Editing Ford small block engine

{{more citations needed|date=May 2010}}

{{Infobox automobile engine
| image = Shelby Mustang GT350 engine.jpg
| caption = [[#GT-350|289 K-code]] in a [[Shelby GT350]]
| name = Ford small block
| aka = {{unbulleted list
  | Windsor V8 (informal)<ref>{{cite magazine |url=https://autohistorypreservationsociety.org/1962-1968-260-and-289-cid-windsor-v8/ |title=1962 - 1968 260 and 289 CID "Windsor V8" |magazine=No Limits Magazine |publisher=Automotive History Preservation Society}}</ref><ref>{{cite magazine |url=https://www.classicandsportscar.com/gallery/35-uses-ford-windsor-v8 |title=35 uses of the Ford Windsor V8 |magazine=Classic & Sports Car}}</ref>
  | Challenger V8<ref name="Gunnell 1987" />}}
| manufacturer = [[Ford Motor Company]]
| configuration = [[Naturally aspirated]] 90° V8
| bore = {{unbulleted list
  | 4.000" (289, 302, 351W)
  | 3.800" (260)
  | 3.680" (255)
  | 3.500" (221)
  }}
| stroke = {{unbulleted list
  | 3.500" (351W)
  | 3.000" (302 & 255)
  | 2.870" (221, 260, 289)
  }}
| displacement = {{unbulleted list
  | {{cvt|221|cid|L |sigfig=2}}
  | {{cvt|255|cid|L |sigfig=2}}
  | {{cvt|260|cid|L |sigfig=2}}
  | {{cvt|289|cid|L |sigfig=2}}
  | {{cvt|302|cid|L |sigfig=2}}
  | {{cvt|351|cid|L |sigfig=2}}
  }}
| length = 27.50" (302, 351W){{efn| With 2001 Explorer–style water pump kit (Ford part ''M-8501-A50''). Blocks with older pumps are 1.25" longer.{{cn|date=April 2021}}<!-- If this statement is verified, the entry here should be reversed, with the measurement of 28.75" given for standard blocks and 27.50 in the note for a special water pump kit.-->}}
| width = {{unbulleted list
  | 21.00" (351W)
  | 18.75" (302)
  }}
| height = {{unbulleted list
  | 23.75" (351W){{efn|Ford measures engine height here from the bottom of the oil pan to the top of valve covers, excluding any breathers or oil fill tubes.{{cn|date=April 2021}}}}
  | 20.75" (302)
  }}
| block = {{unbulleted list
  | Cast iron
  | Deck height:
  | 9.480" (1969–70 351W)
  | 9.503" (1971–96 351W)
  | 8.201–8.210" (BOSS 302)
  | 8.206" (221, 260, 289, 302)
  }}
| head = Cast iron
| valvetrain = {{unbulleted list
  | [[Overhead valve engine|Pushrod OHV]]
  | Cast iron cam, Flat tappet (1962–84 302, 1969–93 351W)
  | Steel roller cam & lifters (1985–2001 302, 1994–97 351W)
  }}
| fuelsystem = {{unbulleted list
  | [[Carburetor|Carbureted]] (1962–1985 302, 1969–1991 351W)
  | [[Fuel injection|EFI]] (1988–1997 351W, 1986–2001 all others)
  }}
| fueltype = 87 Octane
| oilsystem = Wet sump
| coolingsystem = [[Water-cooled]]; jacketed block
| power = {{cvt|115–310|hp|kW|0}}
| torque = {{cvt|262–385|lbft|Nm|0}}
| compression = 9.0:1, 9.5:1, 10.5:1, 8.8:1, 8:1
| production = July 1961 – 2002
| predecessor = [[Ford Y-block engine]]
| successor = [[Ford Modular engine]]
}}
The '''Ford small-block''' is a series of 90° [[overhead valve]] [[engine block|small-block]] [[V8]] automobile engines manufactured by the [[Ford Motor Company]] from July 1961 to December 2000.

Designed as a successor to the [[Ford Y-block engine]], it was first installed in the 1962 model year [[Ford Fairlane (Americas)|Ford Fairlane]] and [[Mercury Meteor]]. Originally produced with a displacement of {{cvt|221|cuin|L|1}}, it eventually increased to {{cvt|351|cuin|L|1}} with a taller deck height, but was most commonly sold (from 1968–2000) with a displacement of [[#302|302]] cubic inches (later marketed as the 5.0&nbsp;L).

The [[#289|289]] small block powered Shelby Mustangs to the [[Trans-Am Series]] manufacturers championship in 1965 and 1966, while the [[Ford Boss 302 engine|Boss 302]] version did the same in 1970. The engine won at the [[24 Hours of Le Mans]] twice; once in [[1968 24 Hours of Le Mans|1968]] and once in [[1969 24 Hours of Le Mans|1969]], both times in [[John Wyer#J. W. Automotive Engineering Ltd|JWAE]] [[Mirage (race car)|Mirages]]. Other wins came from engines installed in [[AC Cobra]]s and the [[Shelby Daytona]] coupe.

The small-block was installed in several of Ford's product lines, including the [[Ford Mustang]], [[Mercury Cougar]], [[Ford Torino]], [[Ford Granada (North America)|Ford Granada]], [[Mercury Monarch]], [[Ford LTD (Americas)|Ford LTD]], [[Mercury Marquis]], [[Ford Maverick (1970–1977)|Ford Maverick]], and [[Ford F-150]] truck.

For the 1991 model year, Ford began phasing in the [[Ford Modular engine|Modular V8 engine]] to replace the small-block, beginning in late 1990 with the [[Lincoln Town Car]] and continuing through the decade. The 2001 [[Ford Explorer]] SUV was the last North American installation of the engine, and [[Ford Australia]] used it through 2002 in the [[Ford Falcon (Australia)|Falcon]] and [[Ford Fairlane (Australia)|Fairlane]].

Although sometimes called the "'''Windsor'''" by enthusiasts, Ford never used that designation for the engine line as a whole; it was only adopted well into its run to distinguish the {{cvt|351|cuin|L|1}} version from the {{cvt|351|cuin|L|1}} "[[Ford 335 engine#351 Cleveland|Cleveland]]" version of the [[Ford 335 engine|335-family engine]] that had the same displacement but a significantly different configuration, and only ever used to refer to that specific engine in service materials. The designations for each were derived from the original locations of manufacture: Windsor, Ontario and Cleveland, Ohio.

From 1962 through the 1990s, Ford small blocks engines were [[marinized]] by various companies (except for the {{cvt|255|cuin|L|1}}).

