Editing Distributed-element model

{{short description|Model of electrical circuits which assumes non-uniform currents, voltages, etc. throughout}}
{{hatnote|This article is an example from the domain of electrical systems, which is a special case of the more general [[distributed-parameter system]]s.}}
[[File:Line model Heaviside.svg|thumb|300px|'''Fig.1 Transmission line.''' The distributed-element model applied to a transmission line.]]

In [[electrical engineering]], the '''distributed-element model''' or '''transmission-line model''' of electrical [[Electrical network|circuit]]s assumes that the attributes of the circuit ([[Electrical resistance|resistance]], [[capacitance]], and [[inductance]]) are distributed continuously throughout the material of the circuit.  This is in contrast to the more common [[lumped-element model]], which assumes that these values are lumped into [[electrical component]]s that are joined by perfectly conducting [[wire]]s.  In the distributed-element model, each circuit element is [[infinitesimal]]ly small, and the wires connecting elements are not assumed to be perfect [[Electrical conduction|conductor]]s; that is, they have [[Electrical impedance|impedance]].  Unlike the lumped-element model, it assumes nonuniform [[Electric current|current]] along each branch and nonuniform [[voltage]] along each wire.  

The distributed model is used where the [[wavelength]] becomes comparable to the physical dimensions of the circuit, making the lumped model inaccurate.  This occurs at high [[Frequency|frequencies]], where the wavelength is very short, or on low-frequency, but very long, [[transmission line]]s such as [[overhead power line]]s.

==Applications==
The distributed-element model is more accurate but more complex than the [[lumped-element model]].  The use of infinitesimals will often require the application of [[calculus]], whereas circuits analysed by the lumped-element model can be solved with [[linear algebra]].  The distributed model is consequently usually only applied when accuracy calls for its use.  The location of this point is dependent on the accuracy required in a specific application, but essentially, it needs to be used in circuits where the wavelengths of the signals have become comparable to the physical dimensions of the components.  An often-quoted engineering rule of thumb (not to be taken too literally because there are many exceptions) is that parts larger than one-tenth of a wavelength will usually need to be analysed as distributed elements.<ref>Kaiser, p. 3·2.</ref>

===Transmission lines===
[[Transmission line]]s are a common example of the use of the distributed model.  Its use is dictated because the length of the line will usually be many wavelengths of the circuit's operating frequency.  Even for the low frequencies used on [[power transmission line]]s, one-tenth of a wavelength is still only about 500 kilometres at 60 Hz.  Transmission lines are usually represented in terms of the [[primary line constants]] as shown in figure 1.  From this model, the behaviour of the circuit is described by the [[secondary line constants]], which can be calculated from the primary ones.

The primary line constants are normally taken to be constant with position along the line leading to a particularly simple analysis and model.  However, this is not always the case, variations in physical dimensions along the line will cause variations in the primary constants, that is, they have now to be described as functions of distance.  Most often, such a situation represents an unwanted deviation from the ideal, such as a manufacturing error, however, there are a number of components where such longitudinal variations are deliberately introduced as part of the function of the component.  A well-known example of this is the [[Horn (telecommunications)|horn antenna]].

Where [[Signal reflection|reflection]]s are present on the line, quite short lengths of line can [[Reflections of signals on conducting lines|exhibit effects]] that are simply not predicted by the lumped-element model. A quarter wavelength line, for instance, will [[Quarter wave impedance transformer|transform]] the terminating [[Electrical impedance|impedance]] into its [[Dual impedance|dual]].  This can be a wildly different impedance.

===High-frequency transistors===
[[File:Line model Kelvin.svg|thumb|300px|'''Fig.2.''' The base region of a bipolar junction transistor can be modelled as a simplified transmission line.]]
Another example of the use of distributed elements is in the modelling of the base region of a [[bipolar junction transistor]] at high frequencies.  The analysis of [[charge carrier]]s crossing the base region is inaccurate when the base region is simply treated as a lumped element.  A more successful model is a simplified transmission line model, which includes the base material's distributed bulk resistance and the substrate's distributed capacitance.  This model is represented in figure 2.

===Resistivity measurements===
[[File:Resistivity probes.svg|thumb|left|'''Fig. 3.''' Simplified arrangement for measuring the resistivity of a bulk material with surface probes.]]
In many situations, it is desired to measure [[resistivity]] of bulk material by applying an [[electrode array]] at the surface.  Amongst the fields that use this technique are [[geophysics]] (because it avoids having to dig into the substrate) and the semiconductor industry (for the similar reason that it is non-intrusive) for testing bulk [[silicon wafer]]s.<ref>Lark-Horovitz & Johnson, p. 54.</ref>  The basic arrangement is shown in figure 3, although normally, more electrodes would be used.  To form a relationship between the voltage and current measured on the one hand, and the material's resistivity on the other, it is necessary to apply the distributed-element model by considering the material to be an array of infinitesimal resistor elements.  Unlike the transmission line example, the need to apply the distributed-element model arises from the geometry of the setup, and not from any wave propagation considerations.<ref>Sharma, pp. 210–212.</ref>

The model used here needs to be truly 3-dimensional (transmission line models are usually described by elements of a one-dimensional line).  It is also possible that the resistances of the elements will be functions of the coordinates, indeed, in the geophysical application, it may well be that regions of changed resistivity are the very things that it is desired to detect.<ref>Sharma, p. 211.</ref>
{{Clear}}

===Inductor windings===
[[File:Inductor distributed model.svg|thumb|250px|'''Fig. 4.''' A possible distributed-element model of an inductor. A more accurate model will also require series resistance elements with the inductance elements.]]
Another example where a simple one-dimensional model will not suffice is the windings of an inductor.  Coils of wire have capacitance between adjacent turns (and more remote turns as well, but the effect progressively diminishes). For a single-layer solenoid, the distributed capacitance will mostly lie between adjacent turns, as shown in figure 4, between turns T<sub>1</sub> and T<sub>2</sub>, but for multiple-layer windings and more accurate models distributed capacitance to other turns must also be considered.  This model is fairly difficult to deal with in simple calculations and, for the most part, is avoided.  The most common approach is to roll up all the distributed capacitance into one lumped element in parallel with the inductance and resistance of the coil.  This lumped model works successfully at low frequencies but falls apart at high frequencies where the usual practice is to simply measure (or specify) an overall ''[[Q factor|Q]]'' for the inductor without associating a specific equivalent circuit.<ref>Northrop, pp. 141–142.</ref>

==See also==
* [[Telegrapher's equations]]
* [[Distributed-element circuit]]
* [[Distributed-element filter]]
* [[Warren P. Mason]]

==References==
{{Reflist|2}}

==Bibliography==
* Kenneth L. Kaiser, ''Electromagnetic compatibility handbook'', CRC Press, 2004 {{ISBN|0-8493-2087-9}}.
* Karl Lark-Horovitz, [[Vivian Annabelle Johnson]], ''Methods of experimental physics: Solid state physics'', Academic Press, 1959 {{ISBN|0-12-475946-7}}.
* Robert B. Northrop, ''Introduction to instrumentation and measurements'', CRC Press, 1997 {{ISBN|0-8493-7898-2}}.
* P. Vallabh Sharma, ''Environmental and engineering geophysics'', Cambridge University Press, 1997 {{ISBN|0-521-57632-6}}.

{{DEFAULTSORT:Distributed-Element Model}}
[[Category:Electronic design]]
[[Category:Electronic circuits]]
[[Category:Distributed element circuits]]
[[Category:Conceptual models]]