Incubator escapee wiki

Ford FE engine

Article Discussion

Template:Infobox engine

The Ford FE engine is a medium block V8 engine produced in multiple displacements over two generations by the Ford Motor Company and used in vehicles sold in the North American market between 1958 and 1976. The FE, derived from 'Ford-Edsel',<ref>Template:Cite news</ref> was introduced just four years after the short-lived Ford Y-block engine, which American cars and trucks were outgrowing. It was designed with room to be significantly expanded, and manufactured both as a top-oiler and side-oiler, and in displacements between Template:Cvt and Template:Cvt.

Versions of the FE line designed for use in medium and heavy trucks and school buses from 1964 through 1978 were known as "FT," for 'Ford-Truck,'<ref>Template:Cite book</ref> and differed primarily by having steel (instead of nodular iron) crankshafts, larger crank snouts, smaller ports and valves, different distributor shafts, different water pumps and a greater use of iron for its parts.

The FE block was manufactured by using a thinwall casting technique, where Ford engineers determined the required amount of metal and re-engineered the casting process to allow for consistent dimensional results. A Ford FE from the factory weighed Template:Cvt with all iron components, while similar seven-liter offerings from GM and Chrysler weighed over Template:Cvt. With an aluminum intake and aluminum water pump the FE could be reduced to under Template:Cvt for racing.

The engine was produced in 427 and 428 cu in high-performance versions, and famously powered Ford GT40 MkIIs to endurance racing domination in the 24 hours of Le Mans during the mid-1960s.

Template:TOC limit

DescriptionEdit

{{ safesubst:#invoke:Unsubst||date=__DATE__ |$B= {{ safesubst:#invoke:Unsubst||date=__DATE__ |$B= Template:Ambox }} }} Template:Original research section

File:Ford FE engine cutaway.jpg
Cutaway showing thin-walled, deep-skirted, Y-shaped FE block (ending above the darker colored rectangular oilpan)

The FE and FT engines are medium blockTemplate:Citation needed designs, referred to as Y-block because the cylinder block casting extends below the crankshaft centerline,Template:Citation needed giving great rigidity and support to the crankshaft's main bearings. In these engines, the casting extends Template:Cvt below the crankshaft centerline, which is more than an inch below the bottom of the crank journals.

Blocks were cast in two major groups: top-oiler and side-oiler. The top-oiler block sent oil to the top center first, the side-oiler block sent oil along a passage located on the lower side of the block first.

All FE and FT engines have a bore spacing of Template:Cvt, and a deck height (distance from crank center to top of block) of Template:Cvt. The main journal (crankshaft bearing) diameter is Template:Cvt. Within the family of Ford engines of the time, the FE was neither the largest nor smallest block. Template:Anchor

FE/FT engine displacements
Displacement Type Bore+0.0036/-0.0000 Stroke+/-0.004
Template:Cvt   FT Template:Cvt Template:Cvt
Template:Cvt   FE Template:Cvt Template:Cvt
Template:Cvt Template:Cvt
Template:Cvt   FT Template:Cvt
Template:Cvt   FE
Template:Cvt
  FT
Template:Cvt Template:Cvt
Template:Cvt   FE
Template:Cvt   FT Template:Cvt
Template:Cvt   FE Template:Cvt Template:Cvt
Template:Cvt Template:Cvt Template:Cvt
Template:Cvt Template:Cvt Template:Cvt
Template:Cvt Template:Cvt Template:Cvt
Template:Cvt Template:Cvt Template:Cvt

Template:Anchor

Ford V8 blocks in the last half of the 20th century, classified by bore spacing
Small block Medium block Big block
Spacing Displacement AKA Spacing Displacement AKA Spacing Displacement AKA
Template:Cvt Template:Cvt Y-block Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt MEL
Template:Cvt Template:Cvt Y-block Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt MEL
Template:Cvt Template:Cvt Y-block Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt MEL
Template:Cvt Template:Cvt Y-block Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt MEL
Template:Cvt Template:Cvt Windsor Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt 385-series
Template:Cvt Template:Cvt Windsor Template:Cvt Template:Cvt FE Template:Cvt Template:Cvt 385-series
Template:Cvt Template:Cvt Windsor Template:Cvt Template:Cvt FE
Template:Cvt Template:Cvt Windsor Template:Cvt Template:Cvt FE
Template:Cvt Template:Cvt 335-series Template:Cvt Template:Cvt FT
Template:Cvt Template:Cvt 335-series Template:Cvt Template:Cvt FT
Template:Cvt Template:Cvt 335-series Template:Cvt Template:Cvt FT
File:Wiki 0 Oiling Patterns.jpg
FE oil flow paths

Template:Anchor FE engines came in a wide variety of configurations, including:

  • Carbureted, including single two-barrel, single four-barrel, dual four-barrel, triple two-barrel, and quad Webers, or fuel injected
  • With a top- or side-oiling block.
  • With low-rise, medium-rise, high-rise, tunnel-port, or SOHC intake manifolds.