{{As of|2025|June}}, versions of the small-block remain available for purchase from Ford Performance Parts as [[#Crate engines|crate engines]].<ref>{{cite web|url=https://performanceparts.ford.com/engines/#302|title=Ford Performance Parts - Crate Engines |publisher=Ford |access-date=June 1, 2025}}</ref>

==Overview==
The small-block V8 engine was introduced in the 1962 Ford Fairlane and Mercury Meteor cars. Displacing {{cvt|221|cuin|L|1}}, it was designed to save weight, using thin-wall casting for a short-skirt block that does not extend below the centerline of the crankshaft. The engine uses a separate aluminum timing chain cover, which differentiates it from the later Ford 335-series engines that use an integrated timing cover. All Ford small-block engines use two-valve-per-cylinder heads, with "2V" and "4V" designations indicating the number of barrels (or venturi) in the [[carburetor]]. The valves are in-line and use straight, six-bolt valve covers. Coolant is routed out of the block through the intake manifold.

The design was soon bored to {{cvt|260|cuin|L|1}} and again to {{cvt|289|cuin|L|1}}, then stroked to {{cvt|302|cuin|L|1}}, settling on the most common displacement offered until the engine's retirement in 2001, nearly 40 years after the basic block design debuted. Two additional displacements were produced during the engine's history. A {{cvt|351|cuin|L|1}} model was offered from 1969 until 1996. The 351W (so named to distinguish it from the 335-series Cleveland-produced 351C) has a taller deck height than the other engines in the series to avoid excessively short connecting rods. And for a brief time in the early 1980s, a version with a smaller bore diameter that displaced {{convert|255|cuin|L|1}} was produced as Ford struggled with emissions and fuel economy.

In response to the [[Chevrolet Camaro]]'s success in the [[SCCA]] Trans-Am Series, Ford engineers developed a new racing engine from the small block. The first attempt mated a tunnel-port head to a 289 cubic inch block, but the displacement proved to be too small to deliver the desired power. The next iteration of the engine mated an improved head design to the 302 cubic inch block, producing the famous "[[Ford Boss 302 engine|Boss 302]]". The heads from the Boss 302 became the production heads on the 335-series {{cvt|351|cuin|l|0}} "Cleveland" engines, which used the same bore spacing and head bolt configuration as the small block engines.

As the 1980s drew to a close, Ford began designing a new [[OHC]] V8 to replace the small block. The [[Ford Modular engine|Modular 4.6&nbsp;L OHC V8]] debuted in the 1991 Lincoln Town Car, signaling the eventual demise of the OHV Ford small-block. Through the rest of the decade, Ford gradually shifted V8 applications to the Modular engine, with the Mustang transitioning in 1996. Even as the small-block neared the end of its life, development continued, with new cylinder heads introduced for the Ford Explorer in 1997. American sales in new vehicles ended with the 2001 Ford Explorer, but the engine continues to be offered for sale as a crate engine from Ford Racing and Performance Parts.

===Design changes===
All 221, 260, and 289 engines built from July 1961 through August 1964 used a five-bolt bell housing, with all 221s and 260s being of this configuration, while 289s made after August 1964 changed to the six-bolt pattern – a change made to resolve transmission utilization issues, such as the need for larger-diameter clutches.

The block mount pads and the cylinder wall contour of the 221 and 260 engines changed in January–February 1963 with the introduction of the 289 variant – all 221 and 260 engine blocks up to this time featured "corrugated wall" construction with two [[core plug]]s on the side of each bank and engine mount hole pitch distances of 6 inch.

All three block variants from this point on featured the straight wall method of construction, three core plugs, and an engine mount hole pitch distance of seven inches. The corrugated wall method of block construction had caused cleaning difficulties in the foundry from day one and a change was phased in.

==221==
The first version of Ford's modern Ford small block family was called the '''Fairlane V8''',<ref name="Gunnell 1987" />and was introduced for the 1962 model year as an option on the Fairlane and Meteor. It had a displacement of {{cvt|221|cuin|L|1}}, from a {{cvt|3.5|in|mm}} [[bore (engine)|bore]] and {{cvt|2.87|in|mm}} stroke, with wedge [[combustion chamber]]s for superior breathing, and a two-barrel (2V) carburetor. An advanced, compact, thinwall-casting design, it was 24" wide, 29" long, and 27.5" tall (610&nbsp;mm × 737&nbsp;mm × 699&nbsp;mm). It weighed only {{cvt|470|lb|kg}} dry despite its [[cast iron]] construction, making it the lightest and most compact V8 engine of its type of the era.{{cn|date=December 2024}}

In stock form, it has a two-barrel carburetor and a [[compression ratio]] of 8.7:1, permitting the use of regular rather than premium [[gasoline]]. [[Poppet valve|Valve]] diameters were {{cvt|1.59|in|mm}} (intake) and {{cvt|1.388|in|mm}} (exhaust). Rated power and torque ([[Horsepower#SAE gross power|SAE gross]]) were {{cvt|145|hp|kW|0}} at 4,400&nbsp;rpm and {{cvt|216|lbft|Nm|0}} at 2,200&nbsp;rpm.

The 221 was phased out at the end of May 1963 due to lackluster demand following the mid-'62 introduction of the {{cvt|260|cuin|L|1}} "Challenger" V8 based on it. About 371,000 had been produced.

==255==
In the late 1970s, an urgent need to meet [[United States Environmental Protection Agency|EPA]] [[Corporate Average Fuel Economy|CAFE]] standards led to the creation of the {{cvt|255|cuin|L|1}} version for the 1980 model year, essentially a 302 with the cylinder bores reduced to {{cvt|3.68|in|mm|1}}. The 302 was to be phased out and the 255 was to be an interim engine which would remain until the [[Ford Essex V6 engine (Canadian)|new V6]] was in production. Rated power (SAE net) was {{cvt|115|–|122|hp|kW}}, depending on year and application. Cylinder heads, which were specific to this engine, used smaller combustion chambers and valves, and the intake ports were oval whereas the others were all rectangular. The only externally visible clue was the use of an open-runner intake manifold with a stamped-steel lifter valley cover attached to its underside, reminiscent of previous-generation V8 engines, such as the Y-block and the [[Ford MEL engine|MEL]].

It was optional in [[Ford Fox platform|Fox-chassis]] cars including the Mustang and Mercury Capri, Thunderbird, and Fairmont, and was standard equipment in the Ford LTD. Some variants, such as the one used in the [[Mercury Grand Marquis]], were fitted with a variable-venturi carburetor and were capable of highway fuel economy in excess of {{cvt|27|mpgus|km/L mpgimp}}. Due to its dismal overall performance, the 255 was dropped at the end the 1982 model year with 253,000 units manufactured. 302 production continued and the plans to phase it out were dropped.

