Editing Working fluid

{{Short description|Pressurized gas or liquid in a heat engine}}
{{Refimprove|date=May 2010}}

For [[fluid power]], a '''working fluid''' is a [[gas]] or [[liquid]] that primarily transfers [[force]], [[motion]], or [[mechanical energy]]. In [[hydraulics]], [[water]] or [[hydraulic fluid]] transfers force between hydraulic components such as [[hydraulic pump]]s, [[hydraulic cylinder]]s, and [[hydraulic motor]]s that are assembled into [[hydraulic machinery]], [[hydraulic drive system]]s, etc. In [[pneumatics]], the working fluid is [[air]] or another gas which transfers force between pneumatic components such as [[compressor]]s, [[vacuum pump]]s, [[pneumatic cylinder]]s, and [[pneumatic motor]]s. In pneumatic systems, the working gas also [[energy storage|stores energy]] because it is compressible. (Gases also heat up as they are compressed and cool as they expand. Some gases also condense into liquids as they are compressed and boil as pressure is reduced.)

For passive [[heat transfer]], a '''working fluid''' is a gas or liquid, usually called a [[coolant]] or heat transfer fluid, that primarily transfers [[heat]] into or out of a region of interest by [[conduction (heat)|conduction]], [[convection]], and/or [[forced convection]] (pumped [[liquid cooling]], [[air cooling]], etc.).

The '''working fluid''' of a [[heat engine]] or [[heat pump]] is a gas or liquid, usually called a [[refrigerant]], coolant, or working gas, that primarily converts [[thermal energy]] (temperature change) into mechanical energy (or vice versa) by [[phase transition|phase change]] and/or [[heat of compression]] and expansion. Examples using phase change include water↔steam in [[steam engine]]s, and [[refrigerant]]s in [[vapor-compression refrigeration]] and [[air conditioning]] systems. Examples without phase change include air or hydrogen in [[hot air engine]]s such as the [[Stirling engine]], air or gases in [[heat pump and refrigeration cycle#Gas cycle|gas-cycle heat pumps]], etc. (Some heat pumps and heat engines use "working solids", such as rubber bands, for [[refrigeration#Elastocaloric refrigeration|elastocaloric refrigeration]] or thermoelastic cooling and [[nickel titanium]] in a prototype heat engine.)

Working fluids other than air or water are necessarily recirculated in a loop. Some hydraulic and passive heat-transfer systems are open to the water supply and/or atmosphere, sometimes through breather [[air filter|filters]]. Heat engines, heat pumps, and systems using volatile liquids or special gases are usually sealed behind [[relief valve]]s.

==Properties and states==
{{Textbook|section|date=May 2010}}
The [[working fluid selection|working fluid's properties]] are essential for the full description of thermodynamic systems. Although working fluids have many physical properties which can be defined, the thermodynamic properties which are often required in engineering design and analysis are few. [[Pressure]], [[temperature]], [[enthalpy]], [[entropy]], [[specific volume]], and [[internal energy]] are the most common.

[[File:Property diagram.JPG|frame|right|Pressure–volume diagram showing state (p,V)]]

If at least two thermodynamic properties are known, the state of the working fluid can be defined. This is usually done on a property diagram which is simply a plot of one property versus another.

[[File:therm process.JPG|frame|left|Typical thermodynamic process for a working fluid (expansion from state 1 to state 2)]]

When the working fluid passes through engineering components such as [[turbine]]s and [[compressor]]s, the point on a property diagram moves due to the possible changes of certain properties. In theory therefore it is possible to draw a line/curve which fully describes the thermodynamic properties of the fluid. In reality however this can only be done if the process is [[reversible process (thermodynamics)|reversible]]. If not, the changes in property are represented as a dotted line on a property diagram. This issue does not really affect thermodynamic analysis since in most cases it is the end states of a process which are sought after.