The low-rise intake, designed to fit under a low hoodline, was the first. The high-rise intake required a hood bubble for clearance. While the low- and medium-rise heads could be used in combination with either low- or medium-rise intakes, the high-rise head required a high-rise intake due to the increased height of the intake port. The medium-rise intake port is shorter and wider than the low-rise port. The high-rise ports are taller than either the low- or medium-rise ports. Low-rise intakes have the carburetor placed relatively low; the air-fuel mix must follow a more convoluted path to the combustion chambers. A high-rise intake places the carburetor approximately Template:Cvt higher so the air-fuel mixture has a straighter path.

The tunnel-port and SOHC heads require their own matching intakes.

Within the major head groups, there are also differences in combustion chamber designs: small chambers, machined ones, and large ones. The size and type of chamber affects the compression ratio, as well as the overall performance characteristics of the engine.

GenerationsEdit

Generation 1Edit

332Edit

The "332" was the original FE engine, with a displacement of Template:Cvt, the series' smallest. It had Template:Cvt bore and a Template:Cvt stroke, and was used in Ford-brand cars in 1958 and 1959, domestically marketed U.S.- and Canadian-built Edsel-brand cars in 1959, and in export-configured 1958 and 1959 Edsels.<ref name="1959 Edsel SDB">Template:Cite book</ref><ref name="1958 Ford Brochure">Template:Cite book</ref><ref name="1959 Ford Brochure">Template:Cite book</ref><ref name="1958 Edsel SDB">Template:Cite book</ref> The two-barrel version produced Template:Cvt, a Holley or Autolite four-barrel version Template:Cvt.

332 engine configurations and applicationsEdit

352Edit

File:1964 Ford Galaxie 500 XL 352 engine.JPG
352 FE V8 in a 1964 Galaxie 500 XL

Introduced in 1958 as part of the Interceptor line of Ford V8 engines, the Ford 352 of Template:Cvt actual displacement was the replacement for the Lincoln Y-block. It is a stroked 332 with Template:Cvt stroke and a Template:Cvt bore, and was rated from Template:Cvt with a 2-barrel carburetor to over Template:Cvt on the 4-barrel models. When these engines were introduced, they were called Interceptor V-8 on the base models and Interceptor Special V-8 on the 4-barrel models.<ref name="1958 Ford Brochure"/> The 1958 H vin coded 352 was designated as Interceptor V-8 Thunderbird Special.<ref>1958 Ford V8 Cars & Thunderbird Service Manual pg 483.</ref> The Interceptor was the base-performance engine in 1958. For the 1959 model year, the FE engine series was renamed the Thunderbird V-8 and the Thunderbird Special V-8.<ref name="1959 Ford Brochure"/> When installed in Mercury vehicles, these engines were named "Marauder". This series of engines usually weighed over Template:Cvt.<ref>Template:Cite book</ref> In 1960 Ford created a high-performance version of the 352 rated at Template:Convert it featured an aluminum intake manifold, Holley 4100 4-barrel carburetor, cast iron header-style exhaust manifolds, 10.5:1 compression ratio, and solid lifters.

352 engine configurations and applicationsEdit
File:FE reference in Edlelbrock Ad 1958.jpg
1958 Advertisement for reference

361 EdselEdit

File:1959 Edsel Corsair 361 engine.JPG
361 FE V8 in a 1959 Edsel Corsair

Edsel 361 engines were assembled in Cleveland Ohio, and Dearborn Michigan. They were standard equipment in the 1958 Edsel Ranger, Pacer, Villager, Roundup and Bermuda.<ref name="1958 Edsel SDB"/> The Edsel 361 was the very first FE block engine to be offered for sale in any market, having been introduced to the public in the U.S. on September 4, 1957, almost two months before any 1958 Fords were sold.<ref>Template:Cite book</ref> The 361 cid 4V FE engine was also sold on 1959 Edsels in the U.S. and Canada, and 1958 and 1959 Ford and Meteor brand automobiles in Canada in place of the 352 cid, which was not available with any Ford Motor Company of Canada brand until the 1960 model year. Edsel 361 engines were available to U.S. law enforcement agencies and state and municipal emergency services purchasing fleet Fords as the 1958 Ford "Police Power Pack."<ref>Template:Cite book</ref><ref>Template:Cite book</ref><ref>Template:Cite book</ref>

361 Edsel engine configurations and applicationsEdit

360 TruckEdit

The 361/360, of Template:Cvt actual displacement, was introduced in 1968 and phased out at the end of the 1976-year run; it was used in the Ford F Series trucks and pickups. It has a bore of a 390 (Template:Convert) and used the 352's Template:Cvt rotating assembly. 361s and 360s were also constructed with heavy duty internal components for truck use. Use of a standard 352/390 cam for use in passenger cars along with carburetor and distributor adjustment allowed the 360 to give performance similar to that of the 352 and 390 car engines. Rated at Template:Cvt at 4100 rpm and Template:Cvt of torque at 2600 rpm (2-barrel carb, 1968). The 360 used the same block, heads and other parts as a 390, this makes them indistinguishable from each other unless the stroke is measured.

