Water trough
Template:Short description Template:About
A water trough (British terminology), or track pan (American terminology), is a device to enable a steam locomotive to replenish its water supply while in motion. It consists of a long trough filled with water, lying between the rails. When a steam locomotive passes over the trough, a water scoop can be lowered, and the speed of forward motion forces water into the scoop, up the scoop pipe and into the tanks or locomotive tender.
OriginEdit
Steam locomotives consume a considerable amount of water, and the tender or side tanks need to be replenished at intervals. Traditionally the engine water was replenished during station stops, but if it was desired to run long distances without stopping, the requirement to take water was a significant limitation. The Railway Magazine reported a development by John Ramsbottom:
Ramsbottom arranged some experiments and showed that the forward motion of a scoop in a trough of water would force water up a connected pipe and into a tank. He calculated the quasi-static head produced by the forward motion:
The track is raised a little over a short distance each end of the trough, so that the engine, and the scoop which may already be lowered, descend into the trough:
The first installation was brought into use on 23 June 1860 at Mochdre, Conwy, on the London and North Western Railway's (LNWR) North Wales Coast Line, midway between Chester and Holyhead.<ref name = vaughan/><ref>Template:Cite bookTemplate:Page needed</ref><ref>Template:Cite bookTemplate:Page needed</ref>
The siting of the troughs requires a long enough length of straight and level track (although very large radius curves could be accommodated). For instance, the LNWR placed water troughs within the Standedge Tunnels, as they were the only sufficiently straight and level portion of the line between Huddersfield and Manchester. There must be a good water supply nearby. In hard water areas, water softening plant may have been considered necessary.<ref name = vaughan/>
Locomotive equipmentEdit
A scoop was fitted to the underside of the locomotive's tender (or the locomotive itself in the case of tank locomotives) in such a way that it could be raised or lowered, by a hand-operated screw or a power mechanism. The scoop fed into a vertical pipe that discharged into the water tank. The scoop was purposely made of light construction so that, should it strike an obstruction, it tore away, causing no serious damage to the locomotive or its trailing vehicles.
Tender locomotives generally picked up in the forward direction only.<ref name=vaughan/> Tank locomotives were not usually fitted with water scoops, but some larger tank locomotives, such as on the Lancashire and Yorkshire Railway, were and in these cases they were equipped to pick up in either direction.<ref >Template:Cite book</ref>
The scoop needed to be lowered at speed at the correct location – shortly before the start of the trough – and raised again when either the tank is full, or at the end of the trough. Failure to raise the scoop promptly when the tanks are full would resulted in large volumes of water being expelled from the vents, soaking the tender and footplate. The fireman therefore had to observe the water level indicator (a float in the tank, connected to an external pointer) carefully and be poised to retract the scoop as necessary. Lineside indicators were provided to assist engine crews in determining the location; in the UK it was a large white rectangular board with a black horizontal zigzag marking. On American railroads, illuminated trackside signals were employed for night-time usage, to indicate the start and approaching end of the track pan.
A 1934 report said that the LMS had carried out tests recently and introduced a deflector Template:Cvt ahead of the scoop to pile water in the centre of the trough, thus reducing spillage out of the troughs by about 400 gallons (1,800 L) (about 20%) for each use.<ref>Template:Cite magazine</ref>
Venting on the tender needed to be free to allow a high rate of release of expelled air from the tank.
Operational considerationsEdit
The LNWR quickly installed water troughs at other locations, but other companies were slow to adopt the new apparatus. The Great Western Railway (GWR) did so from 1895, and subsequently all the major railways in England, with the exception of the lines south of the River Thames, installed the equipment.
Taking water at speed results in considerable spray behind the scoop; this risks drenching passengers in the leading vehicles, and in Great Britain it was customary for the guard or other traincrew to warn passengers in the first coach to keep the windows closed. In one incident on the LMS railway in Britain, two streamlined trains with Coronation class locomotives happened to pass each other at a water trough when one of the trains was taking on water. The other train suffered broken windows due to lumps of tender coal scattered by the spray and the complaints from drenched passengers caused the management to retimetable the trains to ensure this could not happen again. Vaughan says that the Royal Train when conveying royalty was not permitted to be passed by another train in a section where there was a water trough.<ref name = vaughan/>
Vaughan states that the GWR investigated the effectiveness of varying train speed, and found that Template:Cvt was the optimum speed; but water could be picked up successfully as low as Template:Cvt. At that speed Template:Convert could be picked up in Template:Convert, but Vaughan suggests that this is a low theoretical figure, and that it overlooks the bow wave effect which enables a greater take-up rate. There was a significant resistance to the forward motion of the engine during the process, enough to require special care by the driver to avoid problems on unfitted freight trains.<ref name = vaughan/>
The considerable water spray made track maintenance difficult, and the physical trough equipment limited access for packing sleepers, exacerbating the problem. In very cold weather the water would freeze, preventing water pick-up, unless a heating apparatus was installed.