Applications:
*1980–1981 [[Ford Fairmont]]
*1981–1982 [[Ford F-Series (seventh generation)|Ford F-100]]
*1981–1982 [[Ford Granada (North America)|Ford Granada]]
*1981–1982 [[Ford LTD (Americas)#Third|Ford LTD]]
*1980–1982 [[Ford Mustang (third generation)|Ford Mustang]]
*1980–1982 [[Ford Thunderbird (eighth generation)|Ford Thunderbird]]
*1980–1982 [[Mercury Capri#Second generation (1979–1986)|Mercury Capri]]
*1980–1982 [[Mercury Cougar#Fifth generation (1980–1982)|Mercury Cougar]]
*1981–1982 [[Mercury Marquis#Third generation (1979–1982)|Mercury Marquis]]
*1980–1981 [[Mercury Zephyr]]

==260==
The 260 was the second version of the Fairlane V8, introduced during the middle of the 1962 model year (March 1962) and given the name '''Challenger'''.<ref name="Gunnell 1987">{{cite book|editor=Gunnell, John|title=The Standard Catalog of American Cars 1946–1975| publisher=Kraus Publications|pages=317–373|year=1987|isbn=0-87341-096-3}}</ref> It used the same block as the 221, and the same two-barrel (2V) carburetor, with displacement increased to {{cvt|260|cuin|L|1}} by expanding its bore to {{cvt|3.80|in|mm|0}}. Compression ratio was raised fractionally to 8.8:1. The engine was slightly heavier than the 221, at {{cvt|482|lb|kg|0}}. Rated power (still SAE gross at the time) rose to {{cvt|164|hp|kW|0}} at 4400&nbsp;rpm , with a peak torque of {{cvt|258|lbft|Nm|0}} at 2200&nbsp;rpm.

For the 1962 and 1963 model years, the valve head diameters remained the same as the 221, but for the 1964 model year, they were enlarged to {{cvt|1.67|in|mm|1}} (intake) and {{cvt|1.45|in|mm|}} (exhaust) – a manufacturing economy measure so that both 260 and 289 engines could use the same valves. Although the engine breathed better, and was capable of producing marginally more power, rated power was unchanged.

In 1963, the 260 became the base engine on full-sized Ford sedans. Later in the model year, its availability was expanded to the [[Ford Falcon (North America)|Ford Falcon]] and [[Mercury Comet]]. The early "1964½" Mustang also offered the 260.

Ford ceased production of the 260 at the end of the 1964 model year with approximately 604,000 units having been made.

===XHP-260===
The special [[rally racing|rally]] version of the Falcon and Comet and early AC Cobra [[sports car]]s of 1962 used a high-performance version of the 260 with higher compression, hotter camshaft timing, upgraded connecting rods, valves with larger diameter valve stems, stronger valve springs and a four-barrel carburetor. This engine was rated (SAE gross) {{cvt|260|hp|kW|0}} at 5800&nbsp;rpm and {{cvt|269|lbft|Nm|0}} at 4800&nbsp;rpm . This engine was termed the HP-260 by Ford and was specifically made for [[Carroll Shelby]]. About 100 were produced.

=== Sunbeam Tiger ===
The 1964–1966 [[Sunbeam Tiger]] Mk I used the 260.

Early 1967 Sunbeam Tiger Mk IIs were fitted the 260 until inventory of that engine ran out, after which it was replaced by the 289 cubic inch V8.

==289==
[[File:1966 Ford Mustang 289 Windsor.JPG|thumb|250px|A 289 Ford small-block V8 in a 1965 [[Ford Mustang]]]]

The {{cvt|289|cuin|L|1}} V8 was introduced in April 1963, carrying the '''Challenger''' name over from the 260<ref name="Gunnell 1987" /> and replacing it as the base V8 for full-sized Fords. 

Bore was expanded to {{cvt|4.00|in|mm|1}}, becoming the standard for most small block Ford engines. Stroke remained at 2.87 inches. Weight was {{cvt|506|lb|kg|0}}. It retained the 260's two-barrel carburetor (2V), had a slightly lower 8.7:1 compression ratio, and was rated at {{cvt|195|hp|kW|0}} (SAE gross) at 4,400&nbsp;rpm and {{cvt|285|lbft|Nm|0}} at 2,200&nbsp;rpm.

===D-code===
In 1964, an intermediate performance version of the engine was introduced with a four-barrel carburetor and 9.0:1 compression, rated at {{cvt|210|hp|kW|0}} at 4,400&nbsp;rpm and {{cvt|300|lbft|Nm|0}} at 2,800&nbsp;rpm.

This engine was known as the "D-code", from the letter code used to identify the engine in the [[VIN]], and was an option on the 1965 [[Ford Mustang]].<ref>{{cite web|url=http://www.mustangspecs.com/years/64-65.shtml|title=Mustang Specs (1964 1/2 and 1965)|access-date=March 27, 2014}}</ref><ref>{{cite web|url=http://www.oldride.com/library/1964_mercury_comet.html|title=OldRide 1964 Mercury Comet|access-date=March 27, 2014}}</ref>

The D-code engine is relatively rare, as it was only offered as an optional engine in the latter half of the 1964 model year.{{cn|date=December 2024}}

===Cyclone===
{{clarification needed span|text=This engine|reason=Which engine, the two barrel or the four barrel?|date=December 2024}}was marketed in the 1964 [[Mercury Comet]] Cyclone as the "Cyclone"<ref name="Gunnell 1987" /> and carried a K-code in its Mercury VIN. This is not the same engine as the HiPo K-code engine offered in Ford vehicles.

===C-code===
For 1965, the compression ratio of the base two-barrel 289 was raised to 9.3:1, increasing power to {{cvt|200|hp|kW|0}} at 4,400&nbsp;rpm and torque to {{cvt|282|lbft|Nm|0}} at 2,400&nbsp;rpm.

In 1968, the output was reduced to {{cvt|195|hp}}.

===A-code===
In 1965, compression for the four-barrel (4V) version was increased to 10.0:1, raising output to {{cvt|225|hp|kW|0}} at 4,800&nbsp;rpm and {{cvt|305|lbft|Nm|0}} at 3,200&nbsp;rpm.

The 289-4V was also the engine for the Australian Ford [[Ford XR Falcon|XR Falcon GT]], its first Falcon GT.

===Production numbers===
Around 3,500,000 289-2V and 289-4V engines were made at Cleveland Engine Plant 1 (CEP1) and 800,000 289-2V at Windsor Engine Plant 1 (WEP1) in 1963–1967.

===289 HiPo (K-code)===
[[File:1968 Shelby GT350 engine.JPG|thumb|250px|Ford 289 K-code engine in a [[Shelby Mustang|Shelby GT 350]]: The horizontal orientation of the thermostat housing on the intake manifold is a telltale Windsor feature.]]