{{Clear}}
==Work==
The working fluid can be used to output useful [[work (physics)|work]] if used in a [[turbine]]. Also, in thermodynamic cycles energy may be input to the working fluid by means of a [[compression (physical)|compressor]]. The mathematical formulation for this may be quite simple if we consider a cylinder in which a working fluid resides. A piston is used to input useful work to the fluid. From mechanics, the work done from state 1 to state 2 of the process is given by:
:<math> W = -\int_{1}^{2} \mathbf{F} \cdot \mathrm{d}\mathbf{s}</math>

where ''ds'' is the incremental distance from one state to the next and ''F'' is the force applied. The negative sign is introduced since in this case a decrease in volume is being considered. The situation is shown in the following figure:

[[File:Piston cylinder.jpg|frame|none|Work input on a working fluid by means of a cylinder–piston arrangement]]

The force is given by the product of the pressure in the cylinder and its cross sectional area such that
:<math>\begin{align}
W &= -\int_{1}^{2} PA \cdot \mathrm{d}\mathbf{s} \\
&= -\int_{1}^{2} P \cdot \mathrm{d}V
\end{align}</math>

Where ''A&sdot;ds = dV'' is the elemental change of cylinder volume. If from state 1 to 2 the volume increases then the working fluid actually does work on its surroundings and this is commonly denoted by a negative work. If the volume decreases the work is positive. By the definition given with the above integral the work done is represented by the area under a [[pressure–volume diagram]]. If we consider the case where we have a constant pressure process then the work is simply given by
:<math>\begin{align}
W &= -P \int_{1}^{2} \mathrm{d}V \\
&= -P \cdot \left(V_2 - V_1\right)
\end{align}</math>

[[File:Isobaric-process.svg|thumb|none|Constant pressure process on a p–V diagram]]

==Selection==
{{Main|Working fluid selection}}
Depending on the application, various types of working fluids are used. In a thermodynamic cycle it may be the case that the working fluid changes state from gas to liquid or vice versa. Certain gases such as helium can be treated as [[ideal gas]]es. This is not generally the case for superheated steam and the [[ideal gas equation]] does not really hold. At much higher temperatures however it still yields relatively accurate results. The physical and chemical properties of the working fluid are extremely important when designing thermodynamic systems. For instance, in a refrigeration unit, the working fluid is called the refrigerant. [[Ammonia]] is a typical refrigerant and may be used as the primary working fluid. Compared with water (which can also be used as a refrigerant), ammonia makes use of relatively high pressures requiring more robust and expensive equipment.

In air standard cycles as in [[gas turbine]] cycles, the working fluid is air. In the open cycle gas turbine, air enters a compressor where its pressure is increased. The compressor therefore inputs work to the working fluid (positive work). The fluid is then transferred to a combustion chamber where this time heat energy is input by means of the burning of a fuel. The air then expands in a turbine thus doing work against the surroundings (negative work).

Different working fluids have different properties and in choosing one in particular the designer must identify the major requirements. In refrigeration units, high latent heats are required to provide large refrigeration capacities.

==Applications and examples==
The following table gives typical applications of working fluids and examples for each:

{| class="wikitable" border="1"
|-
! Application
! Typical working fluid
! Specific example
|-
| [[Gas turbine]] cycles
| Air
|
|-
| [[Rankine cycle]]s
| [[Water]]↔[[steam]], [[pentane]], [[toluene]]
|
|-
| [[Vapor-compression refrigeration]], [[heat pump]]s
| [[Chlorofluorocarbon]]s, [[hydrochlorofluorocarbon]]s, [[fluorocarbon]]s, [[propane]], [[butane]], [[isobutane]], [[ammonia]], [[sulfur dioxide]]
| [[Refrigerator#Electric refrigerators|Commercial refrigerators]], [[air conditioning#Construction|Air conditioners]]
|-
| [[Reusable launch vehicle]] extensible [[VTVL|vertical]]-[[launch vehicle landing gear|landing legs]]
| [[Helium]]<ref name=musk20130502>
{{cite news |last=Lindsey|first=Clark |title=SpaceX shows a leg for the "F-niner" |url=http://www.newspacewatch.com/articles/spacex-shows-a-leg-for-the-quotf-ninerquot.html |date=2013-05-02 |access-date=2013-05-02 |quote=''F9R (pronounced F-niner) shows a little leg. Design is a nested, telescoping piston w A frame... High pressure helium. Needs to be ultra light.'' |url-access=subscription}}</ref>
| [[SpaceX reusable launch system development program]]
|}

==See also==
*[[List of gases]]
*[[Water power engine]]

==References==
{{Reflist}}
*{{cite book |title=Applied Thermodynamics for Engineering Technologists|last=Eastop & McConkey |year=1993 |edition=5th |publisher=Prentice Hall |location=Singapore |isbn=0-582-09193-4 |pages=9–12}}

{{Steam engine configurations|state=collapsed}}
[[Category:Engines]]
[[Category:Fluid mechanics]]
[[Category:Thermodynamics]]