360 Truck engine configurations and applicationsEdit
  • 2V, 8.4:1
    • Template:Cvt at 4100 rpm and Template:Cvt at 2600 rpm
      • 1968–1971 Trucks<ref>Verified from 1971 Ford Truck Shop Manual First Print date November 1970 Volume 2 Engine pg 21-23-31 Sec. 9 Specifications General Specifications</ref>
    • Template:Convert net at 4000 rpm and Template:Cvt at 2400 rpm
      • 1972–1976 Trucks

390Edit

File:1969 Ford Mustang 390 FE.JPG
390 FE V8 in a 1969 Ford Mustang

The 390 had a bore of Template:Convert, stroke of Template:Convert, and displacement of Template:Cvt. It was the most common FE engine in later applications; used in many Ford cars as the standard engine, including the Thunderbird, and in many trucks as well. It was a popular high-performance engine;<ref>Template:Cite book</ref> although not as powerful as the 427 and 428 models, it provided good performance, particularly in lighter-weight vehicles. The Template:Cvt 2v is rated at Template:Cvt at 4,100 rpm, while the 4v version was rated at Template:Cvt at 4,100 rpm in certain applications. Certain 1967 and 1968 Mustangs had 390 4v engines rated at Template:Convert, as did some Fairlane GTs and S code Mercury Cougars. Template:Citation needed span

390 engine configurations and applicationsEdit

Generation 2Edit

Template:Expand section

406Edit

File:Ford 406 TriPower.jpg
406 with TriPower intake and carbs, on a Ford Galaxie

The 406 engine was introduced in 1962 and only lasted till 1963, giving way to the 427. It used a new Template:Convert bore with the 390's Template:Convert stroke, giving a displacement of Template:Cvt, rounded up to "406" for the official designation. The larger bore required a new block casting design allowing for thicker walls, but otherwise was very similar to the 390 block.<ref>Clarke, p. 11</ref>

Testing of the 406, with its higher power levels, led to cross-bolted mains – that is, main bearing caps that were secured not only by bolts at each end coming up from beneath, but also by bolts coming in from the sides through the block. A custom fit spacer was used between the cap and the block face. This design prevented the main bearing caps from "walking" under extreme racing conditions, and can be found today in many of the most powerful and modern engines from many manufacturers.

406 engine configurations and applicationsEdit

410Edit

The 410 engine, used in 1966 and 1967 Mercurys (see Ford MEL engine regarding 1958 senior series Edsels), used the same Template:Cvt bore as the 390 engine, but with the 428's Template:Cvt stroke, giving a Template:Cvt real displacement. The standard 428 crankshaft was used, which meant that the 410, like the 428, used external balancing. A compression ratio of 10.5:1 was standard.

410 engine configurations and applicationsEdit

427Edit

File:1966 Ford Galaxie XL convertible 427 engine.JPG
427 FE V8 in a 1966 Galaxie XL
File:FE tunnelport intake pushrod tubes.jpg
Tunnelport intake showing the brass tubes for the pushrods to pass through

The 427 V8 was introduced in 1963 as a "top-oiler", changed to a side-oiler in 1965. Despite the "427" designation, its true displacement was Template:Cvt. The stroke was the same as the 390 at Template:Convert, but the bore was increased to Template:Convert. The block was made of cast iron with a specially thickened deck to withstand higher compression. The cylinders were cast using cloverleaf molds— the corners were thicker all down the wall of each cylinder. Many 427s used a steel crankshaft, and all were balanced internally. Most 427s used solid valve lifters, with the exception of the 1968 block, which had oil passages drilled for hydraulic lifters. Higher flow heads were available with matching "tunnel port" intake manifolds, which routed pushrods through the intake's ports in brass tubes. As an engine designed for racing, it had many performance parts available both from the factory and the aftermarket. This engine was also used in the A/FX-cars like the famous Fairlane Thunderbolt.

Two different 427 blocks were produced, the initial 1963 top oiler and starting in 1965 a side oiler. The top oiler delivered oil to the cam and valvetrain first and the crank second; the side oiler sent oil to the crank first and the cam and valvetrain second. This was similar to the oiling design from the earlier Y-block. The engine was available with low-rise, medium-rise, or high-rise manifolds, and either single or double four-barrel carburetors on an aluminum intake.Template:Clarify span Ford never released an official power rating.

The side-oiler-powered Ford GT40 MkIIs to a 1-2-3 finish in the 1966 24 Hours of Le Mans,<ref>Ford v Ferrari GT40 hero car headed to Mecum auction</ref> and the winner's podium in 1967.<ref>What's So Special About the Side-Oiler? Race Car Network Magazine, Don Larson, March 7, 2018</ref>

427 engine configurations and applicationsEdit
  • Low-riser intake, 4V
    • 10.9:1 — Template:Convert at 5600 rpm and Template:Cvt at 3200 rpm
      • 1968 Mercury Cougar GT-E only (it was to be offered in the Ford Mustang, according to early press releases, but there are no records or verification of any factory 427 Mustangs). In the spring of 1968, the 428 Cobra Jet officially replaced the 427; however, leftover 427s were installed until late June of that year, when stocks were depleted.
    • 11.6:1 — Template:Cvt at 5600 rpm and Template:Cvt at 3400 rpm
      • 1963–1964 Ford
      • 1963–1964 Mercury
  • Low-riser intake, 2x4V
  • High-riser intake, 2x4V

|CitationClass=web }}</ref> Mercury

|CitationClass=web }}</ref>

427 SOHC "Cammer"Edit
File:Ford 427 Cammer engine no. 003.jpg
A 427 Cammer once used by Ford's "X-Garage" skunkworks
File:Wiki 66 SOHC timing chain and cam.jpg
Ford's 427 cu in/7.0 L Cammer SOHC hemi-head V8 showing cam, rockers and timing chains

