Incubator escapee wiki

Citroën XM

Article Discussion

Template:Use dmy dates Template:Infobox automobile The Citroën XM is an executive car manufactured and marketed by Citroën from 1989 to 2000. Voted 1990 European Car of the Year for its contributions in terms of design and technological innovation, it was the first production automobile in the world to be equipped with electronically controlled hydropneumatic suspension.<ref>Template:Cite news</ref>

With a minor facelift in 1994, XM production reached 333,405 over the course of 11 years.<ref name=HaxoV6>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

HistoryEdit

Launched on 23 May 1989,<ref>Template:Cite news</ref> the XM was the company's flagship saloon, replacing the Citroën CX. It went on sale in its native France immediately afterwards, and was available in right-hand drive on the UK market from October 1989. The CX Break and Familiale remained in production until the spring of 1991, when the XM Estate launched.

The XM did not enjoy the commercial success of its predecessors, the CX and the DS, which each raised the bar of automotive performance for other manufacturers.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> By the second half of the 1990s, sales were in sharp decline, and Citroën ended production in 2000. Total sales of the XM reached 333,405 in 11 years, of which 31,035 were of the Heuliez-built Breaks (estates).<ref name=HaxoV6/> The XM's replacement, the Citroën C6, was launched at the end of 2005.

In 2021, the company ceded use of the name to BMW for their BMW XM SUV.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Design advancesEdit

The XM offered active electronic management of its suspension; a partially galvanised body shell and the option of a 3.0 L V6 engine –  the first V6 in a Citroën since the Maserati-engined SM ended production in the mid 1970s.

The XM offered improved ventilation and rear accommodation, in width, legroom and height. In particular the rear passengers were seated higher than those in the front in order to afford a good view.<ref>The Daily Express World Car Guide 1998, page 30</ref> To improve rear seat comfort when the hatch was opened, the car had an additional, interior rear window – a feature not picked up by anyone else since. The XM shared a floorpan with the Peugeot 605, and the two models fared similarly in both teething problems and market acceptance.<ref name=TV0691.12>Template:Cite magazine</ref>

CompetitionEdit

The XM was intended to compete against prestige vehicles like the Mercedes-Benz W124, Audi 100 and BMW's 5 Series in a sector that accounted for 14.2% of the European market. It also competed with cars from mainstream brands including the Ford Scorpio and Opel Omega. Citroën was quoted as saying that the car was supposed to "take what Citroën means and make it acceptable".<ref name="autocar38">Autocar, 24 May 1989, page 38.</ref> The car's initial reception was positive. Some six months after its launch, the XM won the prestigious European Car of the Year award for 1990 (gaining almost twice as many votes as the second, the Mercedes-Benz SL)<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> and went on to win a further 14 major awards within a year of its launch.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

The anticipated annual sales of 450 cars a day in the first full year of production, or 160,000 units a year, never materialized.<ref>Car Styling, July 1989, page 7.</ref> Sales never reached this ambitious level (higher than even its popular predecessor) for a variety of reasons. Like the CX, the XM did not have the worldwide distribution of competitors from BMW, Audi, and Mercedes-Benz. Also, it was launched only a year before a major global recession began, impacting negatively on car sales across the world; a notable example being the UK, where more than 2.3 million new cars were registered in 1989, but that figure fell to less than 1.6 million in 1991 (a drop of more than 30% in just two years). In Japan the XM was sold through Mazda's Eunos dealership chain, part of an effort to minimize the appearance of Japan's automobile market being closed to imports.<ref name=DaiRede>Template:Citation</ref> It was also offered by Citroën's traditional importer Seibu Motor, who kept selling the XM by themselves after the Eunos brand was discontinued in 1996.

The market for executive cars made by volume manufacturers (Ford, Opel, etc.) was on the verge of decline as customers opted for offerings from more prestigious marques, a trend which saw Ford pull out of this market sector in 1998 and Opel/Vauxhall in 2003. Customers were placing a higher priority on speed and handling rather than ride comfort which was Citroën's specialty. The XM was underdeveloped at launch which resulted in reliability problems; the vehicle as designed was inconsistent in its abilities. The XM's styling was also controversial and alienated those who desired a more conventional three box sedan. The XM's sister car, the Peugeot 605, also proved a weak seller. Most subjective of all was the matter of the XM not living up to the expectations created by its forerunner the Citroën DS, despite that car having been launched in an era of national markets, of different demands and standards, an era when there was more scope for large advances in engineering and design than were possible in 1989.

