Open main menu
Home
Random
Recent changes
Special pages
Community portal
Preferences
About Wikipedia
Disclaimers
Incubator escapee wiki
Search
User menu
Talk
Dark mode
Contributions
Create account
Log in
Editing
Military Grid Reference System
(section)
Warning:
You are not logged in. Your IP address will be publicly visible if you make any edits. If you
log in
or
create an account
, your edits will be attributed to your username, along with other benefits.
Anti-spam check. Do
not
fill this in!
==Numerical location== The third part of an MGRS coordinate is the ''numerical location'' within a 100,000 meter square, given as ''n'' + ''n'' digits, where ''n'' is 1, 2, 3, 4, or 5. If 5 + 5 digits is used, the first 5 digits give the easting in meters, measured from the left edge of the square, and the last 5 digits give the northing in meters, measured from the bottom edge of the square. The resolution in this case is 1 meter, so the MGRS coordinate would represent a 1-meter square, where the easting and northing are measured to its southwest corner. If a resolution of 10 meters is enough, the final digit of the easting and northing can be dropped, so that only 4 + 4 digits are used, representing a 10-meter square. If a 100-meter resolution is enough, 3 + 3 digits suffice; if a 1 km resolution is enough, 2 + 2 digits suffice; if 10 km resolution is enough, 1 + 1 digits suffice. 10 meter resolution (4 + 4 digits) is sufficient for many purposes, and is the NATO standard for specifying coordinates. If we zoom in on Hawaii (figure 2), we see that the square that contains Honolulu, if we use 10 km resolution, would be written 4QFJ15. If the grid zone or 100,000-meter square are clear from context, they can be dropped, and only the numerical location is specified. For example: *If every position being located is within the same grid zone, only the 100,000-meter square and numerical location are specified. *If every position being located is within the same grid zone and 100,000-meter square, only the numerical location is specified. *However, even if every position being located is within a small area, but the area overlaps multiple 100,000-meter squares or grid zones, the entire grid reference is required. One always reads map coordinates from west to east first (easting), then from south to north (northing). Common mnemonics include "in the house, up the stairs", "left-to-right, bottom-to-top" and "Read Right Up". ===Truncation, not rounding and read more=== As mentioned above, when converting UTM coordinates to an MGRS grid reference, or when abbreviating an MGRS grid reference to lower precision, one should {{em|truncate}} the coordinates, not round. This has been controversial in the past, since the oldest specification, TM8358.1,<ref name="DMA8358_1_Chapter3"/> used rounding, as did GEOTRANS<ref name="Geotrans">[http://earth-info.nga.mil/GandG/geotrans/index.html GEOTRANS] Geographic Translator software and source code from the US National Geospatial-Intelligence Agency.</ref> before version 3.0. However, truncation is used in GEOTRANS since version 3.0, and in NGA Military Map Reading 201<ref name="Military_Map_Reading_201"/> (page 5) and in the US Army Field Manual 3-25.26.<ref name="Field_Manual_3_25_26">[http://www.globalsecurity.org/military/library/policy/army/fm/3-25-26/index.html Map Reading and Land Navigation], U.S. Army Field Manual No. 3-25.26 (see section 4-6).</ref> The civilian version of MGRS, [[USNG]], also uses truncation.<ref name="Cavell">J. Anthony Cavell, [http://www.amerisurv.com/PDF/TheAmericanSurveyor_USNationalGrid-Cavell_June2005.pdf USNG: Getting it right the first time]. ''The American Surveyor,'' June 2005.</ref>
Edit summary
(Briefly describe your changes)
By publishing changes, you agree to the
Terms of Use
, and you irrevocably agree to release your contribution under the
CC BY-SA 4.0 License
and the
GFDL
. You agree that a hyperlink or URL is sufficient attribution under the Creative Commons license.
Cancel
Editing help
(opens in new window)