The Ford single overhead cam (SOHC) 427 V8 engine, familiarly known as the "Cammer",<ref name="Scale">Scale Auto, 6/06, p.15 sidebar.</ref> was released in 1964 in an effort to maintain NASCAR dominance by seeking to counter the enormously large block Chrysler 426 Hemi "elephant" engine. The Ford 427 block was closer dimensionally to the smaller 392 cu. in. first generation Chrysler FirePower Hemi; the Ford FE's bore spacing was Template:Cvt compared to the Chrysler 392's Template:Cvt. The Ford FE's deck height of Template:Cvt was lower than that of the Chrysler 392 at Template:Cvt. For comparison, the 426 Hemi has a deck height of Template:Cvt and bore spacing of Template:Cvt; both Chrysler Hemis have decks more than Template:Cvt taller than the FE.

The engine was based on the high performance 427 side-oiler block, providing race-proven durability. The block and associated parts were largely unchanged, but an idler shaft replaced the camshaft in the block, which necessitated plugging the remaining camshaft bearing oiling holes.

The cast-iron heads were designed with hemispherical combustion chambers and a single overhead camshaft over each head, operating shaft-mounted roller rocker arms. The valvetrain consisted of valves larger than those on Ford wedge head engines, made out of stainless steel and with sodium-filled exhaust valves to prevent the valve heads from burning, and dual valve springs. This design allowed for high volumetric efficiency at high engine speed.

The idler shaft in the block in place of the camshaft was driven by the timing chain and drove the distributor and oil pump in conventional fashion. An additional sprocket on this shaft drove a second "serpentine" timing chain, Template:Cvt long, which drove both overhead camshafts. The length of this chain made precision timing of the camshafts an issue at high RPM.

The engine also had a dual-point distributor with a transistorized ignition amplifier system, running 12 amps of current through a high-output ignition coil.

The engines were essentially hand-built for racing, with combustion chambers fully machined to reduce variability. Nevertheless, Ford recommended blueprinting before use in racing applications. With a single four-barrel carburetor they weighed Template:Cvt<ref>Clarke, p. 42 et seq.</ref> and were rated at Template:Convert at 7,000 rpm and Template:Cvt of torque at 3,800 rpm, with dual four-barrel carburetors Template:Convert at 7,500 rpm and Template:Cvt of torque at 4,200 rpm. Ford sold them via the parts counter, the single four-barrel model as part C6AE-6007-363S, the dual carburetor model as part C6AE-6007-359J for $2350.00 (as of October, 1968).

Ford's hopes to counter Chrysler were, however, cut short. Although enough 427 SOHCs were sold to have the design homologated, Chrysler protests succeeded in getting NASCAR to effectively legislate the engine out of competition. This was due to the motor not being available in a factory production motor vehicle.<ref name="autoweek.com">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> It was not the only engine ever banned from NASCAR; the 1963 Chevrolet 427 ‘mystery motor’, the 1965 426 ‘Race Hemi’ and the Chrysler A-925 DOHC Hemi were also banned during the 1960s for the same reason.<ref name="autoweek.com"/> This scuttled the awaited 1965 SOHC versus Hemi competition at the Daytona 500 season opener.

Nevertheless, the SOHC 427 found its niche in non-stock drag racing, powering many altered-wheelbase A/FX Mustangs,<ref name="Scale" /> and becoming the basis for a handful of supercharged Top Fuel dragsters, including those of Connie Kalitta, Pete Robinson, and Lou Baney (driven by Don "the Snake" Prudhomme). In 1967 Connie Kalitta's SOHC-powered "Bounty Hunter" slingshot dragster won Top Fuel honors at AHRA, NHRA and NASCAR winter meets, becoming the only "triple crown" winner in drag racing history.<ref>Steve Magnante|Inside the Swamp Rat's Nest|Street Rodder Premium Magazine|page 52|Volume 2 Number 2 Winter, 2011</ref> It was also used in numerous nitro funny cars including those of Jack Chrisman, "Dyno" Don Nicholson, Eddie Schartman, Kenz & Leslie, and in numerous injected gasoline drag racing vehicles.

428Edit

File:Ford FE 428 Police Interceptor.jpg
Ford FE 428 Special Interceptor engine from a 1967 Shelby GT500

For 1966 Ford combined attributes that had worked well in previous incarnations of the FE – a Template:Cvt bore and a Template:Cvt stroke – to create an easier-to-makeTemplate:How Template:Cvt engine. It used a cast nodular iron crankshaft and external balancer.