Export markets experienced lower sales from the outset, partly due to the XM's pricing. The least expensive XM was nearly 50% more expensive at the time of launch than the corresponding CX. Whilst strong at first<ref>Template:Cite news</ref> home market sales also declined, after the mechanical issues of the first few model years became known.

By early 1993, the XM was viewed as an "underachiever".<ref name="Autocar, 24 Feb, page 54">[Autocar, 24 Feb, page 54].</ref> Initial sales in the UK were at 3,500 units a year, making it Citroën's weakest seller. The 2.0-litre petrol engined variants were viewed as being the least competitive. As a result, Citroën restructured the range such that all but the base model petrols were fitted with low-inertia Garret turbochargers to add an extra Template:Convert. This made the cars more powerful than more expensive competitors such as the Rover 820, Vauxhall Carlton and Ford Granada 2.0 GLX.<ref name="Autocar, 24 Feb, page 54"/>

After a run of 11 years, production finally ended in June 2000. By 1998, Citroën had confirmed that it would soon be discontinuing the XM and replacing it with an all-new model. At the Geneva Motor Show in March 1999, it unveiled the C6 Lignage concept car, which was scheduled for launch in 2001. In the event, the XM's successor - the Citroën C6 - did not go on sale until late 2005 and was even less successful.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Resale valueEdit

XM suffered from poor resale value, which affected sales of new cars.

Quentin Willson predicted in 1990 that the XM's residuals would be better than the outgoing CX<ref>"Old Top Gear 1991 – Citroën XM and Audi 100 estates (Bad Quality)". YouTube. https://www.youtube.com/watch?v=6kx0v5UDjbw. Retrieved 17 December 2011</ref> by the end of the car's life, its resale value was far below average, further denting the car's appeal.<ref name="CAR Magazine, September 2000">CAR Magazine, September 2000</ref>

By the mid-1990s, it was apparent that the XM's image meant it was less desirable than German products such as the BMW 5 Series.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The view of the XM as commercially unsuccessful is reported by Compucars,<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> the used car website, along with numerous other period commentaries.

FaceliftEdit

In mid-1994, the XM received a minor facelift<ref name="Car, May 1995 p94-104">Car, May 1995 p94-104</ref> with revisions including a driver's airbag (ending the single-spoke steering wheel), belt-pretensioners, a redesigned dashboard and upper door casings. The suspension was redesigned to reduce roll, pitch and dive and the design incorporated a passive rear-steering system similar to that on the Citroën Xantia. Power from the turbocharged engines increased to Template:Cvt from Template:Cvt at 4400 rpm.

In the United Kingdom, demand slowed significantly by the late 1990s.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

StylingEdit

The angular Bertone design was a development of Marcello Gandini's Citroën BX concept. Citroën's design chief, Art Blakeslee, believed "the XM is a modern and dynamic shape, with unique styling elements such as the very long, low hood, the extensive use of glass and the kick-up in the belt line". Another Citroën designer, Daniel Abramson, explained: "We lowered the belt line to give the shape a stronger image. It is purely a 'design statement' that is not functional and does nothing for the aerodynamics of the vehicle. We wanted a car that looks good from every angle". Abramson is also reported as saying that they "picked three areas to emphasise: 1) A very aggressive look ("Almost sinister"), 2) Lots of glass to create a greenhouse effect, and 3) An aerodynamic accent based on fact (low drag).<ref>Template:Citation</ref>

In 2013 Car<ref>Bird, G. (2013) "Bertone at 100" Car, April 2013, page 115.</ref> magazine described the XM as one of Bertone's seven most significant designs.

The standard 5-door models were called "Berline". The XM was also available as a "Break" (station wagon) – and in France, Tissier continued a tradition begun with the DS and CX, converting many to be used as ambulances and specialised delivery vehicles including their distinctive twin rear-axle conversions.