A high-performance version of the Challenger 289 engine<ref name="Gunnell 1987" /> was introduced late in the 1963 model year as a special order for Ford Fairlanes. The engine is informally known as the HiPo or the "K-code", after the engine letter used in the VIN code of cars so equipped. It was the only 289 engine available in the intermediate Fairlanes, with lesser-powered cars receiving the 260 V8. Starting in June 1964, it became an option for the Mustang.

The HiPo engine was engineered to increase performance and high-rpm reliability over the standard 289. It had solid valve lifters with more aggressive cam timing; 10.5:1 compression; a dual point centrifugal advance distributor; smaller combustion chamber heads with cast spring cups and screw-in studs; low-restriction exhaust manifolds; and a bigger, manual-choke 595 [[cubic foot per minute|CFM]] carburetor (105 CFM more than the standard 289-4V). The water pump had fewer vanes to minimize high rpm foaming and cavitation, the fuel pump received an extra spring to keep up with high rpm demand, alternator/generator pulleys were larger diameter to slow their relative speeds at high engine revs, and a special fan was fitted.

Bottom-end high-rpm improvements included a flaw-free selected standard block, thicker main bearing caps and crankshaft damper/balancer, larger-diameter rod bolts, a crankshaft made from 80% [[nodular iron]] as opposed to the regular item's 40% (with each one checked for correct 'nodularity' by polishing an area of the rear counterweight and comparing a magnification of that surface against a standard), and increased crankshaft counterweighting to compensate for the heavier connecting rod big ends. (The external counter weighting at the front was split between the crankshaft damper and a supplementary counterweight placed adjacent to the front main bearing journal, all designed to reduce the 'bending moment' in the crankshaft at high-rpm.)

The HiPo equipped with a single 4-barrel [[Autolite]] 4100 carburetor carried [[Horsepower#SAE gross power|SAE gross]] ratings of {{cvt|271|bhp|PS kW|0}} at 6,000&nbsp;rpm and {{cvt|312|lbft|Nm|0}} at 3,400&nbsp;rpm.<ref>{{cite web|url=http://www.thecarsource.com/fords/engines/289engine.shtml|website=thecarsource.com|title=289 engines|access-date=July 12, 2018}}</ref>

The K-code HiPo engine was an expensive option, and its popularity was greatly diminished after the [[Ford FE engine|390 and 428 big-block engines]] became available in the Mustang and Fairlane lines, which offered similar power, lower cost, and cheaper maintenance at the expense of greater weight and a more unbalanced front/rear weight distribution.

====GT-350====
The HiPo engine was used in modified form by [[Carroll Shelby]] for the 1965–1967 [[Shelby Mustang#1965–1966 Shelby GT350|Shelby GT350]], receiving special exhaust headers, an aluminum intake manifold, and a larger 4-barrel [[Holley Performance Products|Holley]] 715 CFM carburetor, which raised rated power to {{cvt|306|bhp|PS kW|0}} at 6,000&nbsp;rpm and {{cvt|329|lbft|Nm|0}} at 4,200&nbsp;rpm of [[Machine torque|torque]].<ref>{{cite web|url=https://www.ultimatecarpage.com/car/201/Ford-Shelby-Mustang-GT350.html|website=ultimatecarpage.com|title=1965 - 1966 Ford Shelby Mustang GT350|access-date=June 23, 2018}}</ref><ref>{{cite web|url=https://www.myclassicgarage.com/knowledge-base/1965-Ford-Mustang|website=myclassicgarage.com|title=1965 Ford Mustang|access-date=June 23, 2018}}</ref> Shelby also replaced the internal front press-in oil gallery plugs with threaded plugs to reduce chances of high rpm failure, and installed a larger oil pan with baffles to reduce oil starvation in hard cornering.

From 1966 to 1968, Shelby offered an optional [[Paxton Automotive|Paxton]] [[supercharger]] on Shelby GT350 289s, raising power to around {{cvt|390|hp|kW|0}}.{{cn|date=May 2024}}

====Production numbers====
About 25,000 K-code 289s were manufactured at Cleveland Engine Plant 1 (CEP1) between March 1963 and June 1967.

==302==<!-- This section is linked from [[Ford Mustang]] -->
The [[Ford GT40]] MKII had dominated the 24 Hours of Le Mans in 1966, and the GT40 MKIV did likewise in 1967, using various versions of the Ford medium block [[Ford FE engine|FE engine]]. In an attempt to bring top speeds down, the organizers of this race capped engine capacity at 5.0-liters in 1968. With Ford's large-displacement cars obsoleted, Ford Advanced Vehicles was closed in 1966. [[John Wyer]] established J. W. Automotive Engineering Ltd and built a car called the Mirage that was based on the small block MkI GT40, but with displacement increased to {{cvt|302|cuin|L|1}}.

{{clarification needed span|text=Since Ford had ruled that the GT40 engines must have a direct link back to its production cars,|reason=What is this passage on about? Meeting some homologation requirement? If so, it needs to be made clearer, and properly cited.|date=August 2024}} the 302 was adopted in domestic manufacturing.{{citation needed|date=November 2016}} Both two-bolt and four-bolt main bearing versions were made.

===2-Bolt main bearing caps===
[[File:1968 Mercury Cougar convertible 302 4V Windsor.JPG|thumb|A 302 V8 with a 4-barrel carburetor (designated "4V") in a 1968 [[Mercury Cougar]]]]

In 1968, the small-block's stroke was increased from {{cvt|2.87|in|mm|1}} to {{cvt|3|in|mm|1}}, giving a total displacement of {{cvt|4942|cc|L cuin|1}}. The connecting rods were shortened to permit the use of the same pistons as the 289. The new 302 replaced the 289 early in the 1968 model year.

The most common form of this engine used a two-barrel carburetor, initially with 9.5:1 compression. It had [[hydraulic lifters]] and valves of {{cvt|1.773|in|mm}} (intake) and {{cvt|1.442|in|mm}} (exhaust), and was rated (SAE gross) at {{cvt|220|hp|kW|0}} at 4,600&nbsp;rpm and {{cvt|300|lbft|Nm|0}} at 2,600&nbsp;rpm. An optional four-barrel version was rated at {{cvt|230|hp|kW|0}} at 4,800&nbsp;rpm.