428 FE engines were fitted to Galaxies (badged simply as '7 Litre') and Thunderbirds in the 1966 and 1967 model years. It was also found in Mustangs, Mercury Cougars, some AC (Shelby) Cobras and various other Fords from 1968. This engine was also available as standard equipment in 1966 and 1967 in the Mercury S-55.<ref>Template:Cite book</ref>

428 engine configurations and applicationsEdit
  • 4V, 10.5:1
    • Template:Convert at 4600 rpm and Template:Cvt at 2800 rpm
      • 1966–1967 Ford
      • 1966–1967 Ford Thunderbird
      • 1966–1967 Mercury
      • 1966-1967 Ford 7-Litre
      • 1966-1967 Mercury S-55
    • Template:Convert at 5400 rpm and Template:Cvt at 3200 rpm
      • 1966–1970 Ford Police Interceptor
      • 1966–1970 Mercury Police
      • 1969 Shelby GT500KR

Interceptor

428 Cobra JetEdit
File:1969 Ford Mustang Cobra Jet 428 (15687554723).jpg
428 CJ with shaker scoop (1969 Mustang)

The 428 Cobra Jet was a performance version of the 428 FE. Launched in April 1968, it was built on a regular production line using a variety of cylinder heads<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> combined with a 735 CFM Holley four-barrel carburetor. The Cobra Jet used heavier connecting rods with a 13/32 rod bolt and a nodular iron crankshaft casting #1UB. A Holman and Moody specially prepared "stripper", which carried no sound deadener, undercoating, or any optional factory equipment, was used as the introductory press car in 1968.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

The 428 Cobra-Jet had a compression ratio of 10.8:1 and was rated Template:Cvt at 5200 rpm and Template:Cvt at 3400 rpm. Historical road test data on actual production 428 CJ cars suggest peak output in the neighborhood of 275 SAE Net ("as installed") HP, using published trap speed and "as tested" weights, and Hale's trap speed formula.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Period road tests revealed quarter mile performance in the low 14-second to very high 13-second range, with trap speeds around Template:Cvt:<ref>Template:Cite magazine</ref>

The 428 Cobra Jet engine (modified to the NHRA Stock and Super Stock technical specifications) made its drag racing debut at 1968 NHRA Winternationals, held from February 2–4, 1968, at the Auto Club Raceway at Los Angeles County Fairgrounds, in Pomona, California. Ford Motor Company sponsored five drivers (Gas Ronda, Jerry Harvey, Hubert Platt, "Dyno Don" Nicholson, Kenneth McLellan, and Al Joniec) to race six 428 CJ-equipped Mustangs. They raced in classes C Stock Automatic (C/SA, Template:Cvt), based on advertised horsepower) and Super Stock E (SS/E or SS/EA, manual or automatic transmission, respectively, at Template:Cvt, based on factored horsepower). The engine lived up to expectations as four of the cars made it to their respective class finals. Al Joniec won both his class (defeating Hubert Platt in an all-CJ final) and the overall Super Stock Eliminator title (defeating Dave Wren who ‘red lighted’ in his faster 426 Race Hemi Plymouth).<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

428 Cobra-Jet engine configurations and applicationsEdit

|CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="Specs/Data Cougar Eliminator">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

    • 1968 Ford Mustang
    • 1968 Mercury Cougar
    • 1968 Shelby GT500KR
    • 1968 Ford Fairlane
    • 1968 Ford Torino
    • 1968 Mercury Comet
    • 1968 Mercury Cyclone
    • 1969–1970 Ford Mustang
    • 1969–1970 Mercury Cougar
    • 1969 Ford Fairlane
    • 1969 Ford Torino
    • 1969 Ford Cobra
    • 1969 Mercury Montego, Cyclone and CJ
428 Super Cobra JetEdit

The 428 Super Cobra Jet (also known as the 428SCJ) used the same top end, pistons, cylinder heads, camshaft, valve train, induction system, exhaust manifolds, and engine block as the 428 Cobra Jet. However, the crankshaft and connecting rods were strengthened and associated balancing altered for drag racing. A nodular iron crankshaft casting #1UA was used as well as heavier 427 "Le Mans" connecting rods with capscrews instead of bolts for greater durability. The heavier connecting rods and the removal of the centre counterweight on the stock 428 Cobra Jet crankshaft (1UA), required an external weight on the snout of the crankshaft for balancing. A 428 Super Cobra Jet engine with oil cooler was standard equipment when the "Drag Pack" option (which came when selecting either a 3.91 or 4.30 rear end gear ratio) was ordered with cars manufactured from 13 November 1968. In addition, while the CJ and SCJ engines used the same autothermic piston casting, the piston-to-bore clearance specification between the CJ and SCJ 428 engines is slightly different, with the SCJ engines gaining a slightly looser fit to permit higher operating temperature.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> Horsepower measurements at a street rpm level remained the same.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The 428 Super Cobra Jet engine was never offered with factory air conditioning due to the location of its engine oil cooler.

428 Super Cobra-Jet engine configurations and applicationsEdit

|CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="Specs/Data Cougar Eliminator"/><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

    • 1969–1970 Ford Mustang
    • 1969–1970 Mercury Cougar
    • 1969 Ford Fairlane
    • 1969 Ford Torino
    • 1969 Ford Cobra
    • 1969 Mercury Montego, Cyclone and CJ

UseEdit

The FE series engines were used in cars, trucks, buses, and boats, as well as for industrial pumps and other equipment. Ford produced the engine from 1958 and ceased production in 1976. Aftermarket support has continued, with replacement parts as well as many newly engineered and improved components.