When introduced, lower-end and upper-end models looked largely identical. The main difference was in wheel design, while the most expensive models also received colour-coded rear view mirrors.<ref name=TV0691.12/>

  • Citroën XM Turbo D 12 1990 Olza - Spain.jpg

    Hatchback (pre-facelift)

  • 1993 Citroën XM hatchback (28813043511).jpg

    Hatchback (rear)

  • Citroen XM Break (1991-1994) II.jpg

    Break (pre-facelift)

  • 1992 Citroen XM L Estate.jpg

    Break (pre-facelift)

Second seriesEdit

Although not an official variant XMs produced around 1992/1993 have been termed series 1.5 cars due to the mix of newer technology (developed for the series 2) with the series 1 vehicle type. One example of this being the alterations to the "Hydractive" suspension system on such cars. Early vehicles (series 1) had a system that could be switched from 'Comfort' to 'Sport' mode, this did exactly what you would expect and firmed up the suspension on flicking the switch but this made for a harsh ride which Citroën owners don't like. So Citroën developed "Hydractive 2" suspension (for series 2 vehicles) that although in essence was the same it worked differently, it still had to two states 'hard' and 'soft' but the switching was controlled differently. In general smooth gentle driving the suspension would be in 'soft' mode ("Normal" mode according to Citroën on series 2 vehicles) which utilized all 6 suspension spheres and allowed 'crossflow' of fluid from side to side producing the characteristic wafting ride, but as soon as the suspension ECU sensed a large or sudden change in one of the sensors it would put the suspension into 'hard' mode locking out the extra centre spheres and stopping the 'crossflow' of fluid, this dramatically firmed up the suspension and cut body roll, as soon as the vehicle stabilized the ECU would switch the suspension system back into 'soft' mode. This is the basis of "Hydractive 2", a soft cosseting ride all the time unless the conditions demand otherwise, switching a "Hydractive 2" vehicle into "Sport" mode doesn't just switch out the extra spheres as with "Hydractive 1", it simply just narrows the parameters that cause the suspension to go into 'hard' mode and keeps the suspension in that mode for longer before defaulting back to 'soft' mode. So a series 1.5 vehicle has the styling of a series 1 but with some of the suspension refinements of the series 2 vehicles. There are other detail changes to the actual implementation of the "Hydractive" but unless you are maintaining the vehicle yourself these are unimportant.

There are a number of visible differences between the first series (May 1989 – May 1994) and second series (June 1994 – June 2000) cars, including:

  • In second generation XMs, the Citroën double-chevron logo was moved to the centre of the grille and became larger. It was located off-centre in the first generation cars.
  • The "XM" badge on the rear had a more stylised font (like that on the Xantia) and it was moved to the right of the tailgate.
  • The second generation cars were fitted with a lower rear spoiler on the tailgate, sitting much closer to the top of the boot.
  • The grey/black panel between the leading edge of the windscreen and the rear edge of the bonnet was colour-coded with the body colour. The original colouring was designed to echo the upward kick in the window line behind the rear door. With body coloured plastic this visual relationship became less clear and the "visual mass" of the front of the car increased somewhat. This effect was clearer on light coloured cars where the contrast between the dark areas and light areas was more pronounced.
  • The door mirrors were modified to improve the view of the passenger side mirror from the driver's seat. Previously it was slightly obscured by the A-pillar. However, the obscuration only affected the field of view above the road horizon which is relatively less important.

Differences to the interior include:

  • A more conventional four-spoke steering wheel including an integrated airbag. The driver airbag was standard on most models and countries, regardless of hand-drive configuration. As a result, the second generation models never had Citroën's distinctive single-spoke wheel. In certain markets (mainly the UK) and for certain models, XMs of the first generation were fitted with a two-spoke wheel after mid-1992.
  • A modified instrument panel, to accommodate an optional passenger airbag (standard after December 1995). Also, in 1997, front seat-mounted side airbags were added, which were optional or standard depending on model and market. The design was similar to the Xantia's dashboard.
  • The quality of the interior materials was marginally improved, with the leather and the seating being both softer but more supportive.
  • The upper part of door trim were redesigned to soften the shape. Series 1 cars had a pronounced chamfer-effect in keeping with the angular theme of the dashboard.
  • The driver and all passengers comfort was further enhanced (on Exclusive models) by variable heat seating, rather than as before just "on or off", with a dial switch allowing a heat setting of 1, 2, or 3.

