Editing Pad Abort Test 2

{{Infobox spaceflight<!--technically not a spaceflight, but template seems best fit for this article-->
| name                  = Pad Abort Test 2
| image                 = Apollo Pad Abort Test -2.jpg
| image_caption         = Apollo LES Pad Abort Test (NASA)
| insignia              = Apollo program.svg

| mission_type          = Abort test
| operator              = [[NASA]]
| mission_duration      = 1&nbsp;minute, 52.6&nbsp;seconds
| distance_travelled    = {{convert|2.32|km|mi|sp=us}}
| suborbital_apogee     = {{convert|2.82|km|mi|sp=us}}

| spacecraft            = [[Apollo (spacecraft)|Apollo]] BP-23A
| manufacturer          = 
| launch_mass           = 
| landing_mass          =

| launch_date           = {{start-date|June 29, 1965, 13:00:01|timezone=yes}}&nbsp;UTC
| launch_rocket         = [[Apollo (spacecraft)#Launch escape system (LES)|Apollo LES]]
| launch_site           = [[White Sands Missile Range|White Sands]] [[White Sands Launch Complex 36|LC-36]]

| landing_date          = {{end-date|June 29, 1965, 13:01:54|timezone=yes}}&nbsp;UTC
| landing_site          =

| previous_mission      = [[A-003]]
| next_mission          = [[A-004]]
| programme             = [[Apollo program|Project Apollo]]<br/><small>Abort tests</small> 
}}
'''Pad Abort Test 2''' was the follow-on second [[pad abort test|abort test]] to [[Pad Abort Test 1]] of the [[Apollo spacecraft]] .

==Objectives==
Apollo Pad Abort Test 2 was the fifth of six uncrewed Apollo missions that flight tested the capability of the [[Apollo spacecraft#Launch escape system (LES)|launch escape system]] (LES) to provide for safe recovery of Apollo crews under critical abort conditions. This flight was the second test of the launch escape system with the abort initiated from the launch pad.

The launch escape system included qualified launch escape and pitch motors and was equipped with canards to orient the vehicle aft heat shield forward prior to tower jettison and parachute deployment. A boost protective cover was also provided. The spacecraft was BP-23A, a [[Boilerplate (spaceflight)|boilerplate]] [[Apollo command module]] that had been used on mission [[A-002]] and refurbished to more nearly simulate a Block-I-type command module in mass and other characteristics. The Earth landing system was similar to the one used in mission [[A-003]].

==Flight==

The test flight was conducted on June 29, 1965. The vehicle was lifted from Launch Complex 36 by the launch escape motor at 13:00:01 UTC (06:00:01 MST). The launch escape and pitch control motors ignited simultaneously, placing the test vehicle into the planned initial trajectory. A moderate roll rate developed at lift-off, which was due to the aerodynamic asymmetry of the vehicle configuration; however, the roll rate did not affect the success of the test.

The [[Canard (aeronautics)|canard surfaces]] deployed and turned the vehicle to the desired orientation for drogue parachute deployment. During the turnaround maneuver, the launch escape tower and forward heat shield were jettisoned as planned. The boost protective cover, which was attached to the launch escape system, protected the conical surface of the command module and remained intact through a canard-induced pitch maneuver. At tower jettison, the soft boost protective cover, as expected, collapsed because of differential pressure during removal from the command module. No recontact or interference between the major components was evident during tower jettison and parachute deployment.

Although one of the pilot parachute steel cable risers was kinked, the Earth landing system functioned properly. The drogue parachutes inflated and stabilized the command module for pilot and main parachute deployment, and the rate of descent while on the main parachutes was satisfactory. The maximum altitude achieved was {{convert|9258|ft|m}} above mean sea level, approximately {{convert|650|ft|m}} higher than predicted. The command module landed about {{convert|7600|ft|m}} from the launch site, some {{convert|2000|ft|m}} farther than planned.

Four glass samples had been mounted on the command module in the general area planned for the rendezvous and crew windows. No soot appeared on the samples, but an oily film was found on the exposed surfaces of three of the four samples. This film, however, was not expected to cause excessive degradation to the horizon scan or ground orientation ability during an abort. The test was highly successful and all planned objectives were fulfilled.

==External links==
*[http://www.hq.nasa.gov/office/pao/History/SP-4009/cover.htm The Apollo Spacecraft: A Chronology] {{Webarchive|url=https://web.archive.org/web/20171209084600/http://www.hq.nasa.gov/office/pao/History/SP-4009/cover.htm |date=2017-12-09 }}
*[https://history.nasa.gov/apsr/apsr.htm Apollo Program Summary Report]
*[https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/19790076633_1979076633.pdf Flight Test Report Apollo Mission Pad Abort 2 - September 1965 (PDF)]

{{Include-NASA}}

{{Apollo program| before=[[A-104]]| after=[[A-105]]}}

{{Use American English|date=January 2014}}

[[Category:Apollo program]]
[[Category:1965 in the United States]]
[[Category:1965 in spaceflight]]
[[Category:Test spaceflights]]
[[Category:Flight abort]]