In Ford vehicles, the FE primarily powered full and midsize cars and trucks, though it was also installed in both pony cars and midsize muscle cars, including in dedicated drag packages like the 1964 Ford Fairlane Thunderbolt. Ford used the FE in podium-sweeping victories in its GT-40 at the 24 hours of Le Mans, supported its use in factory associated high-performance Shelby Mustangs, and Shelby made the 427 cu in version further famous in his Shelby Cobras.

Ford production vehiclesEdit

Some Ford production models in which the FE was installed:

Ford Galaxie, Ford Custom 500, Ford Mustang, Ford Thunderbird - 3rd generation, Ford Thunderbird - 4th generation, Ford LTD, Ford Torino, Ford Ranchero, Ford Talladega, Ford Fairlane, and F-Series trucks though typically only those 1 ton and lesser in capacity.

Ford regularly made updates to the design of the FE which appear as engineering codes or variations in casting numbers of parts. In addition to production casting codes, Ford also made use of "SK" and "XE" numbers if the parts were one-offs or developmental designs not approved for production. Many parts attached to Ford's racing engines carried SK and XE numbers.

Selection of vehicles in which the FE was installed as original equipment:

  • 1965 Ford Galaxie.jpg

    1965 Ford Galaxie

  • 1960 Ford Galaxie Starliner.jpg

    1960 Ford Galaxie Starliner

  • 1968 Ford Torino Squire.jpg

    1968 Ford Torino Squire

  • 1965 Ford F100 Pick Up.jpg

    1965 Ford F100 Pick Up

  • 1967 Ford Fairlane Ranchero.jpg

    1967 Ford Fairlane Ranchero

  • Red 1968 gtcs front.JPG

    1968 GTCS

  • FE vehicles Thunderbird1965.jpg

    1965 Thunderbird

  • '63 Ford Galaxie 500 Convertible (Rassemblement Saint-Bruno-De-Montarville '10).jpg

    1963 Ford Galaxie 500 Convertible

  • '59 Ford Galaxie (Auto classique Laval '10).jpg

    1959 Ford Galaxie

Other usesEdit

In addition to its use in Ford and Mercury branded vehicles, Ford itself, used it in factory, supported racing teams, and the FE was sold to third parties for use in their own products such as buses, and boats. Also, the FE was used to power irrigation pumps, generators and other machinery where long-running, low-rpm, reliable service was required.

In racingEdit

File:Ford Hemi SOHC Frontengine Rail.jpg
Ford SOHC Hemi (Cammer) front engine rail dragster
File:Wiki 7 FED configuration with xram.jpg
Flopper Funny Car FE
File:Wiki 4 TunnelPort crossram efi.jpg
Factory tunnelport crossram fuel injection used in GT40s
File:Wiki 1 427SO webers.jpg
FE with 4 Weber carburetors as installed in competition 427 AC Cobras
File:Ford GT40 (front).jpg
Ford GT40 Mk IIs finished 1-2-3 in the 1966 24 Hours of Le Mans; this car finished 2nd
File:1964 thunderbolt.jpg
1964 Fairlane Thunderbolt

Specific models that used FE engines include the AC Cobra MKIII, GT40s, the AC Frua, as well as various factory racing versions of Ford Mustangs, Ford Galaxies, Ford Fairlanes, and Ford Thunderbirds.

In the 1960s, most organized racing events required either stock components or components that were readily available to the general public. For NASCAR racing, rules required that at least 500 vehicles be sold to the general public equipped as raced. Many drag racing and road racing organizations had similar rules, which contributed to a wide range of performance parts being made available through Ford dealership parts counters. In addition, aftermarket suppliers produced performance parts and accessories.

The use of the FE by Ford itself as the powerplant in many of its racing programs and performance vehicles resulted in constant improvements and engineering changes over the course of its life. Racing-inspired changes to the FE which later made it to production engines included the side-oiler block, which directed oil first to the lower portions of the block.

Road and track racingEdit

In 1963, the 427 Galaxies dominated NASCAR primarily because in January 1963 G.M. told its divisions to get out of racing. Tiny Lund won the biggest race of the year, the Daytona 500, with 427s finishing first through fifth. Ford won 23 races to Plymouth's 19. The Plymouths earned all their victories on the short tracks while Ford dominated the super speedways, Chevrolet finished with eight wins and Pontiac had four.

In 1964, Ford had their best season ever, with 30 wins. Dodge was second with 14, while Plymouth had 12. Adding the five wins that Mercury had, the 427 had a total of 35 NASCAR Grand National wins for the 1964 season. Fred Lorenzen won the Atlanta 500 and proceeded to beat Dodges and Plymouths, which were using 426 Hemi engines, in six of the next seven races. Ford was using the high-riser intake and matching heads, which were allowed by NASCAR for one season (1964).