Other major improvements include:

  • Better, more reliable electrics and a faster computer system controlling the new Hydractive 2 suspension.
  • Some models also received the "Auto Adaptive" gearbox, which supposedly assesses the driver's driving style, then switches to the most appropriate of approximately six onboard programmes. This gearbox was further enhanced by a "Sport" mode button (in addition to the sports button for the suspension), which shortened the gear change times, therefore offering a more responsive experience. The final new upgrade affecting the driving experience saw the introduction of a "Snow Mode" button, located next to the new sport mode button. Although rarely used in some countries, this was a surprisingly effective addition to the driver's arsenal; during any notable falls of snow that may affect the road ahead, a simple push of this button commands the gearbox to only accelerate from 2nd gear and up, and not to rev the engine too high, thus preventing any loss of traction.

In addition, the following changes were made to make the car easier to accept by more mainstream car buyers:

  • As a direct consequence of their high pressure hydraulics, early XM brake pedals had very little, if any, travel. Phase 2 XMs had some sponginess deliberately built into the braking system (by inserting a sleeved spring into the pedal linkage) to make their brakes feel more like those on other cars.
  • The Phase 2 "Hydractive 2" cars no longer "settled" down to the bottom of their suspension travel after having been parked for a while; this feature was termed "Anti-Sink" by Citroën. Such systems have even more complex hydraulics than 'Sinkers' because of the use of isolating valves and an extra sphere near the rear 'axle'. The hydraulic systems were also a lot quieter when maneuvering; this was due to the changes the "Anti-Sink" system brought. Early cars, 'sinkers', had a single output hydraulic pump which had its output divided into separate circuits, one for the power steering and one for the suspension/brake circuits (power steering needs a large flow rate whereas the suspension/brakes doesn't). The device which does this job is called a FDV (Flow Diverter Value), and this device hisses noticeably when the car is standing still or maneuvering. A slight pull on the steering wheel or a blip of the throttle will stop the hiss for a few seconds or so. Later "Anti-Sink" cars have a dual output pump, referred to as a 6+2 pump due to the number of internal piston chambers. Such cars therefore have no need of the "FDV" and therefore do not hiss.
  • 2000 Citroën XM hatchback (2010-11-28).jpg

    Hatchback (facelift)

  • Citroen XM Safari long time resident.JPG

    Break (facelift)

  • 1995 Citroën XM Break (5416867196) (cropped).jpg

    Break (facelift)

  • XM Tissier.jpg

    Citroën XM twin rear-axle ambulance by Tissier

ChassisEdit

SuspensionEdit

File:Citroen XM-Rear.jpg
1994–2000 Citroën XM (suspension fully lowered)

The hydropneumatic self-leveling suspension used grapefruit-sized metal spheres containing nitrogen acting as both springs and shock absorbers, along with an electronic control system marketed as Hydractive. Sensors in the steering, brakes, suspension, throttle pedal and transmission transmitted car's speed, acceleration, and road conditions to on-board computers to control the ride. The chassis needed very few modifications to handle nearly double the power in the V6 24V compared to the lowest-end models; the only difference was a somewhat sturdier rear stabiliser bar.<ref name=TV0691.13>Collin 1991, p. 13</ref>

The Hydractive system was somewhat "ahead of the curve" when the car was launched and early versions were sometimes unreliable. Many problems stemmed from the sensitive electronics controlling the car's hydraulic system, often caused by the poor quality of the multipoint grounding blocks – one on each front inner wing, one at the rear, and one under the dashboard. These tended to corrode (especially the ones in the engine compartment), causing all manner of intermittent faults which were hard to diagnose. On later cars, these were changed to screw terminals bolted through the bodywork, and most of the older cars have been modified in a similar way.Template:Citation needed

When the Hydractive system worked, the result was a big car with a smooth "magic carpet" ride, and better handling than many smaller, lighter, sports cars. When it didn't work, it was quite harsh and bumpy, although no worse than any contemporary high-performance sports sedan.

Although the Hydractive suspension coped superbly with undulations and driving at speed, it could be unexpectedly harsh if a sudden change in road height was encountered at moderate speed - e.g. lateral ridges or speed bumps. Citroën finally addressed this, and for Xantia (which shared the Hydractive system with XM) came up with a modified design of the suspension (centre sphere) regulator valves, which made them immune to hydraulic impulses produced by the road surface, and which could push the older-type valves into Firm mode, just when this wasn't needed. The modified valves were fitted to production Xantias from 8 March 1999 (and were available as replacements), but were not fitted to XM, which was nearing end of production. Interest in these new-type valves has led to a good few XM owners successfully fitting them, and benefiting from a noticeable improvement in smoothness and consistency of ride.

