Non-Offset, Ringed Eye, Light Wire
* ''Mustad Model'': 92155 is a Beak Baitholder hook
* ''Mustad Model'': 91715D is an O'Shaughnessy Jig Hook, 90-degree angle
* ''TMC Model 300'': Streamer D/E, 6XL, Heavy wire, Forged, Bronze
* ''TMC Model 200R'': Nymph & Dry Fly Straight eye, 3XL, Standard wire, Semi-dropped point, Forged, Bronze

The shape of the hook shank can vary widely from merely straight to all sorts of curves, kinks, bends and offsets. These different shapes contribute in some cases to better hook penetration, fly imitations or bait holding ability. Many hooks intended to hold dead or artificial baits have sliced shanks which create barbs for better baiting holding ability. [[Jig (fishing)|Jig]] hooks are designed to have lead weight molded onto the hook shank. Hook descriptions may also include shank length as standard, extra-long, 2XL, short, etc. and wire size such as fine wire, extra heavy, 2X heavy, etc.

==== Single, double and triple hooks ====
Hooks are designed as either ''single'' hooks—a single eye, shank and point; ''double'' hooks—a single eye merged with two shanks and points; or ''triple''—a single eye merged with three shanks and three evenly spaced points. Double hooks are formed from a single piece of wire and may or may not have their shanks brazed together for strength. Treble hooks are formed by adding a single eyeless hook to a double hook and brazing all three shanks together. Double hooks are used on some artificial lures and are a traditional fly hook for Atlantic Salmon flies, but are otherwise fairly uncommon. Treble hooks are used on all sorts of artificial lures as well as for a wide variety of bait applications.

==== Bait hook shapes and names ====
Bait hook shapes and names include the Salmon Egg, Beak, O'Shaughnessy, Baitholder, Shark Hook, Aberdeen, Carlisle, Carp Hook, Tuna Circle, Offset Worm, [[Circle hook|Circle Hook]], suicide hook, Long Shank, Short Shank, J Hook, Octopus Hook and Big Game Jobu hooks.

==== Fly hook shapes and names ====
Fly hook shapes include Sproat, Sneck, Limerick, Kendal, Viking, Captain Hamilton, Barleet, Swimming Nymph, Bend Back, Model Perfect, Keel, and Kink-shank.

=== Points and barbs ===
{{Unreferenced section|date=August 2022}}
[[File:Barbed vs barbless hooks.jpg|thumb|Barbless hook (top) vs. barbed hook (bottom)]]
The hook point is probably the most important part of the hook, because it is the point that must penetrate into the fish's flesh first if the hook is to have any anchorage whatsoever. Both the profile of the hook point and its angulation influence how well the point will pierce the tissue. Hook points are mechanically (ground) or chemically sharpened.

Most modern hooks are ''barbed'', with a backward-protruding spike (i.e. barb) that helps secure the hook anchorge by catching surrounding flesh to stop the point from sliding back out of the penetration. Because the barb increases the practical [[cross-sectional area]] of the hook point, it also negatively affect how far the point penetrates under the same force (especially when piercing harder tissue), although the tissue-grabbing ability of the barb alone is usually sufficient for maintaining the hook anchorage without needing a deep penetration.

Some hooks are ''barbless'', with a simply tapered point and lacking any barb. Historically, ancient fish hooks were all barbless, but today barbless hooks are still used mainly to facilitate quicker hook removal and make [[catch-and-release]] less hurtful for the fish. The downside of barbless hooks is that because there is no barb to help secure the point anchorage, the hook is theoretically more susceptible to dislodging unless the penetration is maintained with a constantly taut line tension. There are however also some arguments that a barbless hook point will penetrate more smoothly into the fish tissue and thus allow a deeper [[hookset]], compensating for the absence of barbs. Having a deeper hookset also means the [[stress (mechanics)|stress]] tends to be concentrated nearer towards the hook's bend rather than the point, allowing it to better withstand a heavier [[mechanical load|pulling load]].

==== Hook point types ====
Hook points are also described relative to their offset from the hook shank. A kerbed hook point is offset to the left, a straight point has no offset and a reversed point is offset to the right.

Hook points are commonly referred to by these names: needle point, rolled-in, hollow, spear, beak, mini-barb, semi-dropped and knife edge. Some other hook point names are used for branding by manufacturers.

=== Eyes ===
[[File:FishHooks.JPG|thumb|(Clockwise from top) A standard J-hook with straight eye, a [[circle hook]] with down-turned (outward angled) eye, and an eyeless Japanese ''[[Tenkara fishing|Tenkara]]'' hook with a spade end.]]
[[Image:HookEyes.jpg|thumb|Up-turned, down-turned and straight hook eyes]]
The '''eye''' of the hook is the widened ring/loop at its proximal end, with a hole where the fishing line (typically the [[fishing line#Sections|leader line]]) is passed through (threaded) for fastening via [[knot]]-tying. Hook eye design is usually optimized for either strength, weight and/or presentation. Typical eye types include:
* '''Ringed eye''' or '''ball eye'''  — a circular loop often with a closely opposed gap between the loop end and the loop base;
* '''Brazed eye''' — like a ringed eye, but the loop end is welded shut fully without any gap;
* '''Tapered eye''' — like a ringed eye, but with a pointed loop end;
* '''Looped eye''' — the loop end is elongated with the extended portion laid parallel to the hook shank;
* '''Needle eye''' — the eye hole is ellipsical, or just a narrow slit.<ref>{{cite web|url=https://fishingbooker.com/blog/fishing-hooks-101-parts-sizes-types/|title=Fishing Hooks 101: Parts, Sizes, Types, and More|date=2021-09-15|publisher=Fishing Booker blog|accessdate=2022-09-01}}</ref>
Most hook eyes are directly knotted to the fishing line and are responsible for relaying the pulling force from the line onto the hook body, but sometimes the line is passed cleanly through the eye and tied directly onto the shank instead of onto the eye loop — this is known as a [[snell knot]] or "snelling", and the eye does not take part in transferring any force, merely serving to restrict line wobbling and knot sliding.  In [[fishing lure]]s, it is also not uncommon to see the hook being linked to the lure via a [[circle cotter|split ring]] through the eye, which allows the hook more [[range of motion]].

Hook eyes can also be categorized into three types according to the angulation of the loop plane against the shank, where hooks with bent/"turned" eyes being more optimized for snelling:
* '''Straight''' — the eye is in-line with the shank;
* '''Up-turned''' — the eye is angled ''away from'' the hook point;
* '''Down-turned''' — the eye is angled ''towards'' the hook point.

Some hooks, such as the traditional Japanese ''[[Tenkara fishing|Tenkara]]'' hooks, lack any opening for the line to be threaded, and are thus '''eyeless'''.  Eyeless hooks instead have a widened "[[spade]] end" to help snelling the line onto the shank without slipping.

=== Size ===
{{Unreferenced section|date=August 2022}}
There are no internationally recognized standards for hooks and thus size is somewhat inconsistent between manufacturers. However, within a manufacturer's range of hooks, hook sizes are consistent.

Hook sizes generally are referred to by a numbering system that places the size 1 hook in the middle of the size range. Smaller hooks are referenced by larger [[integer|whole numbers]] (e.g. 1, 2, 3...). Larger hooks are referenced for size increases by increasing whole numbers followed by a "/" and a "0" (i.e. sizes ''over zero''), for example, 1/0 (read as "one nought"), 2/0, 3/0.... The numbers represent relative sizes, normally associated with the gap (the distance from the point tip to the shank). The smallest size available is 32 and largest is 20/0.