Track pans normally took a while to fill up after being used, so they could not be used immediately by a close-following train. They were also expensive to maintain, generally requiring a pumping station, a lot of plumbing, and an employee or two to maintain. They were thus only justified on a railroad with a high traffic volume. In the United States, several big eastern railroads used them, primarily the New York Central Railroad and Pennsylvania Railroad.
They could be found on all main lines in Britain, except on the Southern Railway.<ref>Template:Cite journal</ref><ref>Template:Cite bookTemplate:Page needed</ref><ref name = vaughan>Template:Cite magazine</ref><ref>Template:Cite magazine</ref><ref>Template:Cite journal</ref><ref>Template:Cite journal</ref> They were removed as use of steam trains decreased. When the Aber troughs were removed in 1967, the only remaining troughs were in north-west England and Scotland.<ref>Template:Cite magazine</ref>
Use by diesel locomotivesEdit
Diesel locomotives were introduced in the United Kingdom by British Railways in the 1950s, working alongside steam traction until 1968. Passenger vehicles were heated by steam from the locomotive boiler at that time, and the early diesel locomotives were provided with auxiliary boilers to provide the steam. Locomotives intended for long non-stop runs (such as the Class 40 and Class 55) were fitted with water scoops to allow them to replenish the steam generator's water supply from troughs.<ref >{{#invoke:citation/CS1|citation |CitationClass=web }}</ref> The withdrawal of steam traction and the introduction of rolling stock with electric rather than steam heating removed the need for such equipment on later types and scoop-equipped locomotives had their scoops removed.
LocationsEdit
At its creation at the start of 1923, the London and North Eastern Railway (LNER) inherited ten sets of water troughs from its constituents, and also became a co-owner (with the Great Western Railway) of one more.<ref>Template:Cite book</ref>
| Location | Previous station | Next station | Milepost (origin) | Pre-group |
|---|---|---|---|---|
| Charwelton | Template:Stnlnk | Template:Stnlnk | 135 (Manchester) | Great Central Railway |
| Eckington | Killamarsh | Eckington & Renishaw | 51 (Manchester) | Great Central Railway |
| Halifax Junction | Bentley | Template:Stnlnk | 67 (Liverpool Street) | Great Eastern Railway |
| Langley | Template:Stnlnk | Template:Stnlnk | 26 (King's Cross) | Great Northern Railway |
| Lucker | Template:Stnlnk | Template:Stnlnk | 48 (Newcastle) | North Eastern Railway |
| Muskham | Newark | Carlton-on-Trent | 123 (King's Cross) | Great Northern Railway |
| Ruislip | Ruislip & Ickenham | Template:Stnlnk | 2 (Northolt Junction) | Great Western and Great Central Joint Railway |
| Scrooby | Template:Stnlnk | Template:Stnlnk | 146 (King's Cross) | Great Northern Railway |
| Tivetshall | Template:Stnlnk | Template:Stnlnk | 100 (Liverpool Street) | Great Eastern Railway |
| Werrington | Template:Stnlnk | Template:Stnlnk | 80 (King's Cross) | Great Northern Railway |
| Wiske Moor | Template:Stnlnk | Template:Stnlnk | 32 (York) | North Eastern Railway |
A map showing the location of GWR troughs in the 1930s is reproduced in the book 'The Great Western Railway'.<ref>Template:Cite bookTemplate:Page needed</ref> They are typically at spacings of Template:Convert, but with some wide variations. There are a few instances of trough locations very close to major stopping points; for example Fox's Wood, near St Annes Park, two miles from Bristol Temple Meads; however this was installed when trains to South Wales travelled via Bath and Filton, using these troughs; after the opening of the South Wales direct route via Badminton, numerous passenger and goods trains continued to use the route and required the troughs. The lengths are also given: they vary from 524 to 620 yards (480 to 570 metres).