The 302 was primarily manufactured at Ford's Cleveland engine plant in Brook Park, Ohio, just as its predecessors were, though Windsor Engine No. 2 manufactured truck-spec engines from 1982 to 1996.<ref>{{cite book |title=The Official 5.0 Mustang Technical Reference & Performance Handbook |first=Al |last=Kirschenbaum |page=174–175}}</ref> The 302 received several changes over the course of its production run, including longer valve stems with rotating lash caps, bottle neck type rocker studs for a positive stop nut arrangement and a longer pushrod to correct valve train geometry. The water pump borrowed from the 351 Cleveland, with a few minor alterations to the casting, allowed the use of a left hand water inlet, which improved water circulation in the radiator to a more cross-flow direction. This change also necessitated moving the timing marks on the harmonic damper to the other side of the front timing cover, and a change to four bolts holding the crank pulley instead of three.

[[Automobile emissions control|Emission regulations]] caused a progressive reduction in compression ratio for the 302 two-barrel, to 9.0:1 in 1972, reducing SAE gross horsepower to {{cvt|210|hp|kW|0}}. In that year, U.S. automakers began to quote horsepower in SAE net ratings; the 302 two-barrel carried a net rating of {{cvt|140|hp|kW|0}}. By 1975, its power had dropped as low as {{cvt|122|hp|kW|0}} in some models. Until [[fuel injection]] began to appear in the 1980s, net power ratings did not rise above {{cvt|210|hp|kW|0}}.

From the 1978 model year, the 302 became more commonly known as the 5.0&nbsp;Liter, although its metric displacement is only {{cvt|4942|cc|L CID|1}}. Despite Ford's branding, ''[[Car and Driver]]'' referred to the 302 as a 4.9-liter engine.{{when|date=May 2024}} Other terms for it included "5-Oh", "5-Point-Oh", and "5 Liter".

[[Throttle-body fuel injection]] became available on the 1980 [[Lincoln Continental]], and became standard on all non-H.O. 5.0&nbsp;Liter engines for 1983. For the 1986 model year, Ford replaced the throttle-body system with sequential multi-port fuel injection, identifiable by the large intake with an "EFI 5.0" badge on top.

Variants of the engine remained in use in Ford passenger cars and light trucks through the mid-1990s, and in SUVs until 2001.

{{hidden begin|title=Applications:|titlestyle=background:#99FF99; text-align:left;|bodystyle=text-align:left;}}
*1968–1970 [[Ford Fairlane (Americas)]]
*1968–1970 [[Ford Falcon (North America)]]
*1968–1995 [[Ford Mustang]]
*1968–1974 [[Ford Galaxie]]
*1968–1996 [[Ford Econoline]]
*1968–1986 [[Ford LTD (Americas)]]
*1969–1991 [[Ford Country Squire]]
*1969–1974 [[Ford Torino]]
*1969–1996 [[Ford F-Series]]
*1969–1996 [[Ford Bronco]]
*1971–1977 [[Ford Maverick]]
*1972–1979 [[Ford Ranchero]]
*1975–1980 [[Ford Granada (North America)]]
*1977–1981, 1983–1988, 1991–1993 [[Ford Thunderbird]]
*1977–1979 [[Ford LTD II]]
*1978–1979 [[Ford Fairmont]]
*1978–1991 [[Ford LTD Crown Victoria]]
*1996–2001 [[Ford Explorer]]
*1968, 1977–1981, 1983–1988, 1991–1993 [[Mercury Cougar]]
*1968–1969 [[Mercury Cyclone]]
*1968–1976 [[Mercury Montego]]
*1969–1991 [[Mercury Colony Park]]
*1969–1977 [[Mercury Comet]]
*1975–1980 [[Mercury Monarch]]
*1979–1986 [[Mercury Capri]]
*1979–1986 [[Mercury Marquis]]
*1983–1991 [[Mercury Grand Marquis]]
*1997–2001 [[Mercury Mountaineer]]
*1977–1980 [[Lincoln Versailles]]
*1980, 1982–1987 [[Lincoln Continental]]
*1980–1983 [[Lincoln Continental Mark VI|Continental Mark VI]]
*1984–1985 [[Lincoln Continental Mark VII|Continental Mark VII]]
*1986–1992 [[Lincoln Continental Mark VII|Lincoln Mark VII]]
*1981–1990 [[Lincoln Town Car]]
*1989–2003 [[Rayton-Fissore Magnum#Laforza|Laforza]]
{{hidden end}}

====GT-350====
For 1968 only, there were three versions of the engine. The standard powerplant was a 302-4V with a high-rise manifold (basic intake at first), a Holley four-barrel 600 CFM carburetor and a dual exhaust, producing {{cvt|250|hp|kW|0}} at 4,800&nbsp;rpm and {{cvt|310|lbft|Nm|0}} at 2,800&nbsp;rpm. An optional, factory installed, Paxton supercharger was available that increased the GT350's output to {{cvt|335|hp|kW|0}} at 5,200&nbsp;rpm and {{cvt|324|lbft|Nm|0}} at 3,200&nbsp;rpm.{{cn|date=January 2025}}. A special high-performance Shelby-modified version of the 302 was offered by Ford in the Shelby GT350 as a mid-year replacement during the model-year.<ref>{{cite web|url=http://thecarsource.com/shelby/1968/1968specs.shtml|title=1968 Shelby Cobra Mustang Specs on thecarsource.com|access-date=21 November 2016}}</ref> Key features included: an angled, high-rise aluminum or iron intake manifold, a larger [[Holley Performance Products|Holley]] four-barrel 715 CFM carburetor, and bigger valves of {{cvt|1.875|in|mm}} intake and {{cvt|1.6|in|mm}} exhaust. It had a longer-duration camshaft, still with hydraulic lifters. The heads had special close-tolerance pushrod holes to guide the pushrods without rail rocker arms or stamped steel guide plates. The combustion chambers also featured a smaller quench design for a higher compression ratio and enhanced flow characteristics. Additionally, high-flow cast exhaust manifolds similar to those on the 289 Hi-Po K-code engine further improved output. Heavy-duty connecting rods with high-strength bolts and a [[nodular iron]] crankshaft were also included in this package. Rated power (SAE gross) was estimated at {{cvt|315|hp|kW|0}} at 5,000&nbsp;rpm and {{cvt|333|lbft|Nm|0}} at 3,200&nbsp;rpm.{{cn|date=January 2025}}. The package, which cost $692 including some other equipment, was not popular and did not return for 1969. This engine is documented in the Ford factory engine repair manual for 1968 Mustangs and Fairlanes.{{cn|date=May 2024}}

===={{anchor|5.0}} 5.0 H.O.====
[[File:Mustang111.JPG|thumb|5.0 HO in a Ford Mustang]]
The 1982 model year brought a new 5.0 High Output variation of the 302. Mustangs and [[Mercury Capri]]s with manual transmissions were equipped with two-barrel carburetors in 1982, then got a four-barrel Holley carburetor for 1983–85. The block got revised, taller lifter bosses to accept roller lifters, and a steel camshaft in 1985. Electronic sequential fuel injection was introduced in 1986. While sequential injection was used on the Mustang beginning in 1986, other car and truck models continued to use a batch-fire fuel injection system. The speed-density based [[engine control unit|ECU-controlled]] electronic fuel-injection (EFI) systems used a large, two-piece, cast-aluminum manifold. It was fitted on all 302 engines through 1988, after which it was phased out for a [[mass flow sensor|mass airflow sensor]] (MAF) system in most applications. Non–California compliant [[Ford Panther platform|Panther platform]] cars kept the speed-density system until the Lincoln Town Car got the 4.6&nbsp;L OHC Modular V8 for model year 1991, and the [[Ford Crown Victoria|Crown Victoria]] and Mercury Grand Marquis for 1992.