In 1965, NASCAR banned Ford's high-riser version of the engine, claiming they did not fit under "stock" hoods. Chrysler's 426 Hemi was banned as well, returning in 1966 after a de-tuned version was installed in a production vehicle that year. For the 1965 season, Ford developed its own version of a hemi-chambered engine, the 427 single overhead cam (SOHC) "Cammer" which used a single chain-driven overhead camshaft per head to operate the valves in its hemi. NASCAR relegated the engine to the fullsize Galaxie. Then Ford developed the medium-riser intake and head, which fit under stock hoods and was accepted by NASCAR. Ned Jarrett, driving for Ford, was the 1965 Grand National champion and Ford won the NASCAR crown.

Also in 1965, Ford and Carroll Shelby began production of a new and improved Cobra using a Template:Convert FE side-oiler in place of the original's Template:Cvt Windsor small-block. A new chassis was built enlarging 3" main tubing to 4", with coil springs all around. The new car also had wide fenders and a larger radiator opening. The S/C (for semi-competition) "street" engine was rated at Template:Cvt, which provided a top speed of Template:Cvt, and the competition version (csx 6000) Template:Cvt with a top speed of Template:Cvt. Cobra Mark III production began on 1 January 1965, and was used for racing into the 1970s. An original S/C sold in 2011 for US$1.5 million, making it one of the most valuable Cobra variants.<ref name="Supercars.net">Template:Cite news</ref>

In 1966, the 427 cubic inch Ford GT40 Mk II dominated the 24 Hours of Le Mans race, with a one-two-three result.

In 1967, Parnelli Jones, in a Holman-Moody prepped Fairlane, won the season-opening Riverside 500 road race. Then, Mario Andretti captured the Daytona 500 in a Fairlane, with Fred Lorenzen a close second in his Holman-Moody Ford. The FE again powered the 24 Hours of Le Mans winner. In 1968, the rules of the race were changed, limiting displacement to 302 cubic inches under certain circumstances. Ford won the following two years using its Ford Windsor smallblock in the GT40.

Ford's racing partner, privately owned Holman-Moody, also developed a version of the FE for the Can-Am racing series. It used factory-supplied tunnel port heads, a mechanical fuel injection system mounted on a crossram intake manifold, and a revised dry sump oiling system, but met with only limited success.

Drag racingEdit

Organized drag racing (NHRA, AHRA and even NASCAR dabbled in drag racing in the mid-1960s) was a major venue for the FE in its various forms. Many of the most innovative products were developed and used for 1/4 mile drag racing as aftermarket suppliers eagerly supported the engine design with products such as special intakes, camshafts, superchargers, manifolds, cylinder heads, water and fuel pumps, and exhaust headers. But it was the Ford company itself which developed the most potent products and platforms for the drag-racer. Beginning in 1962 and continuing through 1964, Ford made lightweight versions of its popular Galaxie model using aluminum, fiberglass and specially chosen components emphasizing light weight over comfort or style. Many parts were simply not put on the vehicle, such as a passenger side windshield wiper, sound deadening, armrests, heater, and radio.

In late 1964, Ford contracted Holman & Moody to prepare ten 427-powered Mustangs to contest the National Hot Rod Association's (NHRA) A/Factory Experimental Class in the 1965 drag racing season. Five of these special Mustangs made their competition debut at the 1965 NHRA Winternationals, where they qualified in the Factory Stock FX Eliminator Class for (FX cars only). The car driven by Bill Lawton won the class.<ref>Morris, Charlie. "Ford's 1965 Factory Experimental Mustangs" Template:Webarchive, Car Tech Inc. website, undated article. Retrieved on August 26, 2008.</ref>

For the 1964 model year, Ford introduced the two-door Fairlane 500 sedan-based Thunderbolt. Modified to accept a 427 high-riser engine, it featured a teardrop-shaped bubble hood to clear the induction system and drivetrain components from the larger Galaxie model. The two inner headlights were eliminated and replaced with air inlets ducted directly to the two four-barrel carbs. It was an industry first, the only time that a turn key drag car was made available to the general public.<ref>Dennis Kolodziej. (Ford) Thunderbolt Details. Fordfe.com. 2011-04-15.Accessed: 2011-04-15. (Archived by WebCite at)</ref> However, the extensive modifications to the car did not meet Ford appearance quality standards.<ref name="Hot Rod disclaimer">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref name="1964 Lightweight">{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

THIS VEHICLE HAS BEEN BUILT SPECIALLY AS A LIGHTWEIGHT COMPETITIVE CAR AND INCLUDES CERTAIN FIBERGLASS AND ALUMINUM COMPONENTS. BECAUSE OF THE SPECIALIZED PURPOSE FOR WHICH THIS CAR HAS BEEN BUILT AND IN ORDER TO ACHIEVE MAXIMUM WEIGHT REDUCTION, NORMAL QUALITY STANDARDS OF THE FORD MOTOR COMPANY IN TERMS OF EXTERIOR PANEL FIT AND SURFACE APPEARANCE ARE NOT MET ON THIS VEHICLE.

