Editing Geophone

{{Short description|Recording device in geology}}
{{about|the electronic seismic recording device|the percussion instrument|Geophone (musical instrument)}}
{{refimprove|date=December 2012}}
[[File:Geophone SM-24.jpg|thumb|upright|140px|Geophone (SM-24), frequency band 10 Hz to 240 Hz, standard resistance 375 Ω]]
A '''geophone''' is a device that converts ground movement (velocity) into [[voltage]], which may be recorded at a recording station. The [[Standard deviation|deviation]] of this measured voltage from the base line is called the [[seismic]] response and is analyzed for structure of the Earth.

==Etymology==
The term '''geophone''' derives from the Greek word "γῆ (ge)
" meaning "[[classical element|earth]]" and "phone" meaning "sound".

==Construction==
[[File:GeoPhone.JPG|thumb|upright|Geosource Inc. MD-79—8 Hz, 335 Ω geophone]]
Geophones have historically been passive [[analog circuit|analog]] devices and typically comprise a spring-mounted wire coil moving within the field of a case-mounted permanent magnet to generate an electrical signal.<ref name="Geophones and Accelerometers">{{cite book | title=An Introduction to Applied and Environmental Geophysics-second edition | publisher=WILEY BLACKWELL | author=John M Reynolds | year=2011 | pages=170 | isbn=978-0-471-48535-3}}</ref> Recent designs have been based on [[microelectromechanical systems]] (MEMS) technology which generates an electrical response to [[ground motion]] through an active [[feedback]] circuit to maintain the position of a small piece of silicon.

The response of a coil/magnet geophone is proportional to ground velocity, while MEMS devices usually respond proportional to
[[peak ground acceleration|acceleration]]. MEMS have a much higher noise level (50&nbsp;dB velocity higher) than geophones and can only be used in strong motion or active seismic applications.
==Frequency response==
The [[frequency response]] of a geophone is that of a [[harmonic oscillator]], fully determined by corner frequency (typically around 10&nbsp;Hz) and damping (typically 0.707). Since the corner frequency is proportional to the inverse square root of the moving mass, geophones with low corner frequencies (< 1&nbsp;Hz) become impractical. It is possible to lower the corner frequency electronically, at the price of higher noise and cost.

Although waves passing through the Earth have a three-dimensional nature, geophones are normally constrained to respond to single dimension - usually the vertical. However, some applications require the full wave to be used and three-component or 3-C geophones are used.  In analog devices, three moving coil elements are mounted in an [[orthogonal]] arrangement within a single case.

== Distinction from seismometers ==
Geophones are similar to [[Seismometer|seismometers]] in their design and are also used to register [[Seismic wave|seismic waves]]. In the past, there were clear differences between geophones and seismometers. Compared to conventional geophones, seismometers are more suitable for detecting extremely small ground movements as they cover a wider frequency band, including the frequency range below their [[natural frequency]], usually from 0.01 to 50 Hz.<ref name=":0">{{Cite journal |last=Hou |first=Yue |last2=Jiao |first2=Rui |last3=Yu |first3=Hongyu |date=February 2021 |title=MEMS based geophones and seismometers |url=https://linkinghub.elsevier.com/retrieve/pii/S0924424720318136 |journal=Sensors and Actuators A: Physical |language=en |volume=318 |pages=112498 |doi=10.1016/j.sna.2020.112498|url-access=subscription }}</ref> In conventional geophones, the frequency band is in the range of 1-15 Hz. They are cheaper than seismometers and are therefore more commonly used in arrays for large area detection with better specialised resolution.<ref name=":0" /> However, with the development of new technologies, the frequency coverage in compact devices has also increased significantly, so that geophones can now cover frequency bands from 0 to 500 Hz and the boundaries between geophones and seismometers are becoming blurred.<ref name=":0" />
==Uses==
[[File:Man using a geophone.jpg|thumb|left|upright|Man using a geophone]][[File:Single End Spread & Split Stread.jpg|thumb|Single End Spread<ref>{{cite web|url=http://wiki.seg.org/wiki/Dictionary:Single-ended_spread|title=Dictionary:Single-ended spread - SEG Wiki|website=wiki.seg.org|access-date=21 July 2017}}</ref> & Split Stread<ref>{{cite web|url=http://wiki.seg.org/wiki/Dictionary:Split_spread|title=Dictionary:Split spread - SEG Wiki|website=wiki.seg.org|access-date=21 July 2017}}</ref>]]
[[File:Source Receivers single fold-3 Fold.jpg|thumb|Source Receivers single fold-3 Fold]]
[[File:Royal Rumble.jpg|thumb|Royal Rumble<ref>{{cite web|url=http://wiki.seg.org/wiki/Dictionary:Royal-rumble|title=Dictionary:Royal-rumble - SEG Wiki|website=wiki.seg.org|access-date=21 July 2017}}</ref>]]
The majority of geophones are used in [[reflection seismology]] to record the energy waves reflected by the subsurface geology. In this case the primary interest is in the vertical motion of the Earth's surface. However, not all the waves are upwards traveling.  A strong, horizontally transmitted wave known as ground-roll also generates vertical motion that can obliterate the weaker vertical signals.  By using large areal arrays tuned to the wavelength of the ground-roll the dominant noise signals can be attenuated and the weaker data signals reinforced.

Analog geophones are very sensitive devices which can respond to very distant tremors. These small signals can be drowned by larger signals from local sources. It is possible though to recover the small signals caused by large but distant events by correlating signals from several geophones deployed in an array. Signals which are registered only at one or few geophones can be attributed to unwanted, local events and thus discarded. It can be assumed that small signals that register uniformly at all geophones in an array can be attributed to a distant and therefore significant event.

The sensitivity of passive geophones is typically 30 volts per (meter per second), so they are in general not a replacement for 
[[Seismometers|broadband seismometers]].{{clarify|how does this follow?|date=June 2020}}

Conversely, some applications of geophones are interested only in very local events. A notable example is in the application of remote ground sensors (RGS) incorporated in [[Unattended ground sensors|unattended ground sensor]] (UGS) systems. In such an application there is an area of interest which when penetrated a system operator is to be informed, perhaps by an alert which could be accompanied by supporting photographic data.

Geophones were used on the Moon for a number of active and passive experiments as part of the [[Apollo Lunar Surface Experiments Package]].

== See also ==
* [[Accelerometer]]
* [[Hydrophone]]
* [[Michelson interferometer]]
* [[Seismometer]]

==References==
{{reflist}}

==External links==
{{Commons category|Geophones}}
* [http://www.prc68.com/I/PSR1.shtml PSR-1 Seismic Intrusion Detector] (Vietnam era military device)


[[Category:Seismology instruments]]