Some production models of the XM were not equipped with the Hydractive system, but had a 'conventional' hydropneumatic suspension closer to that of the Citroën BX. These lower specification vehicles were all built for markets in mainland Europe.

DIRAVI steeringEdit

Template:More citations needed A function much missed by Citroën enthusiasts was the "DIRAVI" System, previously present in the SM and CX. This option was only available for the French or LHD Export market and then only on the 3.0 V6 models. The functionality varied from car to car, but simply put the system affects steering control, at lower speeds less steering centering force aids parking and make city driving easier, but at higher speeds the system makes the steering heavier keeping you in a straight line on highways and suppressing the "sneeze" factor inherent to fast steering ratios. Another helpful function of DIRAVI is its ability to return the steering wheel to its central or neutral position when let go by the driver, even when the car is stationary. This is especially helpful when parking as the driver can be assured that his or her wheels will be in the correct position when the ignition is turned off; again this function also aids high speed, straight line driving on highways etc. Although an odd sensation to start with, most Citroën drivers become accustomed to DIRAVI in a very short time, only appreciating its unique abilities when they let go of the steering wheel in a car without DIRAVI, only to find nothing happens. DIRAVI makes the tendency of all cars' steering to return to center constant in DIRAVI equipped Citroëns, rather than being affected by tire adhesion, road tilt, tire pressure, tire failure, etc.

EnginesEdit

The XM was fitted with a wide range of gasoline and diesel engines:<ref name="AR92">Template:Citation</ref>

Model Engine Displacement Valvetrain Fuel system Max. power at rpm (DIN) Max. torque at rpm (DIN) 0–100 km/h (0-62 mph) Top speed Years
Petrol engines
2.0 XU10 2C/K 1998 cc SOHC 8v Carburettor Template:Convert at 5,800 rpm Template:Convert at 2,250 rpm 12.2 s Template:Convert 1989–1992
2.0 cat XU10 M-Z Single-point fuel injection Template:Convert at 5,600 rpm Template:Convert at 3,500 rpm 12.4 s Template:Convert 1989–1994
2.0 inj. XU10 J2/K Multi-point fuel injection Template:Convert at 5,600 rpm Template:Convert at 4,800 rpm 11.5 s Template:Convert 1989–1992
2.0 inj. cat XU10 J2C (RFU) Template:Convert at 5,600 rpm Template:Convert at 4,000 rpm 11.9 s Template:Convert 1989–1994
2.0 i 16V XU10 J4R (RFV) DOHC 16v Template:Convert at 5,500 rpm Template:Convert at 4,200 rpm 10.8 s Template:Convert 1994–2000
2.0 i Turbo CT XU10 J2TE (RGY) SOHC 8v Template:Convert at 4,400 rpm Template:Convert at 2,200 rpm 9.8 s Template:Convert 1992–1994
2.0 i Turbo CT XU10 J2TE (RGX) Template:Convert at 5,300 rpm Template:Convert at 2,500 rpm 9.3 s Template:Convert 1994–2000
3.0 i V6 PRV ZPJ S6A 2975 cc SOHC 12v Template:Convert at 5,600 rpm Template:Convert at 4,600 rpm 8.9 s Template:Convert 1989–1993
3.0 i V6 PRV ZPJ S6A 2963 cc Template:Convert at 5,600 rpm Template:Convert at 4,600 rpm 9.7 s Template:Convert 1993–1997
3.0 i V6 24V PRV ZPJ4/Y3 2975 cc SOHC 24v Template:Convert at 6,000 rpm Template:Convert at 3,600 rpm 8.6 sTemplate:Efn Template:Convert 1990–1993
3.0 i V6 24V PRV ZPJ4 SKZ<ref>Citroën Technical bulletin for XM. Bulletin binder number MAN 058930</ref> 2963 cc Template:Convert at 6,000 rpm Template:Convert at 3,600 rpm 8.6 s Template:Convert 1993–1996
2.9 i V6 24V ES9 J4 (XFX) 2946 cc DOHC 24v Template:Convert at 5,500 rpm Template:Convert at 4,500 rpm 8.4 s Template:Convert 1997–2000
Diesel engines
2.1 D12 XUD11 A (PJZ) 2138 cc SOHC 12v Indirect injection Template:Convert at 4,600 rpm Template:Convert at 2,000 rpm 17.6 s Template:Convert 1989–1994
2.1 Turbo D12 XUD11 ATE (PHZ) 2088 cc Template:Convert at 4,300 rpm
with EGR: Template:Convert		 Template:Convert at 2,000 rpm
with EGR: Template:Convert		 12.4 s Template:Convert 1989–1994
2.1 Turbo D12 XUD11 BTE (P8C) Template:Convert at 4,300 rpm Template:Convert at 2,000 rpm 12.9 s Template:Convert 1994–2000
2.4 Turbo D12 DK5 ATE/L (THY) 2446 cc Template:Convert at 4,300 rpm Template:Convert at 2,000 rpm 12.1 s Template:Convert 1994–2000
Template:Notelist