The same manifold was used in MAF applications, with the addition of the MAF sensor in the air intake tube. The MAF system continued, with minor revisions, until the retirement of the engine in 2001. Ford offered a performance head that was a stock part on 1993–1995 Mustang Cobra models and pre-1997&nbsp;½ Ford Explorers and [[Mercury Mountaineer]]s equipped with the 5.0&nbsp;L engine called the GT40 head (casting ID F3ZE-AA). In mid-1997, the Explorer and Mountaineer 5.0&nbsp;L heads were revised and renamed GT40P. The GT40P heads, unlike the GT40 heads, had a very well-developed port shape which yielded about 200&nbsp;cfm on the intake side and 140&nbsp;cfm on the exhaust side without increasing the size of the ports from the standard E7TE castings, and without increasing the exhaust valve size. These highly-efficient heads also had smaller 59–61&nbsp;cc combustion chambers for added compression, and the combustion chamber shape was revised to put the spark plug tip near the center of the chamber for a more even burn.

Applications:
*1982–1995 [[Ford Mustang]]
*1982–1986 [[Mercury Capri]]
*1984–1985 [[Ford LTD (Americas)#LTD LX (1984–1985)|Ford LTD LX]]
*1984–1985 [[Ford Sierra]] XR8 (South Africa)<ref name=TAM85>{{Cite book | title = Quattroruote: Tutte le Auto del Mondo 1985 | editor = Mastrostefano, Raffaele | publisher = Editoriale Domus S.p.A | ref = TAM85 | date = 1985 | language = it | page = 434 | location = Milano | isbn = 88-7212-012-8}}</ref>
*1985 [[Mercury Marquis#Marquis LTS|Mercury Marquis LTS]]
*1987–1992 [[Lincoln Continental Mark VII|Lincoln Mark VII]] (1987 LSC models only)
*1991–1993 [[Ford Thunderbird]]
*1991–1993 [[Mercury Cougar]]
*1991–2002 [[Ford Falcon (Australia)|Ford Falcon]]
*1991–2002 [[Ford Fairlane (Australia)|Ford Fairlane/Ford LTD]]
*1996–2001 [[Ford Explorer]]
*1997–2001 [[Mercury Mountaineer]]
*1990–1996 [[Panoz Roadster]]

=====Marine 302=====
The 302 was [[marinized]] and offered in both standard and reverse-rotation setups.

====5.6====
In 2001, Ford Australia developed a {{convert|5605|cc|L cc cuin|order=out|adj=on|1}} small block by lengthening the stroke from {{cvt|3.0|in|mm|1|order=flip}} to {{cvt|86.4|mm|in|1}}.<ref>[[#AR02|Automobil Revue (2002)]], p. 288.</ref> The engine featured reworked large-valve GT40P heads, a unique eight-trumpet inlet manifold fitted with a unique throttle body, a long-throw crank, H-beam rods, and roller rockers. It produced {{cvt|335|hp|kW|0}} at 5,250&nbsp;rpm and {{cvt|369|lbft|Nm|0}} at 4,250&nbsp;rpm.<ref>{{cite web | url = http://www.fpv.com.au/theheritage/falcon/2001auiiite50andts50.aspx | title = 2001 AUIII TE50 and TS50 | archive-url = https://web.archive.org/web/20091001050421/http://www.fpv.com.au/theheritage/falcon/2001auiiite50andts50.aspx | archive-date = 2009-10-01 | work = FPV Heritage | publisher = Ford Australia}}</ref> The engine was used in special 2001–2002 "T" series Ford Falcons and XR8 Pursuit 250s, which were the last models developed in collaboration with [[Tickford Vehicle Engineering]], and which were exclusively available from dealers under the FTE (Ford Tickford Experience) banner.

===4-Bolt main bearing caps===
====GT40====
In response to a new Le Mans regulation limiting engine displacement to {{cvt|5|L|cuin|0}}, Ford added an extra 1/8-inch of piston travel to the 289 Hi-Performance V8, yielding the {{cvt|302|cuin|cc|0}} block. It featured heavy-duty four-bolt main bearing caps and pressed-in core plugs, and was topped with Gurney-Weslake aluminum heads.{{citation needed span|text=About 50 blocks were made.|This unsupported boldface claim needs a reliable citation.|date=May 2024}}

====Tunnel-Port 302====
The 302 "Tunnel-Port" engine was envisioned as the motor that would bring Ford a third Trans-Am Championship title in 1968.

Starting with a 1967 GT40 block, Ford fitted cylinder heads with a design based on their NASCAR 427 heads. The intake ports were straight, instead of snaking around the push rods, while the push rods went through the center of the ports (thus the name "Tunnel-Port"). This configuration also enabled larger valves to be used. The 302 tunnel-port motor was topped off with an aluminum dual quad intake.

Shelby [[dynamometer]] runs showed the engine was capable of producing {{cvt|440|–|450|hp|kW|0}}, and of operating in a very high rpm band (8000+).

====Boss 302====
[[File:Boss302Engine.jpg|thumb|[[Ford Boss 302 engine|Boss 302 engine]]]]
{{main|Ford Boss 302 engine}}