The locations were (in 1936):
Location Milepost In use from Length Pangbourne - Goring Template:Frac 1 October 1895 Template:Cvt Aldermaston - Midgham Template:Frac by 1904 Template:Cvt Fairwood Junction (up) Template:Frac Template:Cvt Fairwood Junction (down) Template:Frac Template:Cvt Cogload Jn – Creech Jn Template:Frac March 1902 Template:Cvt Exminster – Starcross 200 July 1904 Template:Cvt Keynsham – Fox's Wood Template:Frac 1 October 1895 Template:Cvt Chipping Sodbury 104 1 January 1903 Template:Cvt Undy – Magor Template:Frac Template:Cvt Ferryside Template:Frac Template:Cvt Denham – Ruislip Template:Frac 20 November 1905 Template:Cvt Kings Sutton Template:Frac Template:Cvt Rowington Jn Template:Frac by July 1902 Template:Cvt (Template:Cvt from 1908) Charlbury 78 Template:Cvt Bromfield – Ludlow Template:Frac Template:Cvt Lostwithiel
<ref name =ga>Great Western Railway, General Appendix to the Rule Book, 1936, quoted by Vaughan; the Lostwithiel entry comes from H Holcroft, An Outline of Great Western Locomotive Practice, quoted by Vaughan</ref>
Similar 1934 maps<ref>Template:Cite magazine</ref> showed troughs on the main East, Midland and West Coast routes from London to Scotland:
London Kings Cross to Edinburgh Waverley Location Mileage apart Length Langley – Stevenage Template:Cvt Template:Cvt Peterborough – Werrington Jn Template:Cvt Template:Cvt Muskham Template:Cvt Template:Cvt Scrooby – Bawtry Template:Cvt Template:Cvt Northallerton – Danby Wiske Template:Cvt Template:Cvt Lucker – Berwick Template:Cvt Template:Cvt Edinburgh Template:Cvt
London Euston to Edinburgh and Glasgow Location Mileage apart Length Hatch End – Bushey Template:Cvt Template:Cvt Wolverton – Castlethorpe Template:Cvt Template:Cvt Rugby – Brinklow Template:Cvt Template:Cvt Tamworth – Lichfield Template:Cvt Template:Cvt Whitmore – Madeley Template:Cvt Template:Cvt Preston Brook – Moore Template:Cvt Template:Cvt Brock – Garstang Template:Cvt Template:Cvt Hest Bank – Bolton-le-sands Template:Cvt Template:Cvt Low Gill – Tebay Template:Cvt Template:Cvt Floriston – Gretna Template:Cvt Template:Cvt Thankerton – Carstairs Template:Cvt Template:Cvt Glasgow Template:Cvt Edinburgh Template:Cvt
London St Pancras to Glasgow Location Mileage apart Length Oakley – Sharnbrook Template:Cvt Template:Cvt Loughborough – Hathern (via Leicester) Template:Cvt Template:Cvt Melton Mowbray (via Nottingham) Template:Cvt Template:Cvt Dent – Hawes (see also Garsdale railway station) Template:Cvt Template:Cvt Floriston – Gretna Template:Cvt Template:Cvt Kirkconnel – New Cumnock Template:Cvt Template:Cvt Glasgow Template:Cvt
Other British troughs are mentioned in articles on Ipswich and Tivetshall railway stations (Norfolk).
Continuous water trough supplyEdit
The Railway Magazine writer, quoted above, contemplated nearly-continuous water troughs, avoiding the transport of large quantities of water in the train:
The question has been discussed as to whether it would be possible to have a continuous supply of water all along the lines, and so obviate the necessity for tenders. Some years ago a writer in the "Engineer" put it in this way; One ton of coal will last a heavy goods train 40 miles [64 km], and an express nearly 100 miles [160 km]; but from 6 to 8 or 9 tons of water are required for the same distance. If the tender were done away with, the coals, and a small tank with a capacity of forty or fifty gallons [180 or 230 L] to receive the water, and from which to supply the boiler, would have to be carried on the engine. After allowing for these, 15 or 20 tons of paying load might be added to the train, which would be an advantage additional to the primary object—the saving of time.<ref name = rm/>
Alternative techniquesEdit
Railway companies were well aware of the cost of installing and maintaining this equipment, and the provision of tenders with a large water capacity was an alternative employed in some cases. The London and South Western Railway in England used large 8-wheel tenders nicknamed "water carts".
See alsoEdit
ReferencesEdit
<references />
External linksEdit
- [1] Vintage cine of British steam engines in the 1950s using water troughs/track pans