Being part of the PSA Peugeot-Citroën company, most of these engines were found in contemporary PSA cars, like the Citroën Xantia, Citroën C5, Peugeot 405, Peugeot 406 and Peugeot 605. The ZF 4HP18 automatic transmission – the late V6 had 4HP20 – was used also in Saab 9000, Peugeot 605, Alfa Romeo 164, Lancia Thema and the Fiat Croma.

Dimensions and weightsEdit

ReliabilityEdit

Electrical connectorsEdit

The XM's reliability became suspect due to a problem with the quality of electrical connector used.

Cost-cutting on the components was needed since the parent company was in financial difficulty at the time of the design of the XM. Between 1980 and 1984 the company lost $1.5 billion. <ref>Template:Cite news</ref>

Poor electrical connections would stop the car, and require extensive investigation by a trained mechanic to repair. This point was driven home in one of the final reviews of 2000, when Richard Bremner's polemical "Parting Shot" essay in Car emphasized these electrical faults. Bremner paid less attention to the remediation of the problem and to the fact that changed market conditions meant demand for the XM was never going to be the same as for its predecessor.<ref name="ReferenceB">CAR magazine, November 2000, page 250</ref>

Headlight issuesEdit

Components supplier Valeo designed the XM's lamps and a similar design was used on the Eagle Premier.<ref>Template:Cite book</ref> The goal of the design was to reduce the size of the lamps and to increase their output. The XM's new "complex surface" headlamps were not powerful enough on dipped beam,<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> though main beam was perfectly adequate. This could be traced to the use of a plastic optical element between the bulb and the outer lens, which yellowed with age.

The XM was not alone here; the pre-facelifted first-generation Ford Mondeos suffered from the same problem.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Series 2 (from mid-1994 onwards) LHD XMs had improved light units without the plastic element, but slow United Kingdom sales meant these were never fitted to RHD forms. Headlamp retrofit kits using dual or triple round optics are available from third party suppliers, though this changes the aesthetics of the car. Series 1 cars can be fitted with series 2 headlights.

US importEdit

File:1992 Citroën XM Vitesse in Emerald Green, front left.jpg
Citroën XM Vitesse (Federalized model converted by CxAuto)

The XM was imported into the United States by CXA, a company that had imported several hundred CX25 GTi and Prestige model cars for Citroën loyalists in the USA. These cars can be recognized by small filler plates at the headlights, as CxAuto installed the slightly narrower headlight units from the 1988–1993 Pontiac Grand Prix.

CxAuto presented the XM at the 1991 New York Motor Show, in the spring of 1991 and began converting and selling the XM Pallas (combined with the 2.0 injection engine) and the XM Vitesse (combined with the 3.0 V6 engine). In 1993, the XM Exclusive was added to the range. Unfortunately, the XM cost 40 percent more than the CX Prestige, with a price in excess of $50,000 due to the costs needed to modify the cars for US approval and only a few examples were sold. As a result of newer, tougher US anti-pollution standards, the import of these cars ceased in 1997.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> XM parts must be sent over from Europe.

Chinese productionEdit

The Citroën XM, along with the Citroën Xantia were assembled in a form of CKD in Huizhou, Guangdong province. This venture lasted for only two years in 1996 and 1997 and production numbers were extremely low. The cars were imported to China more or less fully assembled with only minor additions done in China as a way to avoid the high import tariffs on cars that existed at the time.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The two models were given the same name: Fengshen Xietuolong XM.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

ReferencesEdit

Template:Reflist

External linksEdit

Template:Sister project

{{#invoke:Navbox|navbox}} Template:Citroën timeline 1980 to date Template:Heuliez

Retrieved from "https://zalansite.site/mediawiki/index.php?title=Citroën_XM&oldid=355081"