Officially called the "302&nbsp;H.O.", the Boss 302 was a performance variant of the small block designed to help Ford wrest back the 5-liter Trans-Am racing championship from the [[Camaro Z28|Camaro Z/28]]. Conceived of by chief engineer Bill Gay and realized by Bill Barr, it put large-port, large-valve, quench-chambered, free-flowing cylinder heads adapted from the design destined for the 351 Cleveland, which debuted in 1969,<ref>{{cite web |last1=Holdener |first1=Richard |title=Ford Boss 302 Engine Build - Build A Better Boss - Tech |url=https://www.motortrend.com/how-to/mdmp-1011-ford-boss-302-engine-build/ |website=MotorTrend |access-date=13 February 2023}}</ref> on a special racing block, bringing rated power to {{cvt|290|hp|kW|0}}. According to some reports, the canted-valve, deep-breathing, high-revving engine could produce more than {{cvt|310|hp|kW|0}}, although it was equipped with an electrical revolution limiter that restricted maximum engine speed to 6,150&nbsp;rpm. The 302&nbsp;H.O. borrowed both components and ideas from the 289 HiPo. A strong 4-bolt main bottom end, thicker cylinder walls, steel screw-in [[core plug]]s, aggressive forged-steel crank, special HD connecting rods, and Cleveland-style forged pistons were geared to racing. The [[Boss 302 Mustang]] was offered only for the 1969 and 1970 model years. In the January 2010 issue of ''Hot Rod'' magazine, a Boss 302 engine built to the exact specifications, settings, and conditions of the original engine was tested. It produced {{cvt|372|hp|kW|0}} at 6,800&nbsp;rpm (650&nbsp;rpm over the original engine's redline) and {{cvt|325|lbft|Nm|0}} of torque at 4,200&nbsp;rpm.<ref name="hrm-shootout">{{cite web |author=<!-- not stated --> |date=2009-11-30 |title=Muscle Car Engine Shootout - Chevy Vs. Ford Showdown |url=https://www.hotrod.com/how-to/hrdp-1001-muscle-car-engine-shootout |website=hotrod.com |location= |publisher= |access-date=}}</ref>

==351W==<!-- This section is linked from [[Ford Mustang]] -->
[[File:1969 Ford Mustang Mach 1 351 Windsor engine.JPG|thumb|A 351 Windsor V8 in a 1969 Ford Mustang]]

The 351W (Windsor) made its debut in 1969; it is often confused with the Ford 351 Cleveland, a different engine of nearly identical displacement that also began production in 1969. The {{cvt|5766|cc|cuin L cc|1|order=out}} Windsor featured a {{cvt|32.5|mm|1|order=flip}} taller deck height than the 289/302, allowing a stroke of {{cvt|3.5|in|mm|1}}. It was initially rated (SAE gross) at {{cvt|250|hp|kW|0}} with a two-barrel carburetor (referred to as "2V" in engine designations) or {{cvt|290|hp|kW|0}} with a four-barrel (designated "4V"). Emissions compliance led to a compression drop in 1971. When Ford switched to net power ratings in 1972 power ratings had fallen to {{cvt|153|HP|kW}} from {{cvt|161|hp|kW}}.

The 289, 302, and 351W all share the same bellhousing, motor mounts, and other small parts. The [[distributor]] is slightly different, to accommodate a larger [[oil pump (internal combustion engine)|oil pump]] shaft and larger oil pump. Some years had threaded dipstick tubes. The 351W had larger main bearing caps, thicker and longer connecting rods. The firing order was changed to 1-3-7-2-6-5-4-8 from the usual 1-5-4-2-6-3-7-8 to move the "noise" of the consecutively-firing adjacent front cylinders to the sturdier rear part of the engine block while reducing excessive main bearing load. The changes added some {{cvt|25|lb|kg|0}} to the engine's dry weight.

The head castings and valve head sizes from 1969 to 1976 were different, notably in passages for air injection and spark plug diameters (1969–1974 18&nbsp;mm, 1975 and up 14&nbsp;mm). From 1977 onward, the 351W shared the same head casting as the 302, differing only in bolt hole diameters (7/16&nbsp;inch for the 302, 1/2&nbsp;inch for the 351W). Early blocks (casting ID C9OE-6015-B) had enough metal on bearing saddles 2, 3, and 4 for four-bolt mains, and as with all small-block Fords, were superior in strength to most late-model, lightweight castings. Generally, the 1969 to 1974 blocks are considered to be stronger than the later blocks, making these early units some of the most desirable in the small block or 335-series. During the 1980s, a four-barrel version (intake manifold casting ID E6TE-9425-B) was reintroduced for use in light trucks and vans. In 1988, [[fuel injection]] replaced the four-barrel carburetor. Roller camshaft/lifters were introduced in 1994.

The original connecting rod beam ([[Forge|forging]] ID C9OE-A) featured drilled oil squirt bosses to lubricate the piston pin and cylinder bore and rectangular-head rod bolts mounted on broached shoulders. A number of [[Fatigue (material)|fatigue failures]] were attributed to the machining of the part, so the bolt head area was spot-faced to retain metal in the critical area, requiring the use of 'football head' bolts. In 1975, the beam forging (D6OE-AA) was updated with more metal in the bolt-head area. The oil squirt bosses were drilled for use in export engines, where the quality of accessible lubricants was questionable. The rod cap forging remained the same on both units (part ID C9OE-A). In 1982, the [[Ford Essex V6 engine (Canadian)|Essex V6 engine]] used a version of the 351W connecting rod (E2AE-A) machined in [[SI units|metric]] units, while the V8 part was machined with [[Society of Automotive Engineers|SAE]] units. The cap featured a longer boss for balancing than the original design.

In 1971 the block deck height was raised from {{cvt|9.480 to 9.503|in|mm}} (casting D1AE-6015-DA) to lower the compression ratio to reduce {{NOx|link=yes}} emissions without the need to change piston or cylinder-head design. In 1974, a boss was added on the front of the right cylinder bank to mount the [[secondary air injection#Pumped air injection|air injection pump]] (casting D4AE-A). In 1974, the oil dipstick tube moved from the timing case to the skirt under the left cylinder bank near the rear of the casting. In 1984, the rear main seal was changed from a two-piece to a one-piece design.

Around 8.6 million 351W engines were manufactured between 1969 and 1996 at the Windsor Engine Plant Number One.

Applications:
*1969–1974 [[Ford Galaxie]]
*1969–1970 [[Ford Mustang]]
*1969–1971 [[Mercury Cougar]]
*1969–1991 [[Ford Country Squire]]
*1969–1970 [[Ford Fairlane (Americas)]]
*1970–1976 [[Ford Torino]]
*1974–1976 [[Ford Elite]]
*1975–1976 [[Bricklin SV-1]]
*1975–1996 [[Ford E series]]
*1977–1979 [[Ford LTD II]]
*1977–1979 [[Ford Thunderbird]]
*1979–1996 [[Ford Bronco]]
*1979–1982 [[Ford LTD (Americas)]]
*1979–1991 [[Ford LTD Crown Victoria]] (after 1982, this engine would only be sold for police sales in the U.S.)
*1983–1997 [[Ford F-Series]]
*1977–1979 [[Mercury Cougar]] (station wagons only)
*1978, 1986–1991 [[Mercury Colony Park]]
*1978–1982 [[Mercury Marquis]]
*1986–1991 [[Mercury Grand Marquis]]
*1980 [[Lincoln Continental Mark VI|Continental Mark VI]]
*1995 [[Ford Mustang SVT Cobra#Cobra R (1995)|Ford Mustang SVT Cobra R]]