THIS INFORMATION IS INCLUDED ON THIS VEHICLE TO ASSURE THAT ALL CUSTOMERS WHO PURCHASE THIS CAR ARE AWARE OF THE DEVIATION FROM THE REGULAR HIGH APPEARANCE QUALITY STANDARDS OF THE FORD MOTOR COMPANY.<ref>Reprint of January 2000 article in Hot Rod Magazine describing the disclaimer plate on a Thunderbolt used on a road tour</ref><ref>{{#invoke:citation/CS1|citation

CitationClass=web

}}</ref>

The 1964 NHRA Super Stock meeting was captured with a Thunderbolt. However, all three NHRA Top Stock Eliminator titles were won by Chrysler's Race Hemi.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>Template:Better source needed Nearly half a century later, in 2013, a Thunderbolt set a new SS/A record of 8.55 seconds in the quarter mile, with a closing speed of 154 mph,<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

In 1963, Dick Brannan set the NHRA Super/Stock National record at 12.42 on a hot July day. In the biggest race of the year, the INDY Nationals, Ed Martin's lightweight Galaxie lost the Super Stock trophy run to John Barker's Dodge but at the teardown, the Dodge was found to have an illegal cam. In drag racing, the 427 Ford Galaxie was a winner in three consecutive National Events: the '64 Indy Nationals, the 1965 WinterNationals and the 1965 Indy Nationals. It was Mike Schmitt driving the Desert Motors Galaxie to the AA/SA Class win at the 1964 Indy Nationals. At the 1965 Winternationals it was a clean sweep as Doug Butler's four-speed took the win in AA/S with a 12.77 at 114.21 and Bill Hanyon won on the automatic side with a 12.24 at 117.95. Additionally, Bud Schellenberger's "Double A Stock" 1964 Galaxie was the 1965 Indy Nationals Top Stock Eliminator with a 12.16 at 114.21. The Shelby Super Snake top fuel dragster, powered by a 427 supercharged SOHC, became the first car in NHRA competition to break the six-second quarter-mile time barrier. It was the winner of the 1966 NHRA Spring Nationals. In every decade since, the FE has held drag-racing records. In 2011, the new decade opens with the NHRA SS/F (class rules include stock compression ratio, stock valve sizes, stock carb sizing and other OEM-type equipment limitations) national record: the quartermile in 9.29 seconds, with a closing speed of 143.63 mph.

Other closed course racingEdit

In 1970, an FE-powered vehicle set the land speed record for the U.K. Tony Densham set the new British land speed record of just over Template:Cvt over the flying kilometer (the average of two runs in opposite directions within an hour) and then held onto the record for over 30 years. The FE-powered vehicle beat the official British wheel-driven record over the flying 500 and kilometer distances, until then held by Sir Malcolm Campbell, of 174.883 mph<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Custom automobilesEdit

The FE engine is used extensively in custom installations. The extensive availability of multi-carburetor and other exotic intakes, as well as many other "dress-up parts", has contributed to its use where the engine would be shown off. FEs powered the original Batmobiles built by George Barris for the 1966 TV series. It fit under the hood along with the Bat-ray, Bat-ram, a nose-mounted aluminum chain slicer and all the associated support hardware of the 5,500-pound vehicle. One dragstrip version was equipped with a Holman-Moody prepped 427 FE with dual quads, which would be launched in second gear and spin its tires the entire quarter-mile length of the track.<ref>Template:Cite news</ref> In 1968 Carroll Shelby created a custom Mustang using a California Special model and an experimental Ford 428 FE (known as a CJX, precursor to the 428 Cobra Jet). This "Green Hornet"<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>Template:Better source needed had a custom independent rear suspension, four-wheel disc brakes and a Conelec electronically controlled port fuel injection system. It had a 5.7 sec 0-60 time and 157 mph top speed, versus a factory 428 cu in FE Shelby GT500's 6.5 second 0-60 and 128 mph top speed.<ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref><ref>{{#invoke:citation/CS1|citation |CitationClass=web }}</ref>

Marine applicationsEdit

File:Wiki 11 Marine Options.jpg
Examples of FEs installed in boats

The FE was popular in V-drive marine applications, available as a factory option in Century boats.

Beginning in 1968, the U.S. Navy SEALS used twin 427 FEs to power their Light SEAL Support Craft (LSSC).<ref>Template:Cite news</ref>Template:Better source needed

ReplacementEdit

By the mid-1970s the FE had been widely used in Ford vehicles for nearly two decades. To replace it, Ford had developed the 335-series engines, commonly referred to as "Cleveland" engines, and the 385-series engines. These were produced in displacements ranging from Template:Cvt up to Template:Cvt, including Template:Cvt, giving Ford V8s of Template:Cvt, Template:Cvt, and Template:Cvt. The last FE was installed in a production vehicle in 1976,Template:Citation needed and in the late 1970s the Dearborn Engine Plant that produced the FE engines was completely retooled to produce the 1.6-liter engine introduced in the Ford Escort in 1981.Template:Citation needed

ReferencesEdit

Template:Reflist

Further readingEdit

External linksEdit

  • {{#invoke:citation/CS1|citation

|CitationClass=web }}

Template:Ford early engine timeline

Retrieved from "https://zalansite.site/mediawiki/index.php?title=Ford_FE_engine&oldid=255555"