===Marine 351===
From the late 1960s through the early to mid-1990s, the 351 Windsor had a long history of being [[marinized]] by Holman Moody Marine, Redline of Lewiston, ID (now defunct), Pleasure Craft Marine (PCM), and Indmar for use in several makes of recreational boat, including; Correct Craft, Ski Supreme, [[Hydrodyne]], MasterCraft, and Supra inboard competition ski boats. The early marinized engines were rated at {{cvt|220|hp|kW|0}}. Most PCM and Indmar marinized 351s were rated at {{cvt|240|hp|kW|0}}. In the early 1990s, a {{cvt|260|hp|kW|0}} version and a high-output version that used GT40 heads and the Holley 4160 marine carburetor was rated at {{cvt|285|hp|kW|0}}. A few 351 GT40/HO engines were marinized equipped with throttle-body fuel injection (TBI) and were rated at {{cvt|310|hp|kW|0}}. The marine industry's relationship with the 351W platform ended when Ford was unable or unwilling to compete with GM's production of TBI- and MPI-equipped engines in mass quantity. During that time, the recreational marine community's small-block V8 platform of choice shifted to the {{cvt|350|cuin|L|1}} [[Chevrolet small-block engine (first- and second-generation)|Chevrolet L31 (Vortec 5700)]] engine series.

==Crate engines==
In the 2000s, [[Ford Racing]] Performance Parts sold two "Boss" [[crate engine]]s and at least one 351 block. Most Ford racing versions of the 302 and 351 feature a siamesed bore and many of them feature drilled coolant crossover holes.<ref>{{Cite web |last=Parts |first=Ford Performance |title=BOSS 302 engine block |url=https://performanceparts.ford.com/part/M-6010-BOSS302 |access-date=2023-04-12 |website=Ford Performance Parts}}</ref><ref>{{Cite web |last=Parts |first=Ford Performance |title=BOSS 302 engine block big bore |url=https://performanceparts.ford.com/part/M-6010-B302BB |access-date=2023-04-12 |website=Ford Performance Parts}}</ref><ref>{{Cite web |last=Parts |first=Ford Performance |title=BOSS 351 engine block 9.5" deck |url=https://performanceparts.ford.com/part/M-6010-BOSS35195 |access-date=2023-04-12 |website=Ford Performance Parts}}</ref><ref>{{Cite web |last=Parts |first=Ford Performance |title=BOSS 351 engine block 9.5 deck big bore |url=https://performanceparts.ford.com/part/M-6010-BOSS351BB |access-date=2023-04-12 |website=Ford Performance Parts}}</ref><ref>{{Cite web |last=Parts |first=Ford Performance |title=351 aluminum block 9.5-inch deck |url=https://performanceparts.ford.com/part/M-6010-Z351 |access-date=2023-04-12 |website=Ford Performance Parts}}</ref><ref>{{Cite web |last=Parts |first=Ford Performance |title=351 aluminum block 9.2-inch deck |url=https://performanceparts.ford.com/part/M-6010-Z35192 |access-date=2023-04-12 |website=Ford Performance Parts}}</ref>

===FR Boss 302===
An all-new Boss 302 engine was unveiled in the 2006 SEMA show.<ref>{{cite web |url=http://www.tuningnews.net/article/061031c/ford-racing-mustang-boss-302/ |title=Ford Racing brings the boss back with new line of BOSS 302 Crate Engines |publisher=Tuningnews.net |access-date=2010-07-15 |archive-date=2010-06-21 |archive-url=https://web.archive.org/web/20100621043539/http://www.tuningnews.net/article/061031c/ford-racing-mustang-boss-302/ |url-status=dead}}</ref>

===FR Boss 351W===
The "Racing Boss 351" (not to be confused with the Ford 335 engine Cleveland-based [[Ford 335 engine#1971 R-code (Boss 351)|Boss 351]]) is a crate engine based on the {{cvt|351|cuin|cc|0}} Ford Windsor engine, but with Cleveland-sized {{cvt|2.75|in|mm|0}} main bearing journals. Deck height choices include {{cvt|9.2|in|mm|0}} and {{cvt|9.5|in|mm|0}}. Maximum displacements are {{cvt|4.25|in|mm|0}} stroke and {{cvt|4.125|in|mm|0}} bore. The resulting maximum displacement is {{cvt|{{engine size|stroke=4.25|bore=4.125|cyl=8|rnd=2}}|cuin|cc|0}}.

The uncross-drilled block with increased bore capacity became available from the third quarter of 2009. A {{cvt|427|cuin|cc |0}} Boss 351-based crate engine producing {{cvt|535|hp|kW|0}} was available from the first quarter of 2010.

In 2010, the [[Suggested retail price|MSRP]] for the Boss 351 block was US$1,999.<ref>{{cite web |url=http://www.autoblog.com/2009/06/13/ford-racing-introduces-new-boss-351-engine-block/ |title=Ford Racing introduces new Boss 351 engine block |author=Korzeniewski, Jeremy |work=Autoblog |date=June 13, 2009}}</ref>

==See also==
* [[List of Ford engines]]

==Notes==
{{notelist}}

== References ==
{{Reflist|30em}}

==Further reading==
* {{Cite book | last1=Martin | first1=Isaac | year=1999 | title=Ford Windsor Small-Block Performance: Parts and Modifications for High Performance Street and Racing | pages=1–2 | edition=1st | publisher=Penguin Group, Inc. | isbn=1-55788-323-8 | ref=Martin1999}}
* {{cite book | editor-last=Nötzli | editor-first=Max | title=Automobil Revue 2002 | publisher=Büchler Grafino AG | location=Berne, Switzerland | language=de, fr | page=288 | volume=97 |date=7 March 2002 | isbn=3-905-386-02-X | ref=AR02}}
* {{Cite book | last1=Reid | first1=George | year=2001 | title=How to Build Max Performance Ford V-8S on a Budget | pages=[https://archive.org/details/howtobuildmaxper00reid/page/5 5–6] | publisher=Cartech, Inc. | isbn=1-884089-55-0 | ref=Reid2001 | url=https://archive.org/details/howtobuildmaxper00reid/page/5}}

==External links==
* [https://web.archive.org/web/20050518000641/http://www.fordclassics.com/enginespecs.html Short descriptions of Ford overhead valve V8 engines]

{{Ford early engine timeline}}
{{Ford engine timeline}}

{{DEFAULTSORT:Ford Windsor Engine}}
[[Category:Ford engines|Windsor]]
[[Category:V8 engines]]
[[Category:History of Windsor, Ontario]]
[[Category:Gasoline engines by model]]